LG E1951S User manual

лчиттничюнльтцию.
глтчн.Бзвыдны
www.sotmarket.ru
дбняинфмциятв,
тзывы,бзыиы
Инструкция для
LG E2251T
Перейти в карточку товара
8 800 775 98 98

www.lg.com
OWNER’S MANUAL
LED LCD MONITOR
Please read this manual carefully before operating
your set and retain it for future reference.
LED LCD MONITOR MODELS
ENGLISH
E1951T
E2051T
E2251T
E2351T
E1951S
E2051S
E2251S
E2251VR
E2351VR
E2251VQ
E2351VQ

2
ENG
ENGLISH
TABLE OF CONTENTS
CONTENTS
3 ASSEMBLINGANDPREPAR-
ING
3 Unpacking
4 Partsandbuttons
6 SettinguptheMonitorset
6 - AttachingtheStandBase
6 - DetachingtheStandBase
6 - DetachingtheStandBody(Usingthe
Wallmount)
7 - Mountingonatable
9 - Mountingonawall
10 USINGTHEMONITORSET
10 ConnectingtoaPC
10 - D-SUBconnection
11 - DVI-Dconnection
12 - HDMIconnection
13 CUSTOMIZINGSETTINGS
13 AccessingTheMainMenus
14 CustomizingSettings
14 - MenuSettings
15 - SUPERENERGYSAVINGSettings
16 - SUPER+RESOLUTIONSettings
16 - VolumeSettings(Onlysupportedin
HDMI)
17 - DUALMONITORSettings
17 - DUALWEBSettings
18 TROUBLESHOOTING
20 SPECIFICATIONS
25 PresetModes(Resolution)
25 - D-SUB/DVITiming
26 - HDMITiming
26 Indicator
27 PROPERPOSTURE
27 ProperpostureforusingtheMonitorset.

3
ENG
ENGLISH
ASSEMBLING AND PREPARING
ASSEMBLINGANDPREPARING
Unpacking
Checkyourproductboxforthefollowingitems.Ifthereareanymissingaccessories,contactthelocal
dealerwhereyoupurchasedyourproduct.Theillustrationsinthismanualmaydifferfromtheactualproduct
andaccessories.
 Donotuseanyunapprovedaccessoriestoensurethesafetyandproductlifespan.
 Anydamagesorinjuriesbyusingunapprovedaccessoriesarenotcoveredbythewarranty.
 Theaccessoriessuppliedwithyourproductmayvarydependingonthemodel.
 Productspecificationsorcontentsinthismanualmaybechangedwithoutpriornoticeduetoupgrade
ofproductfunctions.
 Usershoulduseshieldedsignalinterfacecables(RGBcable/DVI-Dcable)withferritecoresto
maintainstandardcompliancefortheproduct.
CAUTION
NOTE
StandBase
CD(Owner'sManual)/
Card
D-SUBCable
(Thissignalcablemaybeattached
tothisproductbeforeshippingout.)
DVI-DCable
(Thiscableisnotincludedinall
countries.)
PowerCord AC-DCAdapter

4
ENG
ENGLISH
ASSEMBLING AND PREPARING
HDMI
D-SUBDVI-D
DC-IN /
䏳㵎幑‣D-SUBDVI-D
DC-IN /
䏳㵎幑‣D-SUB
DC-IN /
䏳㵎幑‣Partsandbuttons
PowerIndicator
 LightingOn:Turnedon
 LightingOff:Turnedoff
Connectionpanel(Seep.10)
Button("CUSTOMIZING
SETTINGS"onpage13)
(PowerButton)
E2251VQ
E2351VQ
E2251VR
E2351VR
䏳㵎幑‣䏳㵎幑‣䏳㵎幑‣
E2251T
E1951T
E2351T
E2051T
E1951S E2051S E2251S

5
ENG
ENGLISH
ASSEMBLING AND PREPARING
Button Description
MENU Accessesthemainmenus.(Seep.14)
LeftFirstButton OSDLOCKED/
UNLOCKED
Thisfunctionallowsyoutolockthecurrentcontrolsettings,so
thattheycannotbeinadvertentlychanged.
PressandholdtheLeftFirstButtonforseveralseconds.
Themessage"OSDLOCKED"shouldappear.
YoucanunlocktheOSDcontrolsatanytimebypushingthe
LeftFirstButtonforseveralseconds.Themessage"OSD
UNLOCKED"shouldappear.
SUPER+RESOLUTION UsethisbuttontoenterSUPER+RESOLUTIONmenu.Formoreinformation.(Seep.16)
DUAL UsethisbuttontoenterDUALmenu.
Formoreinformation.(Seep.17)
AUTO Whenadjustingyourdisplaysettings,alwayspresstheAUTObuttonontheMONITOR
SETUPOSD.(OnlysupportedinAnalogMode)
Thebestdisplaymode
E1951S/E1951T 1366x768
E2051S/E2051T 1600x900
E2251S/E2251T
E2251VR/E2251VQ
E2351T/E2351VR
E2351VQ
1920x1080
VOLUME(OnlyHDMImode) AdjustthevolumeoftheMonitorset.(Seep.16)
E2251VR/E2351VR/E2251VQ/E2351VQ
INPUT Youcanchoosetheinputsignal.

Whentwoinputsignalsareatleastareconnected,youcanselecttheinputsignal
(D-SUB/DVI/HDMI)youwant.

Whenonlyonesignalisconnected,itisautomaticallydetected.Thedefaultsettingis
D-SUB.
EXIT ExittheOSD(OnScreenDisplay).
(PowerButton) Turnsthepoweronoroff.
PowerIndicator Thepowerindicatorstaysblueifthedisplayisrunning
properly(OnMode).IfthedisplayisinSleepMode,thepower
indicatorblinksblue.

6
ENG
ENGLISH
ASSEMBLING AND PREPARING
DetachingtheStandBody(Using
theWallmount)
1 Remove2screwsandpullouttheHingeCover
fromtheMonitorset.
SettinguptheMonitorset
AttachingtheStandBase
1 PlacetheMonitorsetwiththescreenside
downonaflatandcushionedsurface.
Layafoammatorsoftprotectivecloth
onthesurfacetoprotectthescreenfrom
damage.
 Thisillustrationdepictsthegeneralmodelof
connection.Yourmonitormaydifferfromthe
itemsshowninthepicture.
 Donotcarrytheproductupsidedown
holdingonlythestandbase.Theproduct
mayfallandgetdamagedorinjureyour
foot.
CAUTION
CAUTION
DetachingtheStandBase
1 PlacetheMonitorsetwiththescreenside
downonaflatandcushionedsurface.
2 Turnthescrewtotheleft,andthenpulloutthe
StandBasefromtheStandBody.
2 AttachtheStandBaseintotheMonitorsetby
turningtheScrewtotheright.
StandBody
StandBase

7
ENG
ENGLISH
ASSEMBLING AND PREPARING
3 PressPowerbuttononthefrontswitchofpanel
toturnthepoweron.
Mountingonatable
1 LiftandtilttheMonitorsetintoitsupright
positiononatable.
Leavea10cm(minimum)spacefromthewall
forproperventilation.
10 cm
10 cm
10 cm
10 cm
Disconnectthepowercordfirst,andthenmove
orinstalltheMonitorset.Otherwiseelectric
shockmayoccur.
CAUTION
2 ConnecttheAC-DCAdapterandPowerCord
toawalloutlet.
䏳㵎幑‣
DC-IN /
䏳㵎幑‣2Remove4screwsandpullouttheStandBody
fromtheMonitorset.

8
ENG
ENGLISH
ASSEMBLING AND PREPARING
Mountingonawall
Forproperventilation,allowaclearanceof10cm
oneachsideandfromthewall.Detailed
instructionsareavailablefromyourdealer,seethe
optionalTiltWallMountingBracketInstallationand
SetupGuide.
10 cm
10 cm
10 cm
10 cm
UsingtheKensingtonsecuritysystem
TheKensingtonsecuritysystemconnectoris
locatedatthebackoftheMonitorset.Formore
informationofinstallationandusing,refertothe
TheKensingtonsecuritysystemisoptional.
Youcanobtainitfrommostelectronicsstores.
NOTE
Whenyouadjusttheangle,donotholdthe
bottomoftheMonitorsetframeasshownon
thefollowingillustration,asmayinjureyour
fingers.
Donottouchorpressthescreenwhen
adjustingtheangleofthemonitor.
WARNING
Tiltfrom+15to-5degreesupordowntoadjust
theangleoftheMonitorsettosuityourview.
NOTE
Front Rear
15- 5
manualsuppliedwiththeKensingtonsecurity
systemorvisit http://www.kensington.com .
ConnecttheKensingtonsecuritysystemcable
betweentheMonitorsetandatable.

9
ENG
ENGLISH
ASSEMBLING AND PREPARING
 Disconnectthepowercordfirst,andthen
moveorinstalltheMonitorset.Otherwise
electricshockmayoccur.
 IfyouinstalltheMonitorsetonaceilingor
slantedwall,itmayfallandresultinsevere
injury.
 UseonlyanauthorizedLGwallmount
andcontactthelocaldealerorqualified
personnel.
 Donotovertightenthescrewsasthismay
causedamagetotheMonitorsetandvoid
yourwarranty.
 Useonlyscrewsandwallmountsthat
meettheVESAstandard.Anydamages
orinjuriesbymisuseorusinganimproper
accessoryarenotcoveredbythewarranty.
 UsethescrewsthatarelistedontheVESA
standardscrewspecifications.
 Thewallmountkitwillincludeaninstallation
manualandnecessaryparts.
 Thewallmountbracketisoptional.Youcan
obtainadditionalaccessoriesfromyourlocal
dealer.
 Thelengthofscrewsmaydifferdepending
onthewallmount.Besuretousetheproper
length.
 Formoreinformation,refertothe
instructionssuppliedwiththewallmount.
CAUTION
NOTE
Model E1951S
E2051S
E2251S
E1951T
E2051T
E2251T
E2351T
E2251VR
E2351VR
E2251VQ
E2351VQ
VESA(AxB) 75x75
Standardscrew M4
Numberofscrews 4
Wallmountbracket
(optional)
RW120
IfyouintendtomounttheMonitorsettoawall,
attachWallmountinginterface(optionalparts)to
thebackoftheset.
WhenyouinstalltheMonitorsetusingthewall
mountinginterface(optionalparts),attachit
carefullysoitwillnotdrop.
1 Please,Usethescrewandwallmountinterface
inaccordancewithVESAStandards.
2 Ifyouusescrewlongerthanstandard,the
monitormightbedamagedinternally.
3 Ifyouuseimproperscrew,theproductmightbe
damagedanddropfrommountedposition.In
thiscase,LGElectronicsisnotresponsibleforit.
4 VESAcompatibleonlywithrespecttoscrew
mountinginterfacedimensionsandmounting
screwspecifications.
5 PleaseuseVESAstandardasbelow.
 784.8mm(30.9inch)andunder
*WallMountPadThickness:2.6mm
*Screw:4.0mmxPitch0.7mmx
Length10mm
 787.4mm(31.0inch)andabove
*PleaseuseVESAstandardwallmountpad
andscrews.
A
B
 VESA(AxB)