LG DLE9577SM User manual

DWG.
No.
TRIG.
DR COMPLETED
도면 DR 완료
완료일 :
LG 전자 (주)
LG Electronics Inc.
UNIT SCALE 11 mm
REVIEWEDDESIGNED
RELATED DWG.
CHECKED APPROVED
김 진 영 허 선 일 윤 주 한
06.07.05 06.07.06 06.07.06
MODELING I
T
L
E
T
APPROVED
승인자
PREPARED
시방자
DATE
년/월/일
REF. NO.
시방 번호
REV. NO.
기호
REVISION DESCRIPTION
변경 사항
1
2
3
4
RELEASING THIS DRAWING
WITHOUT PERMISSION LG
Electronics SHOULD BE
ACCUSED ACCORDING TO THE
LAWS AND COMPANY RULES.
이 도면은 LG전자의 자산으로 불법
유출시 관계법과 회사규정에 의해 처벌됨.
PDF
ILLUSTRATOR
215 215
280
3828EL3003M
MANUAL,OWNER’S
GIANT(D)-PJT
1/1
3828EL3003M
<< 주기 >>
1. 재질, 인쇄방법, 인쇄도수, 외곽치수등은 작업표에 준한다.
2. 인쇄내용, 문자크기 및 형상, 선의 굵기 등은 설계에서 제시된 FILM에 준함.
3. 외곽치수는 절단후 치수임.
4. 양산전에 설계 한도를 득할 것.
5. 본 부품에 금지물질이 포함되지 않도록 하고,
상세 내용은 LG(63)-A-5501-34를 만족할 것.
<< NOTES >>
1. Material, printing and exterier size are refer to work tables.
2. Printing, text size and line are based on LG design film.
3. Exterier size on the drawing is cutting line.
4. Before product controlled by criteria sample.
5. The part should not contain prohibited substances(Pb,Cd,Hg,Cr+6,PBB,PBDE)
and details should comply with LG standard of LG(63)-A-5501-34.
가
P/NO. 다
<FRONT>
<BACK>
나
WORK
가
BRAND
LG
-
DLE9577WM / DLG9588WM
DLE9577SM / DLG9588SM
M
나
MODEL
3828EL3003M
다
P/NO.
SNOW WHITE 100g OFFSET 인쇄
MATERIAL AND PRINTING DESCRIPTION
1 1
PRINTING DEGREE
EXTERIER INTERIER
LG MODEL 명
ENGILSH
SPANISH
LANGUAGE
68
PAGE
LGEUS
REMARK
SEC.
가
나
5
서비스센타 Call No 추가. AWCL604388 06.07.12 김진영 윤주한

DLE9577WM / DLG9588WM
DLE9577SM / DLG9588SM
Gracias por comprar una Secadora LG. Por favor lea su
manual correctamente, ya que
contiene informaciòn importante de una instalaciòn segura,
Uso y mantenimiento. Guarde el modelo y nùmero de serie y
conserve su manual para futuras referencias.
Para más información, visite nuestro sitio web http//us.lge.com
☎1-800-243-0000
para el Servicio LG (Atención al Cliente) 24 horas al día, 7 días a la semana

P/No.: 3828EL3003M
DLE9577WM / DLG9588WM
DLE9577SM / DLG9588SM
Thank you for buying an LG Dryer.
Please read your manual carefully, as it provides instructions
on safe Installation, use and maintenance.
Record the model and serial numbers,
and retain the manual for future reference.
For more information, visit our website at http://us.lge.com
☎1-800-243-0000
24 HOURS A DAY, 7 DAYS A WEEK FOR LG CUSTOMER SERVICE

PRODUCT FEATURES
TABLE OF CONTENTS
22
PART 1. SPECIFICATIONS .................................................................................................................................................................................................................3
PART 2. IMPORTANT WARRANTY AND SAFETY INSTRUCTIONS ................................................................................................................................................4
PART 3.INITIAL STEPS FOR INSTALLING YOUR DRYER ..............................................................................................................................................................7
PART 4.ACCESSORIES INSTALLATION ........................................................................................................................................................................................15
PART 5. ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYER.................................................................................................................................................17
PART 6. ELECTRICAL REQUIREMENTS FOR GAS DRYERS.........................................................................................................................................................21
PART 7. GAS REQUIREMENTS AND INSTRUCTIONS ....................................................................................................................................................................22
PART 8. EXHAUST REQUIREMENTS AND MAINTENANCE ...........................................................................................................................................................23
PART 9. OPERATING YOUR DRYER ................................................................................................................................................................................................25
PART 10. TROUBLESHOOTING GUIDE............................................................................................................................................................................................31
LG DRYER LIMITED WARRANTY......................................................................................................................................................................................................34
OUTSTANDING PERFORMANCE
Besides the large capacity, you can benefit from faster drying time, quiet operation, and energy efficiency.
STAINLESS STEEL DRUM
Stainless steel drum doesn’t rust.
ARTISTIC DESIGN
Modern front panel look and big crystal-clear glass door make your dryer stylish.
DIGITAL FABRIC CARE
Multi-Level temperature control takes better care of your clothes.
EASE OF USE
An entire selection of user-friendly functions make operating the dryer easy.
USING THE RLM (REMOTE LAUNDRY MONITOR)
The RLM monitors status of your dryer. You can plug the display unit into any power outlet in your home.
The RLM Display Unit can be purchased separately for this dryer.
ADAPTABLE CONTROL
The control panel can be in the top or bottom position to allow easy access whether side-by-side or stacked
on a washer.
ONE TOUCH SELECTIONS
To choose an option, press its button once. No need to press buttons multiple times to scroll through a list of
options.
1
2
3
4
5
6
7
8
What are Sensor Dry and Time Dry?
Your dryer provides sensor drying and time drying programs.
Sensor Dry
The dryer senses the dampness of the laundry and automatically determines the heat level and operation time. You might
see a sudden increase or decrease in operation time if the sensor determines more or less drying is required. This is not a
malfunction.
Time Dry
Use TIME DRY to select heat level and drying time manually. This can be used if clothes are not as dry as you like them
at the end of the cycle. Use TIME DRY for heavy and bulky items and thick work.

3
Part 1 SPECIFICATIONS
■Type : Electric and Gas Dryer
■Rating : Please refer to the rating label regarding detailed information.
■Size : 27 x 30.1 x 38.7 inches
■Capacity : IEC 7.3 cu.ft. (22.5 lb)
■Weight : 131 Ibs (59.4 kg)
❋ Specifications are subject to change by manufacturer.
■ ACCESSORIES
Dryer Rack
See page 27 for instructions. See page 15 for instructions. See page 16 for instructions.
Stacking Kit Pedestal
Purchased Separately
Remote Laundry
Monitor
Purchased Separately
❊ Design of pedestals is subject to
change without manafaturers notice.

The warranty for your dryer is located at the end of this manual. Warranty Service is
available by contacting your nearest LG Service Center. If this product is installed and
operated according to the instructions in this manual, LG will repair or replace any parts
defective in material or workmanship throughout the warranty period, beginning with the
date of purchase.
Warranty Restriction: If the dryer is subjected to other than single family use, all warranty
coverage is effective for only 90 days.
You will need the complete model and serial number when requesting warranty service. proof of
purchase date is required.
Use the space below to record the model number and serial number of your new LG dryer.
Model Number.
Serial Number.
Date of Purchase
❈ Staple your receipt here for convenience when contacting service.
Part 2
4
IMPORTANT WARRANTY AND SAFETY INSTRUCTIONS
SEEKING WARRANTY SERVICE
WARNING!
For your safety, the recommendations in this manual must be followed. To reduce the risk
of fire or explosion, electric shock or to prevent property damage, personal injury, or death
when using your appliance follow basic precautions.
!

5
Part 2 IMPORTANT WARRANTY AND SAFETY INSTRUCTIONS
1) Read all instructions before using the appliance.
2) Do not dry articles that have come into contact with
gasoline, dry-cleaning solvents, or other flammable or
explosive substances, as they give off vapors that could
ignite or explode.
3) Do not allow children to play on or in the appliance.
Close supervision of children is necessary when using
the appliance.
4) Before the appliance is removed from service or
discarded, remove the door to the drying compartment.
5) Do not reach into the appliance if the drum is moving.
6) Do not install or store this appliance where it will be
exposed to the weather.
7) Do not tamper with controls.
8) Do not repair or replace any part of the appliance or
attempt any servicing unless specifically recommended
in the user-maintenance instructions.
9) Do not use heat to dry articles containing foam rubber
or similarly textured rubber-like materials.
10) Clean lint screen before or after each load.
11) Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint,
dust, and dirt.
12) The interior of the appliance and exhaust duct should
be cleaned periodically by qualified service personnel.
13) Do not place items exposed to cooking oils in your
dryer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause a
load to catch fire.
14) Do not use fabric softners or products to eliminate
static unless recommended by the manufacturer of the
fabric softner or product.
15) This dryer is designed only for residential use.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of
malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance for
electric current. This appliance must be equipped with a
cord having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances.
WARNING - Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service person if you
are in doubt as to whether the appliance is properly
grounded.
Do not modify the plug provided with the appliance.
If it will not fit the outlet, have a proper outlet installed by
a qualified electrician.
This appliance must be connected to a grounded metal,
permanent wiring system or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or lead on
the appliance.
USING INSTRUCTIONS
1) Do not put overload into the drum to avoid the poor
drying and wrinkling.
2) Do not over dry fabrics such as knitted fabrics and
flannel.
3) Do not dry items such as elastic bands, plastics,
rubberized items, or sneakers that might melt or ignite
in the dryer.
4) Check the lint filter is in place.
5) Make sure the laundry is not caught when the door is
closed to prevent fabric damage.
6) Check the filter every cycle because a clogged filter is a
fire hazard and affects the efficiency of the dryer.
7) When cleaning the surface of the drum, you should use
a non-abrasive stainless steel cleaner.
8) To prevent a short circuit or penetrating moisture, make
sure the lamp cover is firmly closed.
WARNING!
To help reduce any risk of electric shock, fire, or other personal injury or property damage when
using your dryer, please exercise care and follow basic safety precautions, including the following:
!
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS

Part 2
6
IMPORTANT WARRANTY AND SAFETY INSTRUCTIONS
• Do not try to light a match or cigarette, or turn
on any gas or electrical appliance.
• Do not touch any electrical switches. Do not
use any phone in your building.
• Clear the room, building or area of all
occupants.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions carefully.
• If you cannot reach your gas supplier, call the
fire department.
To reduce the risk of fire or explosion, electric
shock, property damage, personal injury or death
when using this appliance, please follow all
instructions and information, including those in
this manual and instructions provided by your
gas supplier.
• Do not store or use any gasoline, dry-cleaning
solvents other flammable vapors or
liquids in the area surrounding this appliance.
• Do not dry anything that has ever had anything
flammable on it, even after washing.
• No washer can completely remove oil. Do not
dry any articles that have ever had any kind of
oil on them, including cooking oil.
• Articles containing foam, rubber, rubber-like
materials, plastic or similar materials should be
air dried.
• Failure to follow these instructions can result in
fire, death or serious injury.
• A qualified service person or company must
perform installation and service of this
appliance.
California Safe Drinking Water
and Toxic Enforcement Act
This act requires the governor of California to
publish a list of substances known to the state to
cause cancer, birth defects or other reproductive
harm and requires businesses to warn customers
of potential exposure to such substances.
Gas appliances can cause minor exposure to four
of these substances, namely benzene, carbon
monoxide, formaldehyde and soot, caused
primarily by the incomplete combustion of
natural gas or LP fuels.
Properly adjusted dryers will minimize
combustion. Exposure to these substances can be
minimized further by properly venting the dryer
to the outdoors.
WHAT TO DO
IF YOU SMELL GAS:
WARNING!
• Keep flammable materials and vapors, such
as gasoline, away from dryer.
• Place dryer at least 18 inches above the floor
for a garage installation.
• Failure to do so can result in death,
explosion or fire.
!
!
WARNING
!

7
Part 3 INITIAL STEPS FOR INSTALLING YOUR DRYER
76.5
30.1
The following instructions will help guide you through the initial steps of setting up your dryer for use.
Please note that every section of this manual provides important information regarding the preparation and
use of your dryer, and it is important that you review this entire manual before proceeding with any
installation or use. More detailed instructions concerning electrical connections, gas connections, and
exhaust requirements are provided in other parts of this manual.
Choose a location with a solid floor for your dryer.
Place the dryer at least eighteen inches above the
floor for a garage installation. After placing the
dryer in the desired location, please make sure that
it has the required clearances shown below. If you
are installing your dryer in a manufactured or
mobile home, please refer to STEP 9 for additional
instructions.
Certain minimum clearances are required
above, behind, and to the sides of the unit, as
shown below.Those required minimum clearances
are set forth in the picture below. Please keep the
following instructions in mind when installing in a
closet or recessed area:
• Consider allowing additional clearance for
installation and servicing.
• Wall, door and floor molding may necessitate
additional clearances.
• An additional inch of clearance is recommended to
minimize noise transfer.
• Consider space needed for companion appliances.
• For closet installations, the picture below shows the
minimum required ventilation openings for the door.
A louvered door with comparable ventilation openings
is also acceptable.
* Most installations require a minimum 51/2inches.
(14 cm) clearance behind the dryer for the exhaust
vent with elbow.
Closet-side ViewCloset Door
ventilation
hole
ventilation
hole
Closet-front View
STEP 1 Positioning the Dryer.
Leveling legs should be secured.
All four legs are stably placed on a solid and
even floor.
If dryer is not level, laundry may not tumble
properly and sensor will not detect accurate
humidity information.
When leveling, please be cautious not to injure
your fingers and toes.
If you install the dryer on the optional pedstal,
it is nessary to level with the pedestal leveling
legs.
Note
38.7”
(98.3 cm)
27”
(68.6 cm)
30.1”
(76.5 cm)
49.8”
(126.4 cm)

8
Part 3 INITIAL STEPS FOR INSTALLING YOUR DRYER
Once in position, adjust the leveling legs of the dryer
until it is level from left to right and front to back.
The leveling legs must remain firmly on the floor
and the dryer should not rock. The maximum slope
of the dryer from left to right or front to back should
not exceed 2.5 cm (1 inch). If the dryer is not level,
and if the slope exceeds 2.5 cm (1 inch), a load may
not tumble properly and internal sensors may
malfunction. Note: Other sections of this manual
also provide important information concerning the
placement of and clearances for your dryer. Please
review this entire manual before proceeding with any
installation.
The door on your dryer can be installed to open
either to the left or the right. Follow these
instructions to reverse the direction in which your
door opens:
STEP 2:
STEP 2 Procedure for
Reversing the Door
Door and latch should be aligned at the center
when closed.
Note
1
2
3

9
Part 3 INITIAL STEPS FOR INSTALLING YOUR DRYER
⚦Push the cap on the right side of control
panel.
⚧Remove the screw.
⚨Slide the control panel to the right about
an inch.
STEP 3 Procedure of Control Panel Change
1
Push the housing hook and disassemble the
panel.
2
Remove the safety cover.
1
Attach the housing of control panel until it
clicks into place.
2
Remove the plate by lifting it up slightly.
3
⚦Push the cap on the right side of lower
cover.
⚧Remove the screw.
⚨Slide the lower cover to the right about an
inch.
4
Disassemble
Assemble
WARNING!
WARNING!
!
!
• Disconnect power before servicing.
• Replace all parts and panels before operating.
• Be careful of the sharp edge on frame which makes you hurt.
• Failure to follow these instructions can result in death or electrical shock.
Housing
Hook
Frame
Control Panel Cap
Plate
Lower, Cover
Cap
Safety Cover
Housing
Frame
⚦
⚧
⚧
⚨
⚨
LG is not responsible for any damages to your
dryer incurred while a customer is changing.
Note
Be careful of dropping the control panel.
WARNING!
!
Make sure that the housing is attached correctly.
If not, the dryer may not operate.
⚦

Part 3 INITIAL STEPS FOR INSTALLING YOUR DRYER
10
Install the hooks of the plate in the holes
of the frame.
Slide the plate to the left until it clicks into
place.
7
8
Assemble
⚦Attach the panel by sliding to the left in
clicks into place.
⚧Turn the screw to the right.
⚨Close the cap.
Attach the safety cover.
4
5
⚦Attach the lower cover in the upper
position where the control panel was
removed.
⚧Tighten the screw.
⚨Push the cap.
6
Safety Cover
Put the hooks of the panel into the left side holes of
frame correctly.
Next the surface of the Ais located in the higher
place than the surface of the B.
Then, Push the panel until it is aligned three holes
on the top of the frame.
3
AB
Frame
Cap
⚦
⚧
⚨
Control Panel
Cap
⚦
⚧
LG is not responsible for any damages to your
dryer incurred while a customer is changing.
Note
WARNING!
!
Be sure the screw is properly tightened.
If it isn’t, the control panel could come off.
WARNING!
!
Be sure the screw is properly tightened.
If it isn’t the lower cover could come off.
WARNING!
!
Be sure to install the safety cover to
avoid electric shock.
⚨

11
Part 3 INITIAL STEPS FOR INSTALLING YOUR DRYER
In addition to the following warnings, please refer
to manual section on Exhaust Requirements and
Maintenance. IMPORTANT: To reduce the risk of
fire, combustion, and gas accumulation, the dryer
must be vented to the outdoors. Please follow the
instructions (and all others in this manual) very
carefully.
• Do not use plastic or thin foil duct.
• Use 4" (10.2 cm) diameter rigid or semi-rigid
metal duct (NOTE! Venting materials are not
supplied with the dryer, and you should obtain the
venting materials necessary for proper installation)
• Position the dryer such that the exhaust duct run is
as short as possible.
• Clean old ducts before installing this dryer
• The male end of each section of exhaust duct must
point away from the dryer.
• Use as few elbow joints as possible.
• Use duct tape on all duct joints.
• Insulate ductwork that runs through unheated
areas in order to reduce condensation and lint
build-up on pipe walls.
• PLEASE BE AWARE THAT FAILURE TO
EXHAUST THE DRYER CORRECTLY WILL
VOID THE DRYER’S WARRANTY.
WARNING!
• Use a heavy metal vent.
• Do not use plastic or thin foil duct.
• Failure to follow these instructions can
result in death or fire.
• Clean old ducts before installing this dryer.
!
■ ALTERNATE EXHAUST DIRECTIONS
1. Remove screw and exhaust duct.
(Use exhaust kit part #3911EZ9131X.)
2-1. Detach and remove the knockout that
matches the desired venting direction
(Right side not available on Gas Dryers)
2-2. Connect a short piece of duct to the
blower housing and attach the duct to
the base.
3-1. Insert the male end of a 4" elbow into the
female end of a short duct. Tape the joint.
3-2. Insert this assembly elbow first through the
hole in the dryer and push the female end
of the elbow onto the male end of the
blower output shaft. Tape the joint.
STEP 3 Connecting the Exhaust
and Venting System.
The exhaust must be vented to the outside.
Improper taping and incorrect installation will
cause dryer malfunction.
Note

12
Part 3 INITIAL STEPS FOR INSTALLING YOUR DRYER
(Gas dryer only). In addition to the following,
please refer to manual section on Gas Requirements
and Instructions.
1. Confirm that the type of gas available in your laundry
room is appropriate for the dryer. The dryer is prepared
for Natural Gas with a 3/8" NPT gas connection.
2. Remove the shipping cap from the gas connection at the
back of the dryer. Make sure that you don’t damage the
threads of the gas connection pipe when you remove the
shipping cap.
3. Connect the dryer to your laundry room’s gas supply
using a new flexible stainless steel connector (as noted
below, use a new stainless steel flexible connector if
allowed by your local codes).
4. Securely tighten all connections between the dryer and
your laundry room’s gas supply. Turn on your laundry
room’s gas supply and check all pipe connections (both
internal and external) for gas leaks with a non-corrosive
leak detection fluid. Refer to Part 7 (page 20)
5. For LP (Liquefied Petroleum) gas connection, refer to
this manual’s section entitled Gas Requirements and
Instructions.
1. New stainless steel flexible connector. Use this type of
connector only if allowed by local codes. Use Design AGA
Certified Connector.
2. 1/8" NPT Pipe Plug (for checking inlet gas pressure)
3. Equipment Shut-Off Valve
Installed within 6’ (1.8 m) of dryer.
4. Iron Pipe. Shorter than 20’ (6.1 m)
Use 3/8" pipe.
Longer than 20’ (6.1 m) - Use 1/2" pipe.
5. 3/8" N.P.T. Gas Connection.
Following are several warnings and instructions
concerning making the electrical connection for electric
dryers. More detailed information concerning the
electrical connection is provided in the manual section
entitled Electrical Requirements for Electric Dryer.
It is important that you thoroughly review that section
and the remainder of this manual, before taking any
steps to install or use this dryer.
1. Use only a new UL listed No. 10 (copper wire only)
three conductor power supply cord kit rated 240
Volts (minimum) 30 Amperes and labeled as suitable
for use in a clothes dryer.
2. A four-wire cord is required for manufactured
(mobile) home installations and where local codes do
not allow grounding of this appliance through
neutral.
3. Electrical Plug Connections.
4. For additional instruction on connecting the dryer to
an electrical power source, please refer to this
manual’s section on Electrical Requirements and
Electric Dryer.
2
3
5
1
4
WARNING!
• Use a new UL listed 30 amp power supply cord.
• Use a UL approved strain relief.
• Disconnect power before making electrical
connections.
• Connect neutral wire (white or center wire) to
center terminal.
• Ground wire (green or bare wire) must be
connected to green ground connector.
• Securely tighten all electrical connections
• See installation instructions for complete
instructions.
• Failure to do so can result in fire or electrical
shock.
!
STEP 4 Connection of Gas Supply
Make sure the burner orifice is proper for the type of
gas you have.
For instance, using LPG with LNG orifice will result
in death, fire or explosion. Or using LNG with LPG
nozzle will not allow the burner to ignite.
If needed, orifice conversion should be done by a
qualified service technician and mark or put the
label of the current type of orifice on the dryer.
If changing the orifice, also adjust the gas valve.
Note
Burner input requirements
If your house is located at the elevations up to
10,000 feet.
Adjusting burner input setting is not needed at this
elevation because AGA certifies this dryer will not have
any problem with the BTU rating at this altitude.
If your house is above 10,000 feet, you are required to
adjust a four percent (4%) reduction of the burner BTU
rating indicated on the model/serial rating plate.
Note
STEP 5 Electrical Plug Connections

13
Part 3 INITIAL STEPS FOR INSTALLING YOUR DRYER
Prior to the first use of this appliance, use all-
purpose cleaning products or a solution of detergent
and water, with damp cloth to remove from the
inside of the dryer drum/drying compartment any
dust or dirt that may have accumulated inside the
dryer. Plug-in your dryer after reviewing the
following parts on your dryer’s Electrical
Requirements.
Effective dryer operation requires appropriate dryer
airflow. The adequacy of the airflow can be
measured by evaluating the static pressure.
Static pressure in the exhaust duct can be measured
with a manometer, placed on the exhaust duct
approximately 2 ft. (60.9 cm) from the dryer.
Static pressure in the exhaust duct should not
exceed 5/8 inches (1.5 cm). The dryer should be
checked while the dryer is running with no load.
Confirming Heat Source in Gas Dryers
Close the door to the dryer drum/drying
compartment and, after completing all steps in this
manual for proper installation of this dryer, start the
dryer on a heat setting. After the dryer starts, the
igniter will glow red and the main burner will
ignite.
Warning: If all air is not purged from the gas line,
the gas igniter may go off before the gas and the
main burner have ignited. If this happens, the
igniter will re-attempt gas ignition after
approximately two minutes.
Confirming Heat Source in Electric Dryers
Close the door to the dryer drum/drying
compartment and, after completing all steps in this
manual for proper installation of this dryer, start the
dryer on a heat setting. The exhaust air or the
exhaust pipe should be warm after the dryer has
been operating for three minutes.
1
2
Measuring Static pressure
5/8 inches (1.5 cm)
MAXIMUM STATIC
PRESSURE IN
WATER COLUMN
STEP 6 Preparation of the Dryer. STEP 8 Dryer Airflow.
STEP 7 Confirming Heat Source
Operation.
Manometer
Exhaust Duct

14
Part 3 INITIAL STEPS FOR INSTALLING YOUR DRYER
The following instructions are applicable to
installations of the dryer in a manufactured or
mobile home. Any installation in a manufactured or
mobile home must comply with the Manufactured
Home Construction and Safety Standards Title 24
CFR, Part 32-80 or Standard CAN/CSA0Z240 MH
and local codes and ordinances. If you are
uncertain whether your proposed installation will
comply with these standards, please contact a
service and installation professional for assistance.
The following instructions apply to any installation
of the dryer in a manufactured or mobile home:
1) The electrical connection for an electric dryer
must be a 4-wire connection. More detailed
information concerning the electrical connection
is provided at the manual section entitled
Electrical Requirements for Electric Dryer
2) To reduce the risk of combustion and fire, the
dryer must be vented to the outside.
3) Electric dryers may be vented to the outside
using the back, left, right, or bottom panel.
4) Gas dryers may be vented to the outside using the
back, left, or bottom panel. Gas dryers may not
be vented to the outside using the right side panel
because of the burner housing.
5) The dryer exhaust duct must be affixed securely
to the manufactured or mobile home structure,
the exhaust duct must be made of a material that
will resist fire and combustion, and it is
recommended that you use a rigid or flexible
metal pipe.
6) DO NOT connect the exhaust duct with any other
duct, vent, chimney, or other exhaust duct.
7) Make sure the dryer has adequate access to
outside fresh air to ensure proper operation. The
opening for outside fresh air must be at least 25
in2(163 cm2).
8) It is important that the clearance of the duct from
any combustible construction be at least 2 inches
(5 cm), and, when venting the dryer to the
outdoors, the dryer can be installed with a
clearance of 1 inch at the sides and back of the
dryer.
9) Please be aware that venting materials are not
supplied with the dryer. You should obtain the
venting materials necessary for proper
installation.
WARNING!
DO NOT connect exhaust ducts with
metal screws or fasteners that extend
into the duct.
!
WARNING!
DO NOT vent the exhaust duct under the
manufactured or mobile home.
!
STEP 9 Additional Instructions
for Installation of Your
Dryer in a Manufactured
or Mobile Home.

15
Part 4 ACCESSORIES INSTALLATION
To ensure safe and secure installation, please
observe the instructions below.
Place washer firmly on a stable, even and
solid floor.
Peel protective paper off the tape from the
stacking kit side bracket.
Fit the stacking kit side bracket firmly to the
side of top plate by attaching the double-
sided tape to top plate as picture shows.
Secure stacking kit side bracket to the
washer with a screw on the back of bracket.
Repeat Steps 2, 3, 4 for the other side.
Place the dryer on top of the washer by fitting
legs as shown in the picture. Avoid finger
injuries - be careful not to pinch fingers
between the washer and dryer. Slide dryer
slowly backwards to the stopper of kit.
Insert the front rail. Push the front rail back
to the stoppers of side stacking kit.
Attach both sides of the front kit with screws.
• Do not use stacking kit with a gas dryer in potentially
unstable conditions like a mobile home.
Stacking kit
1
2
3
4
5
6
7
Stacking Kit Installation Instructions
Clean the surface before attaching the brackets
and double-sided tape.
WARNING!
!
Note
Incorrect Installation can cause serious
accidents.
The weight of the dryer and the height of
installation makes the stacking procedure
too risky for one person. This procedure
should be performed by 2 or more
experienced service personnel.
WARNING!
!
Do not stack a washer on the top of the dryer.
Dryer
Washer

Part 4
16
ACCESSORIES INSTALLATION
Pedestal Installation Instructions




for washer/
combo
for dryer
for washer/
combo
for dryer




3
1 4
5
6
7
2
1) Shut off gas.
2) Unplug power cord.
3) Disconnect gas line from dryer.
4) Pull away and loosen vent clamp.
5) Disconnect venting.

17
Part 5 ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYERS
The following are additional instructions regarding electrical connections and requirements for electric dryers.
Important Warning: To help prevent fire, electric shock, serious injury or death, the wiring and grounding
must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70 and all applicable local
regulations. Please contact a qualified electrician to check your home’s wiring and fuses to ensure that your home
has adequate electrical power to operate the dryer.
120V/ 240V, 60 Hertz, 3-Wire Installation
!
Instructions for Grounding of your Electric
Dryer:
a) This dryer must be connected to a grounded
metal, permanent wiring system or an
equipment-grounding conductor must be run
with the circuit conductors and connected to the
equipment-grounding terminal or lead on the
dryer.
b) The dryer has its own terminal block that must
be connected to a separate 60 Hertz single
phase AC circuit, fused at 30 Amperes (the
circuit must be fused on both sides of the line).
ELECTRICAL SERVICE FOR THE DRYER
SHOULD BE OF MAXIMUM RATE
VOLTAGE LISTED ON THE NAMEPLATE.
DO NOT CONNECT DRYER TO 110, 115,
OR 120 VOLT CIRCUIT. Heating elements are
available for field installation in dryers which
are to be connected to electrical service of
different voltage than that listed on nameplate.
c) If branch circuit to dryer is fifteen feet (4.50 m)
or less in length, use U.L. (Underwriters
Laboratories) listed No. 10 A.W.G. wire (copper
wire only), or as required by local codes. If over
fifteen feet (4.50 m), use U.L. (Underwriters
Laboratories) listed No. 8 A.W.G. wire (copper
wire only), or as required by local codes. Allow
sufficient slack in wiring so dryer can be moved
from its normal location when necessary.
d) The power cord (pigtail) connection between
wall receptacle and dryer terminal block IS NOT
supplied with dryer. Type of pigtail and gauge of
wire must conform to local codes and with
instructions mentioned on the following pages.
e) The method of wiring the dryer is optional and
subject to local code requirements. Refer to
examples on next page.
f) You must select the method by which to wire
your dryer according to local code and ordinance
requirements. Sample methods are included in
the following pages.

18
Part 5 ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYERS
Use the instructions in this section if your home has
a 3-wire receptacle (NEMA type 10-30R) and you
will be using a UL listed, 120/240 volt minimum,
30 amp, dryer power supply cord.
Review the following options to determine the appropriate electrical connection
for your home:
If this type is available at your home. you will be
connecting to a fused disconnect or circuit breaker
box.
Important : Grounding through the neutral conductor
is prohibited for (1) new branch-circuit installations,
(2) mobile homes, (3) recreational vehicles, and (4)
areas where local codes prohibit grounding through the
neutral conductor.
Prepare minimum 5 ft (1.52 m) of length in order for
dryer to be replaced.
First, peel 5 inches (12.7 cm) of covering material from
end. Strip 5 inches of ground wire insulation. After
cutting 11/2inch (3.8 cm) from 3 other wires peel
insulation back 1 inch (2.5 cm). Make ends of 3 wires a
hook shape.
Then, put the hooked shape end of the wire under the
screw of the terminal block (hooked end facing to the
right) and pinch the hook together and screw tightly.
Use the instructions in this section if your home has
a 4-wire receptacle (NEMA type 14-30R) and you
will be using a UL listed, 120/240 volt minimum,
30 amp, dryer power supply cord.
If this type is available at your home. you will be
connecting to a fused disconnect or circuit breaker
box.
1. Connect neutral wire (white) of power cord to center
terminal block screw.
2. Connect red and black wires to the left and right
terminal block screws.
3. Connect ground wire (green) of power cord to external
ground screw and move neutral ground wire of
appliance and connect it to center screw.
4. Make sure that the strain relief screw is tightened.
Be sure that all terminal block nuts are on tight and
power cord is in right position.
3-wire direct
4-wire receptacle
(NEMA type14-30R)
3-wire receptacle
(NEMA type10-30R)
4-wire direct
4-wire connection : Direct wire
• Connect the power supply wire to the terminal
block. Colored wire should be connected to
same color screw. Wire color indicated on
manual is connected to the same color screw in
block. Otherwise,a short or excessive current
flow may result.
Note