Lec+ BC6097K User manual

USER MANUAL
EfficienC Bottle Cooler Range
Applicable Models:
BC6097K/BC6097ST
BC9097K/BC9097ST

www.lec-commercial.co.uk 2
1 - IMPORTANT INFORMATION
Contents
1Important Information
Useful Information page 3
Unpacking page 4
Warranty page 4
Positioning page 5
Electrical Connection page 6
Safety Information page 7
Before plugging in page 8
Using Appliance for First Time page 8
Important Refrigerant Information page 8
2. Using Your Appliance
Product Details page 9
Internal Light page 10
Doors page 10
Shelves page 10
Adjusting the Feet page 10
Controller Overview page 11
Controller Operation page 12
Energy Saving Tips page 13
Storage page 13
Disposal page 13
3. Care & Maintenance of Your Appliance
Defrosting page 14
Cleaning Instructions page 15
4. Troubleshooting, Service & Repairs
Troubleshooting, Service & Repairs page 16
After Sales Support page 16
What Spares do we offer? page 16
Replacing the Door Gasket page 17
Replacing the Light Bulb page 17
Troubleshooting page 18
FAQ’s page 19
Contact Information page 20

www.lec-commercial.co.uk 3
Useful Information
We strongly recommend that you spend some time to fill in the information below and
keep it in a safe place. This will save you time if you need to contact our After Sales
team.
IMPORTANT: The Model Number, Product Code and Serial Number can all be found on
the data plate located on the interior of your appliance.
Model Number:
Product Code:
Serial Number:
Date of Purchase:
/ /
Purchased from:
...............................................................................................................................................
Please take some time to fill in the information above and keep it in a safe place.
This will save you time if you need to contact our After Sales team.
B
C
4
4
4
4
4
4

www.lec-commercial.co.uk 4
Thank you for purchasing this Lec Commercial Bottle Cooler. Whilst
unpacking, please carry out the following actions
Check the bottle cooler has not been damaged in any way during transportation.
If any damage is found, it MUST be reported to our After Sales department
immediately by calling 0844 815 3755.
When unpacking the appliance, ensure that all packaging has been removed,
including cardboard, polystyrene and any tape used to hold the shelves in place
during transportation.
The bottle cooler has been cleaned prior to dispatch; however, we advise that it
should be cleaned before use. We recommend a solution of one teaspoonful of
Bicarbonate of soda added to one litre of lukewarm water, before rinsing with
clean lukewarm water, and drying thoroughly. Alternatively, add a mild
detergent to lukewarm water and then rinse with clean lukewarm water.
When unpacking is complete, we recommend that the appliance should stand
for 2 hours to allow the refrigerant to settle.
Warranty
How to activate your Warranty
This Lec Commercial ECA approved bottle cooler comes with a 2 years Parts and Labour
warranty from the date of purchase.
Registering your product and activating your Lec Commercial warranty couldn’t be
easier. Do not hesitate to call 0844 815 3755, and after choosing the After Sales option,
one of our advisors will be happy to assist you with this.
Alternatively, you can register your product online at www.lec-commercial.co.uk.
Simply click on the ‘Our Warranty’ tab located towards the top of the page and then
choose the ‘Activate Warranty’ option from the drop down menu.
In the unlikely event of breakdown, please us on 0844 815 3755 and choose the After
Sales option for assistance.
Remember: You will need to quote the serial number of this unit. This can be found on
the dataplate on the inside of the door.
Extended Warranty
Also, we now offer customers the opportunity to purchase Extended Warranty for
added piece of mind. Details of this can be found on our website at www.lec-
commercial.co.uk or by calling our After Sales team on 0844 815 3755.

www.lec-commercial.co.uk 5
Positioning your Lec Commercial bottle cooler
When positioning your Lec Commercial Bottle cooler, please ensure you have taken
into account the following factors:
In order to conserve electricity, do not put your appliance near a source of heat,
such as a radiator. Try to avoid locations where the appliance could be exposed
to direct sunlight.
An unheated location such as a cellar is undesirable as it may cause frost build up
and slow defrosting. It may also cause excessive condensation on the outer
surface of your cabinet.
The cabinet should be placed on a hard flat surface for ventilation. The feet must
be adjusted so that the cabinet stands firm and level with a slight tilt from front
to back, to prevent any defrost water dripping from the front.
Ensure that the appliance has sufficient clearance around it to provide adequate
ventilation –10cm at each side, 6cm at the rear and 2.5cm at the top.
The internal temperature of this appliance is affected by location, room
temperature, and frequency of opening the door. The factory settings of the
electronic control (thermostat) are set to allow for these conditions. This
appliance is designed to operate in ambient temperatures between +16°C and
+38°C. Operating outside of these temperature parameters may cause the
appliance to perform out of specification.

www.lec-commercial.co.uk 6
Electrical Connection
The appliance is intended for connection with alternating current. The connection
values for voltage (V) and frequency (Hz) are declared on the name plate in the
cabinets. Power must be connected via a wall socket with a switch. It is strongly
recommended that the wall socket is accessible. The cabinet plug and wall socket should
give correct earthing. If in doubt, please contact your local supplier or an authorised
electrician.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a hazard.
If this appliance is fitted with a non-rewirable plug for which your socket is unsuitable
the plug should be cut off and an appropriate plug fitted. The removed plug must be
disposed of as insertion of the plug into an electrical socket is likely to be dangerous.
WARNING: THIS APPLIANCE MUST BE EARTHED
If a non-rewirable plug or a rewirable 13 Amp (BS 1363) plug is used it must be fitted
with a 13 Amp ASTA approved (BS 1362) fuse. If any other plug is used, please contact
our Spares department for details on appropriate fuse type.
The wires in the mains lead are coloured in accordance with the following code:
Note: These colours may not correspond with the coloured markings identifying the
terminals in your plug.
Do not push excess mains lead into the compressor compartment.
If it is necessary to change the fuse in a moulded plug and the fuse cover is detachable, it
must be refitted after the fuse has been changed. If the fuse cover is lost or damaged the
plug must not be used until a replacement is obtained.
It is important that the colour of the replacement fuse cover corresponds with the
coloured insert or as indicated in embossed words on the base of the plug. Replacement
fuse covers are available from our Spares department, at the address on the final page of
this manual.
2
GREEN AND YELLOW - EARTH
BLUE - NEUTRAL
BROWN - LIVE

www.lec-commercial.co.uk 7
Safety Information
WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in
structure, clear of obstruction.
WARNING: Do not use electrical appliances inside the compartment of the appliance,
unless they are of the type recommended by the manufacturer
Before ANY maintenance activity, carefully take the plug out of the socket by
gripping the plug, DO NOT pull on the plug cord.
DO NOT use double-wire extension cords. If an extension cord is necessary make
sure it is a cord, which possesses a protection safety certificate.
If the main power supply cord is damaged, it should be replaced by a qualified
service engineer.
DO NOT attempt to make any repairs to the appliance yourself. Repairs carried
out by someone without the relevant training are putting their personal safety at
risk and will invalidate your warranty.
DO NOT store explosive substances such as aerosol cans with a flammable
propellant in this appliance.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
IMPORTANT: this appliance can be installed built-in, without air gaps as the appliance
has been designed to gain ventilation from the front. The air ventilation at the bottom of
the cabinet must be unobstructed to allow air to circulate around the cabinet.
This appliance is intended to be used in commercial premises and similar applications
such as:
Staff kitchen areas in shops, offices and other working environments.
Bars, pubs, clubs and cafes.
Social Clubs.
Restaurants and similar.
Retail premises.

www.lec-commercial.co.uk 8
Before you plug your appliance in
IMPORTANT: Ensure that the Lec Commercial bottle cooler is left for 2 hours before
use to allow the refrigerant to settle.
It is essential that you clean the interior of your bottle cooler BEFORE using it for the
first time. The interior should be wiped with a soft cloth dampened with a solution of
one teaspoonful of Bicarbonate of soda to one litre of lukewarm water. Rinse with clean
lukewarm water, and dry thoroughly.
DO NOT use soaps, wire wool, scouring powder or disinfectants of any kind.
Using Appliance for First Time
When unpacking and cleaning are complete plug the mains lead of your appliance into a
suitable earthed socket and switch on.
IMPORTANT: When using the bottle cooler for the first time, it is essential that you
allow it to run for 24 hours before filling to ensure it is working properly.
Note: This appliance has been supplied with a factory pre-set temperature of +3°C.
Important Refrigerant Information
The entire Lec Commercial ECA bottles cooler range contains environmentally-friendly,
non ozone depleting R600a refrigerant.
WARNING: Do not damage the refrigerant circuit
As R600a is a flammable gas, it is essential to avoid damage to the refrigeration
circuit during transportation and installation. If the refrigeration circuit is damaged,
avoid using a naked flame in the vicinity of the refrigerator and connecting power to the
refrigerator. Also make sure there is good ventilation within the room.

www.lec-commercial.co.uk 9
2 - Using Your Appliance
Product Details
Model
Dimensions
W x D x H (mm)
Refrigerant
Type
Temperature
Range
Colour
No. of
Doors
Door
Style
Capacity
(330ml
bottles)
BC6097K
600 x 500 x 900
R600a
+2°C to +10°C
Black
1
Hinged
106
BC6097ST
600 x 500 x 900
R600a
+2°C to +10°C
Stainless
Steel
1
Hinged
106
BC9097K
900 x 500 x 900
R600a
+2°C to +10°C
Black
2
Hinged
180
BC9097ST
900 x 500 x 900
R600a
+2°C to +10°C
Stainless
Steel
2
Hinged
180
Note: Additional or replacement parts are also available from our Spares
department.
1. Fitted lock(s)
2. Door handle
3. Wire shelves (see page
10)
4. Adjustable front feet (x2)
(see page 10)
5. Interior Light On / Off
switch
6. Electronic controller
with external
temperature display (for
operating information see
pages 11-12)
6
1
2
5
4
3
4
5
6

www.lec-commercial.co.uk 10
Internal Light
Lec Commercial bottle coolers are fitted with internal fluorescent lights that can be
switched on and off using the red switch located at the bottom of the cabinet adjacent to
the controller.
The light should be turned off whenever it is not required, in order to save energy and
keep your running costs down.
Doors
On all ECA approved models, the door is opened by means of a handle screwed onto the
front of the door. All doors are fitted with a self closing mechanism for energy efficiency
and your convenience. Should for any reason, the self closing mechanism fail, to close
the door apply a gentle pressure until the magnetic door gasket seals against the cabinet
face.
Do not "slam close". Check periodically that there are no gaps between the gasket and
the cabinet face as this will cause the bottle cooler to operate less efficiently.
Shelves
The Bottle Cooler is fitted with adjustable shelves that can be moved to
suit your storage needs. The support clips (right) are removed by
pressing them together and tilting them upwards.
On the double door models, you will notice that there are vertical
centre rails positioned at the front and back of the interior. Ensure that
the clips are also positioned on the vertical centre rails to fully secure
shelves in place. Check that all the clips are level and at the correct
height before positioning the shelves.
WARNING: Maximum loading capacity per shelf is 20kg
Adjusting the feet
Your Lec Commercial bottle cooler comes fitted with 2 adjustable
front feet as standard. If placing on an uneven surface, you may need
to adjust the feet. Simply tilt the unit back slightly to adjust the
height.
To extend the height level of the feet, simply twist/unscrew the feet
clockwise until you reach desired level.
To reduce the height level of the feet, twist/screw the feet anti-
clockwise until you reach desired level.
6
Support clips