Miele PT 7186 EL User manual

11.09 Mat. No. 07 738 250 / 01
Installation recommendations
Tumble dryers
PT 7186 EL
en - GB

Mat. No. 07 738 250 / 01
2
It is essential to read the operating and installation instructions before
installing, commissioning or using the machine.
This avoids the risk of accidents or damage.
All rights reserved

Technisches Datenblatt / Technical datasheet: PT 7186 EL
Datum / Date: 28.10.2009 Seite / Page: 8
Technical Datasheet
Tumble dryer:
Heating:
PT 7186
Electric (EL)
Legend:
Circled, bold-type abbreviations:
Connection required
Abbreviations surrounded by broken circle:
Connection optional or required, depending on model
Optional extras:
UM
Miele plinth
UO 6008 (UO = Open plinth)
Height
mm
305
Width
mm
680
Depth
mm
679
UG 6008 (UG = Closed plinth)
Height
mm
305
Width
mm
692
Depth
mm
685
US 6008 (US = Plinth with drawer)
Height
mm
320
Width
mm
692
Depth
mm
685
BS
Concrete plinth
Concrete plinth (min. quality C12/15)
Recommended height
mm
300
Minimum height
mm
70
Recommended width
mm
≥700
Recommended depth
mm
≥700
It must be ensured that the concrete plinth is anchored to the
floor!
Machine connections:
Electrical
connection
1. Standard voltage (as supplied)
V
3N AC 400
Frequency
Hz
50
Rated load
kW
8.5
Fuse rating
A
3 × 16
Connection cable cross-sectional area
mm²
5 × 1.5
Connection cable length
mm
2170
Connection cable without plug
(supplied as standard)
Country variations:
1. Standard voltage (as supplied)
V
1N AC 230 -240
Frequency
Hz
50
Rated load
kW
5.78 –6.24
Fuse rating
A
1 × 25
Connection cable cross-sectional area
mm²
3 × 2.5
Connection cable length
mm
2000
Connection cable without plug
(supplied as standard)
1. Standard voltage (as supplied)
V
3 AC 230
Frequency
Hz
50
Rated load
kW
8.5
Fuse rating
A
3 × 25
Connection cable cross-sectional area
mm²
4 × 2.5
Connection cable length
mm
2000
Connection cable without plug
(supplied as standard)

Technisches Datenblatt / Technical datasheet: PT 7186 EL
Datum / Date: 28.10.2009 Seite / Page: 9
Non-standard voltages:
OS 440
1. Standard voltage (as supplied)
V
3 AC 440
Frequency
Hz
60
Rated load
kW
8.5
Fuse rating
A
3 × 16
Connection cable cross-sectional area
mm²
4 × 1.5
Connection cable length
mm
2000
Connection cable without plug
(supplied as standard)
Electrical connection must be in accordance with local and
national regulations.
Plug and socket connection in accordance with IEC/EN
60309 and IEC/EN 60947 recommended to facilitate
electrical safety tests.
If the machine is connected via a fixed connection, a multi-
pole switch must be provided on site to ensure complete
isolation. Switches with a contact opening of more than 3 mm
should be used. Such switches are, e.g., LS switches, fuses
and contactors (IEC/EN 60947).
A wall socket or mains isolator must be visible and accessible
after installation.
A new connection, modification of an existing installation or
earth checking, including the determination of suitable fuse
rating, may only be carried out by a suitably qualified
electrician in accordance with all local and national
regulations.
Vented
Nominal air throughput in vented mode
m³/h
320
Max. pressure loss
Pa
420
Max. exhaust air/gas temperature
°C
80
Connection sleeve on machine (inner diameter)
mm
100
Connection diameter on site (outer diameter)
mm
100
Connection adapter Miele Mat. no. 6595070 (inner diameter
100 mm) for flexible aluminium duct and adapter piece Miele
Mat. no. 915051 (outer diameter 110 mm) for connection to
normal heat-resistant plastic ducting are supplied as
standard.
As relative humidity in ducting can be as high as 100%,
suitable measures must be taken to prevent a backflow of
condensate into the machine.
Air intake
Standard connection:
Air intake from installation site
Recommended air intake vent cross-sectional area
(to prevent draughts in installation site)
cm²
237
Sufficient air intake should be available to replace displaced
volume of air.

Technisches Datenblatt / Technical datasheet: PT 7186 EL
Datum / Date: 28.10.2009 Seite / Page: 10
Fittings
(supplied)
Miele plinth UG/UO 6008
4 × fasteners (to secure machine to plinth)
4 × screws DIN 571 (Ø × length)
mm
8 × 65
4 × rawl plugs (Ø × length)
mm
12 × 60
Machine must be bolted to the floor!
Fixing materials for floating screed floor to be provided on site
Miele plinth US 6008
4 × fasteners (to secure machine to plinth)
4 × screws DIN 571 (Ø × length)
mm
6 × 50
4 × rawl plugs (Ø × length)
mm
8 × 40
Machine must be bolted to the floor!
Fixing materials for floating screed floor to be provided on site
On concrete plinth
2 × metal brackets
mm
6 × 50
2 × screws DIN 571 (Ø × length)
mm
8 × 40
2 × rawl plugs (Ø × length)
Machine must be bolted to the floor!
Fixing materials for floating screed floor to be provided on site
Machine data
Machine width
mm
700
Machine depth
mm
763
Machine height
mm
1020
Casing width
mm
692
Casing depth
mm
690
Min. access width to installation site
mm
720
Minimum rear wall gap (measured to front of machine)
mm
1100
Minimum wall gap (to front edge of machine)
With an installation with the minimum gap, additional work
may be required when service or repair work is necessary.
mm
900
Net weight
kg
77
Dynamic floor load, max.
N
1000
Static floor load, max.
N
Not yet available
Average heat dissipation
(dependent on ambient room temperature and programme
selected)
W
450
Sound pressure level (re 20 mPa),
(measured at a distance of 1 m from the machine and at a
height of 1.6 m)
dB (A)
<70
Installation should only be carried out by authorised fitters in accordance with valid regulations!
Observe installation instructions when installing machine! All rights reserved! Dimensions in mm