LeuchtKraft TWIST-150LED User manual

LED Beam Moving Head
TWIST-150LED
Order No. 38.7970
INSTRUCTION MANUAL
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
www.monacor.com 02.27.06.2018
Deutsch
Hinweise fürdensicherenGebrauch
Das Gerät entspricht allen relevanten Richt-
linien der EU und trägt deshalb das -Zei-
chen.
WARNUNG Das Gerät wird mit lebensge-
fährlicher Netzspannung ver-
sorgt. Nehmen Sie deshalb
nie selbst Eingriffe am Gerät
vor und stecken Sie nichts
durch die Lüftungsöffnun-
gen. Es besteht die Gefahr
eines elektrischen Schlages.
Blicken Sie nicht für längere
Zeit direkt in die Lichtquelle,
das kann zu Augenschäden
führen.
Beachten Sie, dass schnelle
Lichtwechsel bei fotosensib-
len Menschen und Epilep-
tikern epileptische Anfälle
auslösen können!
Das Gerät muss fachgerecht
und sicher montiert werden.
Wird es an einer Stelle instal-
liert, unter der sich Personen
aufhalten können, muss es
zusätzlich gesichert werden
(z.B. durch ein Fangseil; das
Fangseil so befestigen, dass
der Fallweg des Gerätes
nicht mehr als 20cm betra-
gen kann).
•
Verwenden Sie das Gerät nur im Innen-
bereich und schützen Sie es vor Tropf- und
Spritzwasser sowie vor hoher Luftfeuch-
tigkeit. Der zulässige Einsatztemperatur-
bereich beträgt 0–40°C.
•
Stellen Sie keine mit Flüssigkeit gefüllten
Gefäße, z.B. Trinkgläser, auf das Gerät.
•
Die in dem Gerät entstehende Wärme
muss durch Luftzirkulation abgegeben
werden. Decken Sie darum die Lüftungs-
öffnungen des Gehäuses nicht ab.
•
Ziehen Sie sofort den Netzstecker aus der
Steckdose,
1. wenn sichtbare Schäden am Gerät
oder am Netzkabel vorhanden sind,
2. wenn nach einem Sturz oder Ähnli-
chem der Verdacht auf einen Defekt
besteht,
3. wenn Funktionsstörungen auftreten.
Geben Sie das Gerät in jedem Fall zur
Reparatur in eine Fachwerkstatt.
•
Ziehen Sie den Netzstecker nie am Kabel
aus der Steckdose, fassen Sie immer am
Stecker an.
•
Die Strombelastung der Netzausgangs-
buchse darf 10A nicht überschreiten.
•
Verwenden Sie für die Reinigung nur ein
trockenes, weiches Tuch, niemals Wasser
oder Chemikalien.
•
Fassen Sie das Gerät beim Transport nur
am Unterteil an. Auf keinen Fall das
Gerät am Schwenkkopf oder Dreharm
tragen.
•
Wird das Gerät zweckentfremdet, nicht
sicher montiert, nicht richtig angeschlos-
sen, falsch bedient oder nicht fach-
gerecht repariert, kann keine Haftung
für daraus resultierende Sach- oder Per-
sonenschäden und keine Garantie für das
Gerät übernommen werden.
Soll das Gerät endgültig aus dem
Betrieb genommen werden, über-
geben Sie es zur umweltgerechten
Entsorgung einem örtlichen Recy-
clingbetrieb.

2
SAFETY INSTRUCTIONS
This device has left the factory in perfect condition. In order to maintain this condition and
to ensure a safe operation, it is absolutely necessary for the user to follow the
safety instructions and warning notes written in this user manual.
If the device has been exposed to temperature changes due to environmental changes, do
not switch it on immediately. The arising condensation could damage the device.
Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be earthed.
The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual. Make
sure the power cord is never crimped or damaged by sharp edges. If this would be the
case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
During initial start-up some smoke or smell or smell may arise. This is a normal process
and does not necessary mean that the device is defective, it should decrease gradually.
Please don’t project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm distance
with wall for smooth air flow, so there should be no shelter for fans and ventilation
for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively
replaced by the manufacturer of his service agent or a similar qualified person in order to
avoid a hazard.
1
WARNING
The unit uses dangerous mains voltage. Leave servicing to skilled personnel and do
not insert anything into the air vents. Inexpert handling may result in electric shock.
IMPORTANT Install the unit safely and expertly. No guarantee claims for the unit and no liability for
any resulting personal damage or material damage will be accepted if the unit is used for
other purposes than originally intended, if it is not safely installed or not correctly
connected or operated, or if it is not repaired in an expert way.
3
2UNPACKING
Thank you for choosing our TWIST-150LED moving head light. For your own
safety, please read this manual before installing the device. This manual covers the
important information on installation and applications. Please install and operate the
fixture with following instructions. Meanwhile, please keep this manual well for future
needs.
The TWIST-150LED is made of a new type of high temperature strength of engineering
plastic and cast aluminum casing with nice outlook. The fixture is designed and
manufactured strictly following CE standards, complying with international standard
DMX512 protocol.
It’s available independently controlled and linkable with each other for operation. And
it is applicable for large-scale live performances, theater, studio, nightclubs and discos.
Please carefully unpack the TWIST-150LED when you receive the package and check
whether it is damaged during the transportation.
Please check whether the following items are included inside the box:
1x Moving Head
1x Power Cable
1x Omega Clamp
1x Instruction Manual

4
FEATURES & SPECIFICATIONS
Features
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
150W High Output White LED
50,000 hours lifespan and low power consumption
Beam Angle 6°, Outstanding sharp BEAM effect and remarkable wash effect with pure
color mixing and focus Function
High light output, 14020LUX@5M at White light
Temperature protect function, when the internal temperature is up to 40° and then the
fans begin to work, when the internal temperature is up to 70° and the brightness reduce
half.
Color Wheel: 7 colors +white, rotation with variable direction and speed
1 static Gobo Wheel: 8 gobos +white, wheel rotation and shake
1 Rotate Gobo Wheel: 6 gobos +white, wheel rotation and shake
Prism: 8-facet Prism, bi-directionally rotatable at variable speeds
High speed strobe effect with 1-25 flashers per second
Internal program available
16/14/12/10 DMX Channels USITT DMX-512
DMX 512, master-slave and sound activated controllable or auto operation
Colorful LCD display
Efficient low noise fan cooling system
POWERCON IN/OUT
3-pin XLR connectors IN/OUT
Two 1/4 turn fastening Omega Clamps
IP 20 protection rating
3
5
Specifications
Input Voltage:
Light Source:
Control Signal:
Control Channel:
AC90-260V 50/60Hz
150W High Output White LED
DMX 512, master-slave, sound activated and auto operation
16/14/12/10 DMX Channels USITT DMX-512
Power Consumption: 215VA
Dimensions:
Net Weight:
280(W)*380(H)*275(D)mm
10.6kg

6
5OPERATION INSTRUCTIONS
∙The moving head is for beam effect for on-site decoration purpose.
∙Don’t turn on the fixture if it’s been through severe temperature difference like after
transportation because it might damage the light due to the environment changes. So
make sure to operate the fixture until it is in normal temperature.
∙This light should be keep away from strong shaking during any transportation or
movement.
∙Don’t pull up the light by only the head, or it might cause damages to the mechanical
parts.
∙Don’t expose the fixture in overheat, moisture or environment with too much dust when
installing it. And don’t lay any power cables on the floor. Or it might cause electronics
shock to the people.
∙Make sure the installation place is in good safety condition before installing the fixture.
∙Make sure to put the safety chain and check whether the screws are screwed properly
when installing the fixture.
∙Make sure the lens are in good condition. It’s recommended to replace the units if there
are any damages or severe scratch.
∙Make sure the fixture is operated by qualified personnel who know the fixture before
using.
∙Keep the original packages if any second shipments is needed.
∙Don’t try to change the fixtures without any instruction by the manufacturer or the
appointed repairing agencies.
∙It is not in warranty range if there are any malfunctions from not following the user
manual to operate or any illegal operation, like shock short circuit, electronic shock, lamp
broke, etc.
4PHOTOMETRIC DATA
7
6INSTALLATIONS
Cautions: For added protection mount the fixtures in areas outside walking paths, seating
areas, or in areas were the fixture might be reached by unauthorized personnel.
Before mounting the fixture to any surface, make sure that the installation area can hold a
minimum point load of 10 items the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as an
appropriate safety cable.
Never stand directly below the device when mounting, removing, or servicing the fixture.
From a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture is kept
at least 0.5m (1.5ft) away from any flammable materials (decoration etc.).
Always use and install the supplied safety cable as a safety measure to prevent accidental
damage and/or injury in the event the clamp fails.
Mounting points: Overhead mounting requires extensive experience, including amongst
others calculating working load limits, a fine knowledge of the installation material being used,
and periodic safety inspection of all installation material and the fixture. If you lack these
qualifications, do not attempt the installation yourself. Improper installation can result in
bodily injury.
Be sure to complete all rigging and installation procedures before connecting the main power
cord to the appropriate wall outlet.
Clamp Mounting: The LED Moving Head provides a unique mounting bracket assembly that
integrates the bottom of the base, and the safety cable rigging point in one unit (see the
illustration below). When mounting this fixture to truss be sure to secure an appropriately
rated clamp to the included omega bracket using a M10 screw fitted through the center hole
of the “omega bracket”. As an added safety measure be sure to attached at least one properly
rated safety cable to the fixture using on of the safety cable rigging point integrated in the base
assembly.

8
Regardless of the rigging option you choose for your LED Moving Head, always be sure to
secure your fixture with a safety cable. The fixture providers a built-in rigging point for a safety
cable on the hanging bracket as illustrated above. Be sure to only use the designated rigging
point for the safety cable and never secure a safety cable to a carrying handle.
7DMX-512 CONTROL CONNECTIONS
9
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the
other side to the male 3-pin XLR input of the moving head. You can chain multiple moving
head together through serial linking. The cable needed should be two core, screened cable
with XLR input and output connectors. Please refer to the diagram below.
For installations where the DMX cable has to run a long distance or is in an electrically noisy
enviroment, such as in a discotheque, it is recommended to use a DMX terminator. This helps
in preventing corruption of the digital control signal by electrical noise. The DMX terminator is
simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3, which is then
plugged into the output XLR socket of the last fixture in the chain. Please see illustrations
below.

10
MENU
Address Set [Set Address Numbers]
[DMX]
Run Mode [AUTO] Auto 1- Auto2
[SOUND]
[MANUAL] Manual Test Function and Operation
Pan reverse
Tilt reverse
Display
Screen Reverse
Setup [ Advanced Setting] Channel (16/14/12/10CH Select)
Sensitivity (01-100)
Motor zero
Reset
Factory Set
Ver V1
System Information DMX Address
Temperature
8MENU OPERATIONS
11
DMX CHANNELS
16/14/12/10/ channel mode sheet
CH10 CH12 14CH 16CH Function
Channel
Value
Discription
CH1 CH1 CH1 CH1 Pan 0-255 0-540°
CH2 CH2 Pan fine 0-255 Pan Fine
CH2 CH2 CH3 CH3 Tilt 0-255 0-270°
CH4 CH4 Tilt Fine 0-255 Tilt Fine
CH3 CH3 CH5 CH5 X, Y speed 0-255 From fast to slow
CH4 CH4 CH6 CH6 LED Dimmer 0-255 From dark to bright
CH5 CH5 CH7 CH7 LED Strobe
0-7 Turn on
8-250 Strobe from slow to fast
251-255 Turn on
CH6 CH6 CH8 CH8 7 color +
White
0-15 White Light
16-31 Color 1
32-47 Color 2
48-63 Color 3
64-79 Color 4
80-95 Color 5
96-111 Color 6
112-127 Color 7
128-191 CW from slow to fast
192-255 CCW from slow to fast
CH7 CH7 CH9 CH9 8 Static Gobos
+White
0-6 Open
7-13 Gobo 1
14-20 Gobo 2
9

13
128-191 Gobo Rotate CW slow to fast
192-255 Gobo Rotate CCW slow to fast
CH9 CH11 Gobo
Rotation
0-15 open
16-95 Gobo Fine 0-360
96-135 Gobo Rotating 0-90
136-155 Gobo Rotating 0-180
156-175 Gobo Rotating 0-720
176-215 Gobo self-rotating CW
from slow to fast
216-255 Gobo self-rotating CCW rotating
from slow to fast
CH8 CH10 CH10 CH12 Focus 0-255 Gobo hazy to clear
CH9 CH11 CH11 CH13 Prism
0-63 Open
64-255 Prism In
CH10 CH12 CH12 CH14 Prism
Rotation
0-15 Stop
16-135 Rotate CW slow > fast
136-255 Rotate CCW slow > fast
CH13 CH15 self-setting
Program
0-7 No action
8-131 Auto mode
132-255 Sound mode
CH14 CH16 Reset
0-249 No function
250-253 Reset
254-255 No function
12
21-27 Gobo 3
28-34 Gobo 4
35-41 Gobo 5
42-48 Gobo 6
49-55 Gobo 7
56-63 Gobo 8
64-70 Gobo 8 shake speed from slow to fast
71-77 Gobo 7 shake speed from slow to fast
78-84 Gobo 6 shake speed from slow to fast
85-91 Gobo 5 shake speed from slow to fast
92-98 Gobo 4 shake speed from slow to fast
99-105 Gobo 3 shake speed from slow to fast
106-112 Gobo 2 shake speed from slow to fast
113-119 Gobo 1 shake speed from slow to fast
120-127 Open
128-191 Gobo Rotate CW slow to fast
192-255 Gobo Rotate CCW slow to fast
CH8 CH10 6 rotation
gobos
+White
0-15 open
16-31 Gobo1
32-47 Gobo2
48-63 Gobo3
64-79 Gobo4
80-95 Gobo5
96-127 Gobo6

14
1) All screws for installing the devices or parts of the device have to be tightly
connected and must not be corroded.
2) There must not be any deformations on the housing, color lenses, fixations and
installation spots (ceiling, suspension, trussing).
3) Mechanically moved parts must not show any traces of wearing and must not rotate
with unbalances.
4) The electric power supply cables must not show any damage, material fatigue
or sediments.
Further instructions depending on the installation spot and usage have to be adhered by
a skilled installer and any safety problems have to be removed.
In order to make the lights in good condition and extend the life time, we suggest a
regular cleaning to the lights.
1) Clean the inside and outside lens each week to avoid the weakness of the lights due
to accumulation of dust.
2) Clean the fan each week.
3) A detailed electric check by approved electrical engineer each three month, make
sure that the circuit contacts are in good condition, prevent the poor contact of
circuit from overheating.
MAINTENANCE AND CLEANING
The following points have to be considered during the inspection:
10
WARNING
The unit uses dangerous mains voltage.
Always disconnect the mains plug before cleaning.
We recommend a frequent cleaning of the device. Please use a moist, lint-free cloth.
Never use alcohol solvents.
There are no serviceable parts inside the device. Please refer to the instructions
under “Installation instructions”.
Should you need any spare parts, please order genuine parts from your local dealer.
Important Notes
The unit corresponds to all relevant direc-
tives of the EU and is therefore marked
with .
WARNING The unit uses dangerous
mains voltage. Leave servic-
ing to skilled personnel and
do not insert anything into
the air vents; inexpert han-
dling may result in electric
shock.
To prevent damage to your
eyes, never look directly
into the light source for any
length of time.
Please note that fast changes
in lighting may trigger epi-
leptic seizures with photo-
sensitive persons or persons
with epilepsy!
Install the unit safely and
expertly. If it is installed at a
place where people may walk
or sit under, it must addition-
ally be secured (e.g. by a
safty rope; fix the safety rope
so that the maximum falling
distance of the unit will not
exceed 20cm).
•
The unit is suitable for indoor use only.
Protect it against dripping water, splash
water and high air humidity. The ad-
missible ambient temperature range is
0–40°C.
•
Do not place any vessel with liquid on the
unit, e.g. a drinking glass.
•
The heat generated inside the unit must
be dissipated by air circulation; never
cover the air vents of the housing.
•
Immediately disconnect the mains plug
from the socket
1. if the unit or the mains cable is visibly
damaged,
2. if a defect might have occurred after
the unit was dropped or suffered a
similar accident,
3. if malfunctions occur.
In any case the unit must be repaired by
skilled personnel.
•
Never pull the mains cable to disconnect
the mains plug from the socket, always
seize the plug.
•
The current load of the mains output jack
must not exceed 10A.
•
For cleaning only use a dry, soft cloth;
never use water or chemicals.
•
When transporting the unit, always seize
its lower part. Never carry the unit by its
moving head or rotary arm.
•
No guarantee claims for the unit and no
liability for any resulting personal dam-
age or material damage will be accepted
if the unit is used for other purposes
than originally intended, if it is not safely
installed or not correctly connected or
operated, or if it is not repaired in an ex-
pert way.
If the unit is to be put out of oper-
ation definitively, take it to a local
recycling plant for a disposal which
is not harmful to the environment.
15