LEDS C4 EASY RGB+ User manual

Last update 03-05-2019
1
EASY RGB+ Installation guide
Index
1- Definition and components of the EASY RGB+ system 2
2- Schematics 4
3- Cab e sections and distances between ights and the equipment 6
4- Remote contro features 7
6.1- Buttons description
6.2- Distance range
6.3- How to synchronize the remote contro
6.4- How to change the batteries

Last update 03-05-2019
2
1.-Definition and components of the EASY RGB+ s stem
The EASY RGB+ system is a non-standard protoco owned by Leds-c4 that a ows the contro of RGB fittings using on y
3 wires.
The MASTER and SLAVE controllers available onl can feed Leds-c4 fittings that come with the EASY RGB+
feature. You can check that the product comes with this feature in our general catalogue. Note that EASY RGB+
fittings are not compatible with other control protocols.
1.1.-MASTER controller:
71-E069 150W With remote control and push button on the box.
71-E011 50W With push button without remote control.
This contro er stores the co our sequences and fixed co ours and generates the RGB signa that fittings wi recieve.
Both contro ers come with an integrated push button that triggers the co our sequences. The big contro er a so
comes with a remote contro . A EASY RGB systems requires at east one Master contro er.
Co our scenes:
-8 changing co our sequences.
-Fixed co ours.

Last update 03-05-2019
3
1.2.-SLAVE controller:
71-9817-00-00 150W
It can on y be uti ized with the Master contro er 71-E069 (150W). Projects that require more than 150W a
repeater/s ave contro er has to be uti ized. This contro er copies the RGB contro signa coming from the Master
contro er and sends it to its connected fittings. The insta ation can take maximum 9 s ave repeaters.

110-240V/50-60Hz
L
x
MASTER 71-E069
...
...max 9slaves
DO NOT USE
IN EASY+
2.1-Schematics
MASTER 71-E069 150W
SLAVE 71-E070 150W
N
x
+24
-
DATA
x
x
DATA -
DATA +
x
x
x
OUTPUT INPUT
L
x
N
x
+24
-
DATA
DATA +
DATA -
DATA -
DATA +
x
x
x
OUTPUT INPUT
SLAVE 71-E070
LN
...
max150W
max150W

2.2-Schematics
MASTER 71-E011 50W
L
DO NOT USE
IN EASY+
N
+24
-
DATA
...
max50W
110-240V/50-60Hz

Last update 03-05-2019
4
3.-Cable sections and distances between lights and equipment
Next tab e shows the maximum power according to the section of the wires and the ength of the insta ation.
Maximum power to supp y every Master and/or S ave equipment according to the wiring section used in the
insta ation and the maximum distance (d) between every equipment and the ast piece.

Last update 03-05-2019
5
4.- Remote controllers:
The remote contro er is uti ized to choose a fixed co or by means of its touch whee or the co our sequences stored
in the Master contro er memory. It is a so possib e to adjust the brightness and the co our sequences speed.
4.1.-Buttons description
4.2.-Distance range
The recommended distance from the remote contro er to the master box is the 15 to 25 meters without any
obstac e.

Last update 03-05-2019
6
4.3- How to s nchronize the remote control of the Master controller 71-E069
MEMORY DELETION
1.-Turn off the power.
2.-Ho d the contro er push button (Fig.1) whi e switching on the mains. Keep on ho ding the push button unti the
fittings start f ashing in b ue co our. This means the contro er memory has been erased.
SYNCHRO
3.-Turn on the mains. Switch off the contro er by means of ho ding the contro er push button (Fig.1).
4.-Ho d down the contro er push button (Fig.1) and the top button of the remote contro (Fig.2) at the same time
unti the fittings start f ashing in green. This mean the synchronization has been done successfu y.
5.-In case the fittings don’t f ash in green repeat the steps 3 and 4. In case the synchronization fai s again check the
remote contro batteries and repeat the steps from 1 to 4.

Last update 03-05-2019
7
4.4- How to change the batteries
1.-Open the back cover.
2.-Remove the o d batteries.
3.- P ace the new batteries type 2xAAA 1.5V, A ka ine.
*Avoid mixing o d and new batteries and mixing batteries from different brands.