Le Veil iCigar Pro DCH-67 User manual

Thank you for purchasing this Le Veil product. Please read this
manual in its enrety to fully enjoy the benets and features
of this product. Please keep this manual for future reference.
Note: A clear lm is applied to the top screen face that can
be remove prior to using this product. Locate the clear tab
and simply peel to remove
Note: A clear lm is applied to the top screen face that can be remove
prior to using this product. Locate the clear tab and simply peel to remove.
• Low water alarm indicator
• Maintains up to 55 CB-FT humidors
• Up to 110 CB-FT w/sub. tank (not included)
• Two Powerful and quiet fans
• Back-lit liquid crystal display
1. Humidity sensor
2. Flat power cable
3. Power port for
support slave unit
4. Air out venlaon
5. Air in venlaon
6. Water sensor
7. Power light
8. 12V power port
9. Control buons
10. Reset memory
buon
11. Support Leg
12. MP, XS, AP ports are
for future features
13. Bluetooth Adapter
Port
4
5
10
11
6
1
2
9
8
7
3
12
Humidity
Temperature
°C , °F
3Days Avrg
Max, Min
Current humidity in humidor
Current temperature in humidor
Celsius or Fahrenheit temperature
3 day average humidity in humidor
maximum or minimum humidity
Humidier Water Level
13
Humidier Instrucons
iCigar Pro DCH-67
We Care About Quality in Cigars

*** The Flat Cable that connects the Main Controller to the Water
Tank is aached at the factory. This cable is fragile and may tear easily.
The following instrucons are how to connect the Flat Cable to avoid
any damage. ***
To connect the cable to the Main Controller unit, follow these in-
strucons
A. Open the back cover on the Main Controller unit and gently ex-
tend the cable lock out to plug in the Flat Cable head. The cable
should have the blue side facing up and be posioned in the cen-
ter.
B. Push the cable lock in to secure the Flat Cable head.
C. Replace the back cover.
D. Open the back cover on the fan enclosure and pull the cable lock
out to plug in the Flat Cable head. The cable should have the blue
side facing up and be posioned in the center.
E. Push the cable lock in to secure the Flat Cable head and replace
the back cover.
Connecon Informaon

Water Tank Setup
• Pour the bag of dry gel into the water tank.
• Add dislled or carbon ltered drinking water into the water tank,
lling to the water line. (Overlling the water tank may cause
venlaon issues and short circuits)
• Wipe o any excess water on the inside and outside of the fan unit.
• Place the cover back on the water tank as shown above. Allow 20
minutes for the gel to absorb water before use.
• Replace gel yearly.
(1) Press and hold the 'MODE' buon for 3 seconds unl the RH
seng numbers ash in the boom right of the screen.
(2) Release the 'MODE' buon and use the 'UP' and 'DOWN'
buons to raise or lower the target humidity/RH seng.
 The humidier fan will turn on and o depending on what the
RH seng is set to.
 Quickly press 'MODE' to switch from °C or °F.
 Press 'UP' or 'DOWN' to display the Max/Min humidity.
 When the water level becomes low, the LCD display will show 1
water drop and beep for 30 seconds. Push any buon to turn
o the alarm early.
 Fill the tank to the water line using dislled water. Overlling
may cause venlaon issues and short circuits.
MODE UP DOWN
Inial Setup and Operaons

Warnings
• Avoid having water near any electric connecon. Make sure
the power plug is dry before plugging it into any power outlet.
• Please do not use tap water in humidier units. Tap water will
cause damage to humidiers, humidors and cigars.
• Make sure there is gel in the tank. If you would like to use
without gel, don’t use dislled water because the water sensor
will not detect water since dislled water is too pure, instead
use carbonated ltered drinking water.
• If the Flat Cable needs adjusng, follow the provided
instrucons to avoid damaging it.
• If lime build up is seen on the two water sensor poles, clean
with de-lime or vinegar. Make sure no liquid gets into the
humidier.
Recalibrang the Hygrometer
Each Le Veil humidier is equipped with a capacive humidity sensor,
the same used in commercial laboratories. Most digital hygrometers
available are equipped with resisve sensors which can have a RH
variance of +/- 10%. Please make sure the hygrometer used to match
humidity has a capacive humidity sensor.
To calibrate the iCigar Pro humidier, hold the
'MODE' buon (keep holding it) and before the
numbers ash in the boom right corner, imme-
diately adjust the meter with the 'UP' and 'Down'
buons. The numbers on the upper le side of the humidier will
increase or decrease depending on what you need. Use this funcon to
match the humidier to the other hygrometer that you are trying to
match it to.
Factory Pre-set 70%
Humidier Accuracy +/- 1%
Humidity Range 40%-90%
Wall Outlet Power 100-240V AC, 12V DC
Size 9”Lx4 3/4W”x4 1/2”H
Engineered in USA
Manufactured in China
Patent rights issued
and /or pending
www.leveil.us