Leviton 1PF18 User manual

Flush Mount Pedestal with Internal Mounting Bracket
Cat. Nos. 1PF18 and 1PF24
INSTALLATION INSTRUCTIONS ENGLISH
PK-A3466-10-00-0A
WARNINGS:
• TO AVOID FIRE, SHOCK OR DEATH: TURN OFF POWER AT CIRCUIT BREAKER OR
FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING!
• To be installed and/or used in accordance with electrical codes and regulations.
• If you are not sure about any part of these instructions, consult an electrician.
CAUTIONS:
• Splices, if necessary, must be made with proper splicing equipment, materials or kits.
• No user serviceable components. DO NOT attempt to service or repair.
Overview
Each model can accommodate one or two conduit raceways. There are four, 7/16 in. holes on the internal mounting bracket.
They are secured to a at surface with the provided hardware. The pedestal can be used with a UL/C-UL listed (RTRT/RTRT7)
receptacle rated at 60A maximum, and a UL/C-UL listed switch (WFXV/WFXV7) rated at 60A maximum.
NOTE: All 12 in. heights are for special applications only, as they do not meet UL Standard 1773, paragraph 5.3.1.
“The distance between the marked nal grade level of the mounting post/pedestal and the lowest live part shall not be less
than 12 in." These models may be used in applications that extend the height requirement to allow for that 12 in. distance.
Examples are concrete columns, piers, and indoor installations that do not require a “3R” rating. Low voltage for communication
applications, such as data, voice, Ethernet, or speaker wiring can be located lower than the 12 in. minimum.
What Is Included
Installation
1. Remove internal mounting bracket located inside the bottom of the pedestal.
Use a 5/32 in. Allen wrench or hex drive bit to remove the four screws on the
bottom of the pedestal.
NOTE: Do NOT discard the bracket or screws, as you will re-install them in
a later step.
2. Use the supplied internal mounting bracket as a template, or use the
dimensions shown in the diagram, and drill four mounting holes.
3.83 in.
2.31 in.
3.83 in. 2.31 in.
3.46 in.
1.88 in.
1.58 in.
0.44 in.
0.44 in.
4.83 in.
2.83 in.
4.83 in.
3.33 in.
2.58 in.
4.46 in.
1PF Models 2PF Models
Can Accommodate:
Two 1 1/4 in. Conduits Can Accommodate:
Two 1 1/2 in. Conduits
WEB VERSION

© 2023 Leviton Mfg. Co., Inc. For Technical Assistance Call: 1-800-824-3005 (USA Only) or 1-800-405-5320 (Canada Only) www.leviton.com
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada ULC to the attention of the Quality
Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1-800-405-5320.
LIMITED 1 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benet of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship
under normal and proper use for one year from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option. For details visit www.
leviton.com or call 1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product
is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in
accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and tness for a particular purpose, but if any implied
warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and tness for a particular purpose, is limited to one year. Leviton
is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or prots or
delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
.
3. Install the four anchors.
4. Install the internal mounting bracket on the four anchors with four washers
and four hex nuts.
5. Pull wires to desired length.
NOTES:
• Do not fasten conduits, raceways, or cables to the pedestal. Form “S"
loops with the cables and wires to prevent stress on the wires inside the
enclosure. This ensures that the cables and wires have adequate room to
adjust for grade-level changes caused by freezing and thawing cycles, and
soil subsidence.
• Ground wires, included with the supply conductors only, connect to the
pedestal's ground terminal.
6. Install pedestal over internal mounting bracket using four (4)
1/4 in.-20 x 7/16 in. hex drive at head screws.
7. Remove device mounting plate by removing the two (2) 6-32 x 1/2 in. SS
Phillips pan head screws. Follow steps 1-3, as shown in the images below.
1. Remove the two
6-32 x 1/2 in.
SS Phillips pan
head screws.
NOTE: Save
these screws
for later.
2. Rotate top of
device mounting
plate forward,
so the top of the
insert exits the
opening rst.
Front of Pedestal 3. Pull
device
mounting
plate
through
opening,
and save
for later.
8. Terminate the wires to the receptacle, and install the device mounting plate
with the screws supplied. (The image shown below is a GFCI receptacle
and a single-gang device mounting plate.)
9. Place the wired device mounting plate into the pedestal by following steps
1-3, as shown in the images below.
NOTE: Images are shown without wires for reference only.
ᇄ
ᇄ
ᇄ
1. Place device
mounting plate
with wired
device through
the opening,
as shown.
2. Lower the device
mounting plate
with wired device
until there is
contact. Push top
of insert forward,
as shown above.
3. Attach the
device
mounting
plate
to the
pedestal
with the
two screws.
WEB VERSION