Lem Elettronica DSA15-5G User manual

DSA15-5G
Automatic Programming TV terrestrial multiband amplier
Installation and start-up
1_Keep (+ 5 seconds) the AUTO Programming key pressed until the LED Power start to blink red/green
2_The amplier will start the channel (MUX) search for the connected inputs and the LED Power blinking red/green will indicate that
DVB-T/T2 channels are scanned by the internal tuner-demodulator. When the search is complete and the channel are stored the LED
Power will turn to xed green.
4_The output level can be manually adjusted operating on the trimmer OUTPUT LEVEL
Programming and output level setup
Antenna remote power error
If LED POWER remains xed red there is an antenna input short circuit or over current. Please check the input(s) and
remove the issue.
Technical specications
AUTO Programmig key (to run SmartScan)
2
Output level adjuster 80... 100dBµV
1
DAB ON/OFF selector switch
14
Ground clamp
13
FM -10dB / +15dB gain level selector switch
15
Antenna input (1) BIII / DAB / UHF(E21... E48)
6
Antenna inputs (2)/(3) UHF (E21... E48)
7
MATV output /remote power 12...15VDC
10
Multi-function LED
8
Antenna input (4) FM (88... 108MHz)
9
230VAC 50/60Hz Mains input
11
(1) BIII/DAB/UHF: 174... 694MHz
(2) UHF: 470... 694MHz
(3) UHF: 470... 694MHz
(4) FM: 80... 108MHz
GAIN FM: 15dB
GAIN BIII/DAB: 40dB
GAIN UHF: 50dB
MAX OUTPUT x MUX: 100dBµV
MAX TOTAL OUTPUT: 115dBµV
DC INPUT: 230VAC/8W
SAW
FILTER
PROTECTED
AUTO-Programming
Digital Signal Processor
BIII/DAB/UHF
1
UHF
2
OUT UHF
3
FM
4
12VDC
50mA
12VDC
50mA
12VDC
50mA
POWER
DC
DAB
ON
OFF
FM
+15
dB
-10
DSA15-5G
SmartScan
Press
+5 Seconds
AUTO
Programming
100dBµV80dBµV
90dBµV
OUTPUT LEVEL
INPUTS
OUTPUT
POWER
6791011
8
1
3
4
5
2
1 Connect an earth wire to grounding clamp
2 Connect the TV aerial(s) to the amplifier’s inputs
3 Connect the MATV output and terminate the unused inputs with 75Ω loads
4 Power up the amplifier connecting the power cord to mains plug
NUMBER OF INPUTS 1xFM / 1xBIII/DAB/UHF / 2xUHF
INPUTS FREQUENCY RANGE MHz FM (80... 108)
BIII (170... 230) / DAB (170... 240)
UHF (470... 694)
LTE PROTECTION LTE 700
SINGLE CHANNEL FILTERS Up to 32
NUMBER OF CHANNEL PER FILTERS 1
MAXIMUM INPUT LEVEL dBµV FM 90 - BIII/DAB 100 - UHF 100
VHF-UHF A.C.G. RANGE dB 40 dB
DIGITAL FILTERS SELECTIVITY dB 35 @1MHz
FM GAIN dB -10/+15 (selectable)
BIII/DAB GAIN dB 40
UHF GAIN dB 50
OUTPUT LEVEL RANGE (x MUX) dBµV 80... 100 (adjustable)
RETURN LOSS IN/OUT dB >10
ANTENNA INPUT REMOTE POWER SUPPLY 12V / 60mA
INPUT VOLTAGE V230V 50/60Hz
MAXIMUM CONSUMPTION W8
OPERATING TEMPERATURE °C -15... 40
DIMENSIONS mm 135 x 91 x 45
Satellite and TV reception equipment

BIII/UHF
(1) BIII/DAB/UHF: 174... 694MHz
(2) UHF: 470... 694MHz
(3) UHF: 470... 694MHz
(4) FM: 80... 108MHz
GAIN FM: 15dB
GAIN BIII/DAB: 40dB
GAIN UHF: 50dB
MAX OUTPUT x MUX: 100dBµV
MAX TOTAL OUTPUT: 115dBµV
DC INPUT: 230VAC/8W
SAW
FILTER
PROTECTED
AUTO-Programming
Digital Signal Processor
BIII/DAB/UHF
1
UHF
2
OUT UHF
3
FM
4
12VDC
50mA
12VDC
50mA
12VDC
50mA
POWER
DC
DAB
ON
OFF
FM
+15
dB
-10
DSA15-5G
SmartScan
Press
+5 Seconds
AUTO
Programming
100dBµV80dBµV
90dBµV
OUTPUT LEVEL
INPUTS
OUTPUT
POWER
UHF
FM
UHF
MATV
230VAC
50/60Hz
2011/65 EU
LEM ELETTRONICA srl •Via Grezze, 38 •25015 Desenzano d/G •Italy Tel. [phone]
Fax. [phone] • [email protected] www.lemelettronica.it
BIII/UHF
(1) BIII/DAB/UHF: 174... 694MHz
(2) UHF: 470... 694MHz
(3) UHF: 470... 694MHz
(4) FM: 80... 108MHz
GAIN FM: 15dB
GAIN BIII/DAB: 40dB
GAIN UHF: 50dB
MAX OUTPUT x MUX: 100dBµV
MAX TOTAL OUTPUT: 115dBµV
DC INPUT: 230VAC/8W
SAW
FILTER
PROTECTED
AUTO-Programming
Digital Signal Processor
BIII/DAB/UHF
1
UHF
2
OUT UHF
3
FM
4
12VDC
50mA
12VDC
50mA
12VDC
50mA
POWER
DC
DAB
ON
OFF
FM
+15
dB
-10
DSA15-5G
SmartScan
Press
+5 Seconds
AUTO
Programming
100dBµV80dBµV
90dBµV
OUTPUT LEVEL
INPUTS
OUTPUT
POWER
UHF
FM
UHF
MATV
230VAC
PSU 12... 15VDC ≥15W
Power injector INS-02
230VAC mains supply
Coaxial powering with remote PSU
1. Do not expose the amplifier to extreme temperatures.
2. Place the amplifier in a dry and well-aired location.
3. Install the unit on a vertical wall, or in a waterproof cabinet with a minimum IP55 rating, and fix it safely.
4. Connect the power adapter cord to a detachable power supply socket.
Safety instructions
Dispose according to local authorities recycling processes
The equipment is compliant with RoHS 2011/65EU
The equipment complies with the CE requirements
Equipment grounding terminal
DESCRIPTION OF SYMBOLS AND ELECTRICAL SAFETY