less care VANITY SET LV12-60 User manual

Version 1.0
Version 1.0
www.lesscare.com
VANITY SET:LV12-60
VANITY CABINET + VANITY TOP + MIRROR
INSTALLATION INSTRUCTIONS

VANITY CABINET + VANITY TOP + MIRROR
VANITY SET:LV12-60
DIMENSIONS/TECHNICAL DATA
READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT
2 PEOPLE ARE REQUIRED TO LIFT AND DURING
ENTIRE INSTALLATION OF THIS PRODUCT
INSTALLATION OF LESSCARE PRODUCTS BY AN
INEXPERIENCED INSTALLER MAY RESULT
PERSONAL INJURY OR DEATH!
INSTRUCTIONS THAT, IF IGNORED COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED BY INCORRECT HANDLING
OR INSTALLATION OF THE PRODUCT. THESE INSTRUCTIONS MUST BE OBSERVED FOR SAFE INSTALLATION.
LessCare reserves the right to change, update, modify, alter, redesign this manual/product or its policies without prior notice!
It is your responsibility to visit website to download or contact customer service for the most updated version of the installation instructions.
LessCare shall not be liable for any injuries or property damages in connection with this product during installation or use of this product!
LessCare products must be installed by a fully insured and licensed plumber only. Installation of any LessCare product by anyone other
than fully insured and licensed plumber shall void limited warranty. LessCare recommends that such licensed plumber have experi-
ence in the installation of products.
Limited warranty is void on any commercial installation
LessCare is not responsible for local code compliance for this product. Building and plumbing codes may vary from state-to-state in
accordance to your location. LessCare is not resonsible for providing any compliance certications.
LessCare is not responsible to provide any type of certications for this product
Under no circumstances LessCare shall not be liable for any and all incidental damages sustained in connection with this product
Neither manufacture, nor distributor, nor retailer is responsible for water damage or ood caused due to use of this product.
Under no circumstances LessCare shall not be liable for any and all fees, cost of installation/reinstallation/removal, subsequent damage
or transportation in case of the product defect
Regular and proper care of the product will help to keep its apperance like new for a long time.
Follow these simple steps and rules to take care of your product.
• Use only mild detergents such as soapy water to clean the surface of the product
• Absolutely avoid using cleaning products that contain bleach or ammonia
• Only use a soft cloth material to wipe a surface of the vanity cabinets.
• Never use steel, wool, or wired brushes as they will permanently scratch the surface
• Prolonged exposure of a direct sunlight may cause discoloration of the wood nish surface
PRODUCT CARE & MAINTENANCE
www.lesscare.com Version 1.0

Silicone
Pencil /Marker
Caulk Gun
Pliers Electric Drill
with DrillBits
Stud Finder Hammer
Philips
Screwdriver
Level
Safety Glass Tape Measure
Soft Cloth
or Blank
et
TOOLS REQUIRED FOR INS TALLATION
(NOT INCLUDE D)
INSTALL ATION ACCESSORIES
Wall Anchors Screws 1 1/4"
x 4 x 4
Other tools m ay be required
Silicon
Washer
Sink
Pop-up
Mounting
Ring
Silicon Washer
Brass Nut
Rubber Washer
Tail Pipe
Vanity Base Cabinet
Ceramic Basin
Wall Mount Mirror
x 2
x 2
x 1
.
VANITY CABINET + VANITY TOP + MIRROR
VANITY SET:LV12-60
PRODUCT PACKAGE COMPONETS/TOOLS REQUIRED
P-TRAP AND POP AND POP-UP
INSTALLATION DIAGRAM
VANITY COMBINATION
MAIN COMPONENTS
www.lesscare.com 3
VANITY SET:LV12-60

Front View Side View
VANITY CABINET + VANITY TOP + MIRROR
INSTALLATION STEPS
VANITY SET:LV12-60
4
ATTENTION!
Due to manufacturing process any dimensions may have a tolerance up to 3/8". All sizes are for reference only.
It is highly recommended to pull all dimensions of actual model for installation and measuring purposes.
ATTENTION! If two or more vanity cabinets are installed next to each other there will be a
visible seam between vanity tops and between vanity cabinets or between drawer base cabinets.
www.lesscare.com
23 5/8" 12"
19 5/8"
3/5"
9 7/16"
17 3/4"
31 1/2"
23 5/8"
18 7/8"

Figure 1
Figure 2
WALL WALL
WALL WALL
5
VANITY CABINET + VANITY TOP + MIRROR
INSTALLATION STEPS
MIRROR INSTALLATION
VANITY SET:LV12-60
www.lesscare.com
VANITY SET:LV12-60
Using a tape measure find a length of the vanity
top and divide it by 2. The result of the division
will be a center of the top. Using a tape measure
find the center of the top and mark a dot on the
wall just right above theb top using a pencil.
Using a level tool find a location of a second dot
to draw a vertical line that will serve as
installation center for the Vanity.
Measure the distance between installation
brackets of the Vanity and divide it by 2. The
result of the division will be a distance between
the drawn center line and center of a drilled
holes. Mark a center of the first hole and using a
level find and mark a location for a second
hole.Using an electric drill make the holes.
See Figure 1
Apply a silicone inside each hole. Insert wall
anchors (a hammer may be needed if the holes
are too tight.) Two people lift the vanity and let
the two holes align(wall anchors and the brackets
hole on vanity)Using a Philips Screwdriver insert
the mounting screws into the wall anchors.Make
sure that the vanity is secured safely on the wall.
See Figure
2
IMPORTANT! Using a stud finder locate wooden
studs. Screws for mounting vanity must be installed in
the wooden studs to support weight of the vanity.

See Figu re 3
See Figu re 4
VANITY CABINET + VANITY TOP + MIRROR
INSTALLATION STEPS
VANITY SET:LV12-60
All LV12-60 vanity cabinets by LessCare come
pre-assembled. All door and drawer handles
are installed from the inner side of the drawer
to avoid damage during transportation. Open
the drawers to install the handles. Unscrew
every handle and install them from the outer
side of the doors and drawers. See Figure 3
Note: It is highly recommended not to use
electric drill to avoid overtightening the screws
during handle installation.
INSTALL DOOR & DRAWER HANDLES
VANITY CABINET ASSEMBLY
Prior to installation of the glass vanity top you
must apply a silicone layer by a perimeter of
the vanity base cabinet and carefully lay down
the vanity top on top of the vanity cabinet.
See Figure 4
Note (single vanity sink cabinet installation):
Vanity top is slightly wider than the actual
cabinet. Make sure that outstanding edges are
equal at left and right sides.
Apply a silicone layer on the back side of the
vanity top that will be adjacent to the wall.
Allow the silicone dry for 48 hours prior to the
first use of the vanity cabinet.
www.lesscare.com
VANITY SET:LV12-60
6

Mirror Back View
Peel-O�
Film
7
VANITY CABINET + VANITY TOP + MIRROR
INSTALLATION STEPS
MIRROR INSTALLATION
Using a tape measure find a length of the vanity
top and divide it by 2. The result of the division
will be a center of the top. Using a tape measure
find the center of the top and mark a dot on the
wall just right above theb top using a pencil.
Using a level tool find a location of a second dot
to draw a vertical line that will serve as
installation center for the mirror.
Measure the distance between installation
brackets of the mirror and divide it by 2. The
result of the division will be a distance between
the drawn center line and center of a drilled
holes. Mark a center of the first hole and using a
level find and mark a location for a second
hole.Using an electric drill make the holes.
See Figure 5
Apply a silicone inside each hole. Insert wall
anchors (a hammer may be needed if the holes
are too tight.) Using a Philips Screwdriver insert
the mounting screws into the wall anchors (do
not screw in completely as the brackets of the
mirror must hang on top of the screws.) Align
the mirror with the wall and carefully hang the
mirror on the screws. Both screw heads must be
inserted into the brackets on the mirror during
hangin process. Make sure that the mirror is
secured safely on the wall.
See Figure
6
Note:
If the brackets can not reach the screws or
the mirror is loose after hanging you need to
adjust the screws using the Philips Screwdriver.
IMPORTANT! Using a stud finder locate wooden
studs. Screws for mounting mirror must be installed in
the wooden studs to support weight of the mirror.
IMPORTANT:
At the bottom of the back side of the mirror there are two foam blocks
with adhesive surface covered by a film. Remove the film before hanging
the mirror. These blocks will stick to the wall for extra support, leveling,
and preventing from moving.
Figure 5
Figure 6
WALL WALL
VANITY SET:LV12-60
www.lesscare.com
WALL WALL

LessCare reserves the right to modify this installation instructions at any time.
It is a customer's sole resposibility to inquiry for the updates of the installation instructions.
Retain these installation instructions
for future reference!
Thank you for using
LessCare products!
www.lesscare.com
VANITY SET:LV12-60
VANITY CABINET + VANITY TOP + MIRROR
INSTALLATION STEPS
VANITY SET:LV12-60