LDARC KKT30 Flytower Series User manual

- MPU：F405
- IMU：MPU6000
- OSD：AT7456E
- Dual BEC：Digital independent BEC
- Firmware：BETAFLIGHTF4
- Mounting size：30.5*30.5mm
- Weight：7g
KKT30-F4D
KKT30 Flytower manual
PPM
B08
GND BAT M1 M2 M3 M4 CUR
nR2 GND R1 T1 GND 10V
T6 GND T3/
SCL T2 GND GND nR2 GNE BAT-
LED BAT+
PPM
/B08
R6 +5V R3/
SDA R2 3V3 +5V nT2
G
5V
TM
10V
G
T
R1
G
nR2
R
BL
W
G
BR
Y
LED 5V BAT PPM
B08
M3 M1 T1 VO BAT G
G G CUR M4 M2 TM VI +5V G
S.BUS和PPM接收机连接方式 DSM2和DSMX接收机连接方式
T6 GND T3/
SCL T2 GND GND nR2 GNE BAT-
LED BAT+
PPM
/B08
R6 +5V R3/
SDA R2 3V3 +5V nT2
T6 GND T3 T2 GND GND nR2 GNE BAT-
LED BAT+
PPM
B08
R6 +5V R3 R2 3V3 +5V nT2
T6 GND T3 T2 GND GND nR2 GNE BAT-
LED BAT+
PPM
B08
R6 +5V R3 R2 3V3 +5V nT2
DSM2/DSMX
IBUS etc.
SBUS/PPM
Supply voltage is 3.3V
NOT invert RX2 signal input
Supply voltage is 5V
PPM or invert RX2 signal input
S.BUS and PPM receiver connection DSM2 and DSMX receiver connection
Supply voltage is 5V
NOT invert RX2 signal input
iBUS receiver connection
DJI FPV
Digital

- Firmware : OMNIBUSF4SD
- OSD : Betaflight OSD
- Ground station : Betaflight
- Output voltage : 5V
- 48CH，600mW
- IRC-Tramp
- Mounting size : 30.5*30.5mm
- Weight : 11.3g
KKT30-F4V600
VideoGND 5V outRX GNDVCC
KKT30-V600
Video GND 5V out RX GND 7-24V
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
5865 5845 5825 5805 5785 5765 5745 5725
5733 5752 5771 5790 5809 5828 5847 5866
5705 5685 5665 5645 5885 5905 5925 5945
5740
5362
5658
5760
5399
5695
5780
5436
5732
5800
5473
5769
5820
5510
5806
5840
5547
5843
5860
5584
5880
5880
5621
5917
A
Frequency table(Mhz)
CH/Band
B
E
F
R
L
25mWPower switching 100mW 200mW 400mW 600mW
FR
CH
Audio Video GND VCC GND
MMCX
VCC SBUS
Power VTX Band Channel
3.3V
GND 3.3V SIN
SBUS SPEK
(DSMX)
SIN 5V GND
UART3 RX
UART3 TX
UART1 TX
UART1 RX
UART6 TX
UART6 RX
SIGNAL
GND
VCC
CAM
BOOT
GND BZ- LED
S+
-
VCC
VTX
LED
+
-
Buzzer
Please solder the pads together
when using PPM receiver
Description
- Wide input voltage and low power consumption 7-24V
- 5V@1A high load output
- Up to 600mW of output power
- 48CH , With self-test output power function
- 30.5*30.5mm mounting size
- IRC-Tramp
Note：
- Make sure output terminal is installed antenna before power on
- Pay attention to static electricity protection during transportation and installation
Frequency and power control
- Button frequency control：shot press once to switch CH（CH1-CH8）
long press for 2s and then short press to switch frequency group FR（A-L）
- Button power control : Long press for 6s and then short press to
switch power level 25/100/200/400/600mW

- Work voltage：2-4S
- Work current：4*40A
- Max work current：4*45A（5S）
- Firmware：BLheli_S/Dshot150/300/600 16.6（G_H_30）
- Integrated battery detection
- Mounting size：30.5*30.5mm
- Weight：12.5g
KKT30-E40A
M3
M4
M1
+-
M2
4 3 2 1 B
C G G G B
KKT30-C1 Connection
DJI FPV Digital connection
VTX
ESC
FC
DJI FPV Digital

191211
KKT30-C2 & RunCam 4K connection
FC VTX
RunCam 4K ESC
FC
G
7-24 GND RX 5V out GND Video
+5VG
GND VCC(5-20V)Video
GBATVO