LEDMALL LM-LL-RGBR-0001 User manual

Product Specifications
Laser Classification
Class 2
Laser Wavelength
Blue 470nm/ Green:532nm /Red: 650-660nm
Laser MTBF
More than 5000 hours
Power Consumption
Up to 12 Watts
Power Input
120VAC (when used with supplied transformer)
Operation
Indoor / Outdoor
Operating Temperature
-20°C –35°C (-4°F –90°F)
Projection Coverage
25ft x 25ft (7.6m x 7.6m)
Maintenance
Maintenance free –no user serviceable parts
Remote Battery
23A 12V, included
Troubleshooting
Problem
Solution
Light does not come on
Check Laser Light is plugged in and
switched on at the mains. Check socket
works with an alternative electrical
product.
Remote Control does not
operate Light
Replace battery with new battery.
Try synching process again
Laser Light making
unusual noises or smells.
Switch product off immediately and
disconnect from power socket. Return
product to supplier.
Disposal of Old Electrical & Electronic Equipment (Applicable in the
European Union and other European countries with separate collection
systems)
For more detailed information about recycling of this product, please
contact your local Council, your household waste disposal service or the
shop or source where you purchased the product.
© 2014
Laser Landscape Light
LM-LL-RGBR-0001
DO NOT PLUGIN LASER LIGHT UNIT UNTIL
PROMPTED TO IN THESE INSTRUCTIONS.
WARNING: To reduce risk of injury, the user must read and
understand this instruction manual before using the Laser
Light. This machine is intended for home use only in
accordance with the instructions provided in this manual.
Please read these instructions carefully and retain for future
use
This symbol on the product or on its packaging
indicates that this product (including batteries) shall
not be treated as household waste. Instead it shall be
handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the
environment and human health, which could otherwise
be caused by inappropriate waste handling of this
product. The recycling of materials will help to
conserve natural resources.

IMPORTANT SAFEGUARDS
To reduce the risk of fire, electric shock, or injury when using any electric appliance,
precautions should be made. These precautions include but are not limited to:
Read all instructions.
CAUTION! —Use only as directed. Improper use may result in damage to the eyes due to
direct exposure to laser radiation.
This product has a polarized plug to reduce the risk of electric shock. It will therefore only fit
into a polarized outlet one way. If the plug does not fit, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not use with an extension cord unless the plug can be fully
inserted. Do not alter the plug.
This unit is certified as a Class 2 laser product by the US Federal Laser Product Performance
Standard (FLPPS) according to regulations in 21 CFR Subchapter J. Class 2 laser products
can be hazardous when directly viewed.
Avoid looking directly into Class 2 lasers. This product, as well as other demonstration laser
products like some laser pointers, are classified as Class 2 laser energy levels. This product
uses diffractive optics to scatter the beam of energy. This scattering effect causes the energy
concentration to drop below the exposure limits for momentary or accidental viewing at a
relatively short distance for the laser aperture. As with all bright light sources, when you
operate this device in public areas it is recommended that up-close access to the light be
restricted.
While the Class 2 laser in this device may be hazardous on its own, it is encased in a
protective housing and uses diffractive holographic optics, therefore the laser radiation is not
directly exposed to during operation or maintenance. Each individual laser beam is less than
5mW, which is about the same as an average laser pointer.
DO NOT attempt to open the protective housing or operate the device if the aperture
windows are damaged. If the unit requires service that involves removing the protective
housing, contact the manufacturer. Opening the protective housing voids the warranty.
Use only three-wire outdoor extension cords that have three-prong grounding plugs, plugged
into grounded outlets. Acceptable extension cord types:
SW, SW-A, SOW, SOW-A, STW, STW-A, STOW, STOW-A, SJW, SJW-A, SJOW, SJOW-A,
SJTW, SJTW-A, SJTOW, SJTOW-A
Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the circuit(s) or
outlet(s) to be used while operating portable laser light in a wet location. Receptacles with
built-in GFCI protection are available for this purpose.
SAVE THESE INSTRUCTIONS
Before You Begin
Carefully unpack package contents to make sure all parts are present
1. Light projector 2. Remote Controller
3. Power SupplyAdaptor 4. Ground Stake 5. Manual
DO NOT PLUG IN LASER UNIT UNTIL PROMPTED IN THE STEPS BELOW.
If you already have, unplug it now and follow the steps below in order.
First, install the included 23A battery in the remote. To test the remote’s
battery connection, press any button and the LED will illuminate for 1
second. If the LED does not illuminate, check to make sure you have
installed battery according to the correct polarity.
Controller
Notes:
Only use supplied transformer connected to a properly grounded
outdoor outlet.
Do not use with dimmers.
Operate in temperatures of -20°C to 30°C (-4˚F to 86˚F). There may be a
slight delay if operating below 13°C (55˚F). Please allow up to 10 minutes for
light to warm up and reach its full projection. Green laser start up time may
take up to 30 minutes in temperatures below -10°C (14˚F).
When hanging the laser light, for safety purposes it is recommended
to mount using a sturdy hanging clamp and safety cable.