Ledridge Lighting Touch P Series Instruction Manual

WWW.LEDRIDGE.CO.UK
LLTOUCHCPS
Installation & user manual
TOUCH P SERIES DMX LIGHTING
CONTROLLER
02-2015EN
Ledridge Lighting
Unit 6, 19 Highcliffe Road
Hamilton
Leicester
LE5 1TY
Tel: [phone]
www.ledridge.co.uk

Installation
ENSURE ALL POWER IS TURNED OFF
Mount an electrical box inside the wall
The Touch P Series controller can be installed in a 35mm metal electrical backbox if the you are
hardwiring the DMX and not using a data connection. You will require a 45mm metal electrical
backbox is you are using a data cable for the DMX or require a data connect.
You can only install the Touch P Series ush. If you wish to insert the AC/DC adapter inside the
backbox use a metal duel backbox.
Connect the wires
DMX Hardwire: Connect the DMX wires to the green block.
Brown = DMX Ground
Orange = DMX -
Orange and White = DMX +
OR DMX Data Cable: Connect the DMX RJ45 cable to the
DMX port of the back of the Touch P Series Controller.
Power: The power comes prewired to the green block.
Solid black = Power Ground
Black and Grey = Power +
Black & Grey
Black
Brown
Orange
Orange & White
POWER +
POWER GROUND
DMX +
DMX -
DMX GROUND
3. Place the front plate over the backplate
and slide down to x.
Mount the Touch Controller on the wall
1. Remove the back plate of the Touch
Controller by sliding down the back plate
2. Screw the Touch Controller back plate onto
the back box using 3.5mm screws.
1.1 1.2
2.1
3.1
In This Box
You should be supplied with the following:
1 x Touch P Series DMX Controller
1 x AC/DC Power adapter
1 x 5-way push on connector, prewired to power adapter.
1 x USB to Mini USB connecting cable
1 x Touch Studio Software CD
1 x 10m Data cable (RJ45) Stripped one end.
Important Information
All installations should be completed by a competent electrical professional.
You should follow all instructions as outline in this manual, failure to follow these instruction may
cause damage to yourself, property or the unit.
Ensure all mains power is turned o before you begin the installation; and remain o for the
duration of the installation.
The Touch P Series requires a 240V 2amp power supply.
Installation Continued
Once Power and/or DMX are wired to the green block, connect the green block to the back of the
Touch P Series Controller.
Connect the AC/DC power adapter to 240V 2amp power supply.

Basic Functions
SCROLL WHEEL FOR ADJUSTING /
MENU SELECTION
ON/OFF
Using multiple Touch P Series controllers
It is possible to use multiple Touch P Series controllers to control zones independently or to have
them sync with each other.
Simply connect multiple Touch P Series controllers to the same router via a data cable using the
data port on the back of the Touch P Series controllers and the Ethernet ports of the router.
NEXT SCENE
SCENE
MODE
SPEED
ADJUST
NEXT ZONE
PREVIOUS SCENE
COLOUR
ADJUST
DIMMING
ADJUST
PREVIOUS ZONE

Connecting to Software
1. Connect the Mini USB end of the supplied USB to Mini USB cable supplied to the Touch P Series
Controller.
2. Connect the USB end of the USB to Mini USB cable supplied to the computer.
3. Open the Touch Studio Lite or Touch Studio Pro software installed on your computer to edit your
scenes.
NOTE: This Mini USB port of the Touch Controller is for data transfer only, it does not provide power
output.
Touch Studio Software
The Touch P Series is compatible with the Touch Studio Lite and Touch Studio Pro software
supplied. The Touch Studio software user manual is available online, via our website at the
following link:
www.ledridge.co.uk/manual
Mobile Software
The Touch P Series is compatible with third party mobile and tablet apps available from the Apple
App Store and Android Play Store. For recommended compatible apps visit our website.
www. ledridge.co.uk/led-controllers/touch
NOTE: Third party apps require a WiFi connection and you will need to use an Ethernet data cable
connect between your router and the Touch P Series controller.
For details on third party apps features please contact the app provider.