LG PWMT300 Guide

Model: PWMT300
Features:
• Forflatpanelscreens
• One-touchtilt for effortless positioning and adjustment of the screen
• Ultra-slim design holds the screen flat against the wall
• IncreLok™ locking tilt positions for specific tilt settings in 5° increments
• BLACK. Scratch resistant fused epoxy finish.
• Mounts to wood studs, concrete, or to cinder blocks
NOTE: Not for use with metal studs
Max UL Load Capacity 250lb (113.5kg)
Installation and Assembly:
Universal Wall Mount
This product is UL Listed. It must be
installed by a qualified professional
installer.
R
ISSUED: 12-15-06 SHEET #:202-9189-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
1 of 14
PWMT300

ISSUED: 12-15-02 SHEET #:202-9189-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
2 of 14
Note: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
•studfinder("edge to edge" stud finder is recommended)
•drill
•1/4" bit for concrete and cinder block wall
•5/32" bit for wood stud wall
•level
•7/16" socket or crescent wrench
•tapemeasure
Table of Contents
Parts List..............................................................................................................................................................................3
Adjusting Tilt Brackets..........................................................................................................................................................4
InstallingTilt Brackets...........................................................................................................................................................5
Installation to Double Wood Stud Wall..................................................................................................................................7
Installation to Triple Wood Stud Wall ....................................................................................................................................8
Installation to Solid Concrete or Cinder Block .......................................................................................................................9
MountingandRemovalofFlatPanelScreen.......................................................................................................................10
ScreenCompatibilityChart ................................................................................................................................................. 11
Forcustomer care call [phone] or [phone].
• Do not begin to install this mount until you have read and understood the instructions and warnings contained in this
InstallationSheet. If you have any questions regarding any of the instructions or warnings, please call Peerless
customercare at1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Makesurethat the supporting surface will safely support the combined load of the equipment and all attached hard-
wareand components.
• Neverexceed the Maximum ULLoadCapacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an
"edgeto edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly,but donotovertighten. Overtightening can damage theitems,greatly reducing their holding
power.
WARNING

ISSUED: 12-15-02 SHEET #:202-9189-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
3 of 14
Parts may appear slightly different than illustrated.
HH
Parts List Black Silver
Description Qty. Part # Part#
AA wall plate 1 201-1210 201-4210
BB left tilt bracket 1 201-0181 201-0192
CC right tilt bracket 1 201-0177 201-0193
DD #14 x 2.5 wood screw 6 5S1-015-C03 5S1-015-C03
EE alligator® anchor 6 590-0097 590-0097
FF 1/4 serrated flanged locknut 4 530-1021 530-1021
GG wing bracket 2 201-1134 201-4134
HH M5 x 25mm security screw 2 520-1122 520-1122
II wrench 1 560-1146 560-1146
Before you begin, make sure all parts shown are included with your product.
Parts may appear slightly different than illustrated.
DD
AA
CCBB
bottomextension bracket
top extension bracket
M4 x 12 mm (6)
(504-9013)
Adapter Bracket Fasteners
M4 x 25 mm (4)
(504-1015)
M5 x 12 mm (4)
(520-1027) M5 x 25 mm (4)
(520-9543)
M6 x 12 mm (4)
(520-1128)
M5 x 40 mm (6)
(520-1199)
M4 x 8 mm (6)
(520-1237)
M6 x 16 mm (6)
(520-9274)
multi-washer(6)
(580-1036)
I.D. 8.7 mm (4)
(540-1059)
I.D. 5.6 mm (4)
(540-1057)
M8 x 25 mm (4)
(520-1031) I.D. 6.4 mm (6) (590-1106)
M8 x 16 mm (6)
(520-9257)
GG
Security Option
NOTE: Replace safety screw in each tilt bracket
with M5 x 25 security screw (HH) using
wrench (II).
EE II
FF

ISSUED: 12-15-02 SHEET #:202-9189-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
4 of 14
Loosenfour1/4-20x1/4"screwsoneachadapterbracket(BB,CC). Position extension brackets, with slots
facing downward, onto adapter brackets (BB,CC) at the appropriate position to accommodate your screen as
shown in Figure 1.1. Securely tighten all 1/4-20 x 1/4" screws as shown in figure 1.2.
NOTE: In all bracket extension positions, stops and 1/4-20 x 1/4" screws must be engaged in slots as shown in
figure1.2.
BB,CC
1/4-20 x 1/4"
SCREWS
BOTTOM
EXTENSION
BRACKET
TOP
EXTENSION
BRACKET
Adjustment of Extension Brackets
fig 1.1 fig 1.2
BB,CC
TIGHTEN
FASTENERS
STOP
STOP
ADAPTER
BRACKET
Make sure
slotsface
downward.

ISSUED: 12-15-02 SHEET #:202-9189-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
5 of 14
n
Installing Tilt Brackets
Refer to Screen Compatibility Chart to determine the proper fasteners to use.
NOTE: Referto page 4 for adjustments of top extensionbracket.
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place
screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached.
Place tilt brackets (BB and CC) on back of screen.Align to holes, and center on back of screen as shown in figure
2.1.Attach the tilt brackets to the back of the screen using the appropriate combination of screws, multi-washers, and
spacers as shown in figure 2.3. NOTE: Be sure to attach tilt brackets with knobs facing outward as in figure
2.1.
NOTE:Top and bottom mounting holes must be used for attaching brackets. Middle holes should also be used where
thefasteners and screens allow.
Verifythatall holes are properly aligned, and then tighten screws usingaphillipsscrewdriver.
NOTES:
• Alwaysuse multi-washers when attaching
tilt brackets (BB and CC) to your screen.
• Use the corresponding hole in the multi-
washer that matches your screw size as
showninfigure 2.2.
• Spacersmay not beused,depending upon
the type of screen.
MEDIUMHOLEFORM5SCREWS
SMALLHOLEFORM4SCREWS
LARGEHOLEFORM6SCREWS
fig. 2.2 MULTI-
WASHER
SPACER
MULTI-WASHER
SCREW
BB
CC
fig 2.3
fig 2.1 Note: "X"dimensions should be equal.
• Tightenscrews so adapter brackets are firmly
attached. Do not tighten with excessive force.
Overtighteningcan cause stress damage to screws,
greatlyreducing their holding powerand possibly
causingscrew heads to become detached. Tighten to
40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the screen
inserts or if screws bottom out and bracket is still not
tightly secured, damage may occur to screen or
productmay fail.
WARNING
BB
CENTERBRACKETS
VERTICALLYON
BACKOFSCREEN
X
CC
X
KNOBS
FACEOUT

ISSUED: 12-15-02 SHEET #:202-9189-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
6 of 14
With tape measure, measure the outside to outside of the brackets on the back of your screen. If width of the tilt
brackets on back of the screen is over 18-1/2" shown in figure 3.1, using a wrench, attach wing bracket (GG) to
center bracket using two 1/4 serrated flanged locknuts (FF) as shown in figure 3.2. If width of the brackets on back
of the screen is over 30-3/8", using a wrench, attach second wing bracket (GG) to center bracket using two 1/4
serratedflanged locknut (FF)as shown in figure 3.3.
CAUTION: If mounting to two studs on 16" centers, and using the three plate configuration, A STUD
MUST BE SKIPPED in the middle so distance between studs is 32".
AA
18.5"
fig. 3.1
fig. 3.3
FF
AA
GG
fig. 3.2
AA
GG
FF

ISSUED: 12-15-02 SHEET #:202-9189-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
7 of 14
Installation to Double Wood Stud Wall
NOTE: Ifmountingequipmentweighinggreaterthan 200 lbs, triple stud mounting is strongly recommended.
Skip to page 8
Wall plate (AA) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs.
Useof an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each
stud’s center. Place wall plate on wall as a template.The top mounting slots should be 2.5" above the desired
screen center as shown in figure 4.1. Level plate, and mark the center of the four mounting holes. Make sure that the
mounting holes are on the stud centerlines. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that
the wall plate is level, secure it using four #14 x 2.5" wood screws (DD) as shown in figure 4.2.
NOTE: Wall plate may be mounted up to 4" (102 mm) off center as shown in figure 4.1.
Skip to step 5.
• Installermust verify that the supporting surface will safely support the combined loadofthe equipment and all attached
hardwareandcomponents.
• Tightenwood screws so that wall plate is firmly attached,butdo not overtighten. Overtightening can damage the
screws,greatly reducing their holdingpower.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highlyrecommended.
• Hardwareprovided is for attachment of mountthroughstandard thickness drywall or plaster intowoodstuds. Installers
areresponsible to providehardwarefor other typesofmounting situations.
WARNING
fig. 4.1
4"
(102 mm)
CS
4"
(102 mm)
DD AA
fig. 4.2
CS = center of screen
STUD
AA
2.5"
(64 mm)

ISSUED: 12-15-02 SHEET #:202-9189-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
8 of 14
Installation to Triple Wood Stud Wall
fig. 4.3
CS = center of screen
4"
(102 mm) 4" (102 mm)
Wall plate (AA) can be mounted to three studs that are 16" apart. Use a stud finder to locate the edges of the studs.
Useof an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each
stud’s center. Place wall plate on wall as a template.The top mounting slots should be 2.5" above the desired screen
center as shown in figure 4.3. Level plate, and mark the center of the six mounting holes. Make sure that the
mounting holes are on the stud centerlines. Drill six 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the
wall plate is level, secure it using six #14 x 2.5" wood screws (DD) as shown in figure 4.4.
NOTE: Whenmountingequipmentweighinggreater than 200 lbs, triple stud mounting is strongly recommended. If
mounting to two studs on 16" centers, leave an open stud in center. Wall plate may be mounted up to 4" (102 mm)
off-centeras shown in figure 4.3.
Skip to step 5.
• Installermust verify that the supporting surface will safely support the combined loadofthe equipment and all attached
hardwareandcomponents.
• Tightenwood screws so that wall plate is firmly attached,butdo not overtighten. Overtightening can damage the
screws,greatly reducing their holdingpower.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highlyrecommended.
• Hardwareprovided is for attachment of mountthroughstandard thickness drywall or plaster intowoodstuds. Installers
areresponsible to providehardwarefor other typesofmounting situations.
WARNING
2.5"
(64 mm)
CS
DD
AA
fig. 4.4
AA
STUD

ISSUED: 12-15-02 SHEET #:202-9189-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
9 of 14
Installation to Solid Concrete or Cinder Block
Make sure that wall plate (AA) is level, use it as a
templateto mark four mounting holes. The top
mountingholeshould be 2.5" above the desired screen
center as shown in figure 4.1 on page 7. Drill four 1/4"
(6 mm) dia. holes to a minimum depth of 2.5" (64 mm).
Insert anchors (EE) in holes flush with wall as shown
(right).Placewall plate over anchors and secure with
#14 x 2.5" screws (DD). Level, then tighten all
fasteners.
NOTE: Six holes and six sets of fasteners are required
whenmounting the wall plate for equipment weighing
greaterthan200lbs.
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifica-
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to
avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Makesurethat the supporting surface will safely support the combined load of the equipment and all attached hard-
wareand components.
WARNING
CUTAWAY VIEW
INCORRECT
concrete
surface
1
3
2
EE
Drill holes and insert anchors (EE).
CORRECT
Place plate (AA)over anchors (EE) and secure with screws (DD).
Tighten all fasteners.
wall
plate
plaster/
drywall
concrete wall plate concrete
plaster/
drywall
• Always attach concrete anchors directly to load-
bearingconcrete.
• Neverattach concrete anchorsto concrete covered
withplaster, drywall, or other finishing material.If
mountingto concrete surfaces coveredwitha finishing
surfaceis unavoidable, the finishingsurfacemust be
counterbored asshown below. Besure concrete
anchorsdo not pull away from concrete whentighten-
ing screws. If plaster/drywall is thicker than 5/8",
custom fasteners must be supplied by installer.
(NotevaluatedbyUL)
WARNING
AA
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
WARNING
DD
AA
EE
DD
EE
solid concrete cinder block

ISSUED: 12-15-02 SHEET #:202-9189-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
10 of 14
CS
Mounting and Removing Flat Panel Screen
Adjust tension knobs shown in detail 2 to desired
tension, balancing your screen size and weight. The
tension knob, without changing the bracket tension,
can be pulled out, away from the bracket and turned
independentlyof the knob post for readjustment as
shown in Detail 3.
Push or pull from top or bottom of screen to adjust
tilt as shown in figure 6.1. The tilt can be adjusted to
amaximumof 15° forward or 5° backward.
NOTE: To lock the screen into the desired tilt
position, use locator hole to find tilt position hole.
Tighten IncreLok™ tilt locking screws on both tilt
brackets as shown in figure 6.1 and detail 2.
Adjusting the Tilt Angle of the Flat
Panel Screen
• Becareful not to pinch fingers when pushing screen
fromthe bottom.
CAUTION
• Do not tighten screws with excessive force.
Overtighteningcan cause damageto mount. Tighten
screws to 40 in. • lb (4.5 N.M.) maximum torque.
CAUTION
BB and CC
AA
DETAIL 1
AA
• Always use an assistant or mechanical lifting equip-
ment to safely lift and position the plasma television.
WARNING
DETAIL 2
fig 6.1
SAFETY
SCREW
IncreLok™
TILTLOCKING
SCREW
LOCATOR
HOLE
TENSION
KNOB
fig 5.1
fig 5.2
TILTPOSITION
HOLES
4"
CS = center of screen
DETAIL 3
TENSION
KNOB
NOTE: For security, replace safety screw in each tilt
bracket with M5 x 25 security screw (HH) using
wrench(II).
Adjust brackets to full back tilt position and tighten.
Hooktiltbrackets (BBand CC)onto wallplate(AA).
Thenslowly swing screenin as shown. Turnsafety
screws, using wrench (II), clockwise till fully
tightened down and screw tip securely contacts bottom
of the wall plates as shown in detail 1. of figure 5.1.
Centerofscreencanbeadjustedhorizontallynomore
than4"fromcenterofthe wallplateconfiguration, if
desiredasshowninfigure5.2.
NOTE:Tolock the screen down, tighten safety screws
to wall plate using using wrench (II) as shown in detail
1.
Toremove screenfrommount,loosensafetyscrews,
swingscreenaway frommount,and liftscreenoff of
mount.

ISSUED: 12-15-02 SHEET #:202-9189-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
11 of 14
Manufacturer ScreenSize Model ScrewSize ScrewLength washer Spacer Notes
LG 23" 23LX1R M4 12 multi none 2
LG 23" 23LX2R M4 12 multi none 2
LG 23" 23LXRV M4 12 multi none 2
LG 23" L2320A M4 12 multi none 2
LG 23" L2323T M4 12 multi none 2
LG 23" RU-23LZ21 M4 12 multi none 2
LG 23" RU-23LZ50C M4 12 multi none 2
LG 23" Z23L6R M4 12 multi none 2
LG 26" 26LX1D M4 12 multi none 2
LG 26" 26LX2D M4 12 multi none 2
LG 26" L26W56SA M6 16 multi none
LG 26" RM-26LZ30 M4 12 multi none 2
LG 26" RU-26LZ30 M4 12 multi none 2
LG 26" Z26LZ5R M4 12 multi none 2
LG 27" RU-26LZ50 M4 12 multi none 2
LG 27" RU-27LZ50C M4 12 multi none 2
LG 30" DU-30LZ30 M4 12 multi none 2
LG 30" L3000A M5 12 multi none
LG 30" L3000H M4 12 multi none 2
LG 30" L3020T M4 12 multi none 2
LG 30" RL-30LZ50 M4 12 multi none 2
LG 30" RZ-30LZ50 M4 12 multi none 2
LG 30" RU-30LZ50C M4 12 multi none 2
LG 32" 32LC2D M4 12 multi none 2
LG 32" L3200A M6 12 none none 3
LG 32" L3200AK M6 12 none none 3
LG 32" L3200T M4 8 multi none 1
LG 32" L3200TC M4 8 multi none 1
LG 32" L3200TK M4 8 multi none 1
LG 32" RU-32LZ30C M4 12 multi none 2
LG 32" RU-32LZ50C M4 12 multi none 2
LG 32" L3200A M6 12 multi none 3
LG 32" L3200AK M6 12 multi none 3
LG 37" 37LB1DA M8 25 none 8.7mm ID
LG 37" 37LP1D M5 12 multi none
LG 37" DU-37LZ30 M5 25 multi 5.6mm ID
LG 37" DU-37LZ30C M5 25 multi 5.6mm ID
LG 37" L3700A M5 12 multi none
LG 37" L3700AK M5 12 multi none
LG 37" L3700T M5 12 multi none
LG 37" L3700TC M5 12 multi none
LG 37" L3700TK M5 12 multi none
LG 37" M3700C-BA M5 12 multi none
LG 37" M3701C M5 12 multi none
LG 37" 37LB1DA M5 12 multi none
LG 40" MU-40PA10B M5 25 multi 5.6mm ID
LG 42" 42LB1DR M5 12 multi none
LG 42" 42LB1DRA M5 12 multi none
LG 42" 42LC2D M5 12 multi none
LG 42" 42PC1DA M5 12 multi none
LG 42" 42PC3D M5 12 multi none
LG 42" 42PC3DV M5 12 multi none
LG 42" 42LP1DC M5 12 multi none
LG 42" 42PM1M M5 12 multi none
LG 42" 42PX10 M5 25 multi 5.6mm ID
LG 42" 42PX20 M5 25 multi 5.6mm ID
LG 42" 42PX3DBV M5 40 multi 28.6mm tall 4
LG 42" 42PX3DLV M5 40 multi 28.6mm tall 4
LG 42" 42PX3DCV M5 25 multi 5.6mm ID
LG 42" 42PX4D M5 25 multi 5.6mm ID
LG 42" 42PX5D M5 25 multi 5.6mm ID
LG 42" 42PX7DC M5 12 multi none
LG 42" DU-42LZ30 M5 25 multi 5.6mm ID
LG 42" DU-42PX10C M5 25 multi 5.6mm ID
LG 42" DU-42PX11 M5 25 multi 5.6mm ID
LG 42" DU-42PX12X M5 25 multi 5.6mm ID
LG 42" DU-42PX12XC M5 25 multi 5.6mm ID
LG 42" DU-42PX12XD M5 25 / 40 multi 5.6mm ID 5
LG 42" DU-42PY10 M5 25 multi 5.6mm ID
See chart below to determine the fasteners to use with your screen. If your screen has a note in the far right column, then reference it on the last page.
PWMT300

ISSUED: 12-15-02 SHEET #:202-9189-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
12 of 14
Manufacturer ScreenSize Model ScrewSize ScrewLength washer Spacer Notes
See chart below to determine the fasteners to use with your screen. If your screen has a note in the far right column, then reference it on the last page.
PWMT300
LG 42" DU-42PZ60 M5 25 multi 5.6mm ID
LG 42" MP-42PZH12 M5 25 multi 5.6mm ID
LG 42" MU-42PM10/11 M5 25 multi 5.6mm ID
LG 42" MU-42PM12X M5 25 multi 5.6mm ID
LG 42" MU-42PZ15B M5 25 multi 5.6mm ID
LG 42" MU-42PZ41V M5 25 multi 5.6mm ID
LG 42" MU-42PZ44V M5 25 multi 5.6mm ID
LG 42" MU-42PZ90C M5 25 multi 5.6mm ID
LG 42" MU-42PZ90H M5 25 multi 5.6mm ID
LG 42" MU-42PZ90M M5 25 multi 5.6mm ID
LG 42" MU-42PZ90V M5 25 multi 5.6mm ID
LG 42" MU-42PZ90XC M5 25 multi 5.6mm ID
LG 42" MU-42PZ94V M5 25 multi 5.6mm ID
LG 42" RU-42PX10C M5 25 multi 5.6mm ID
LG 42" RU-42PX11 M5 25 multi 5.6mm ID
LG 42" RU-42PZ61 M5 25 multi 5.6mm ID
LG 42" RU-42PZ71 M5 25 multi 5.6mm ID
LG 42" RU-42PZ90 M5 25 multi 5.6mm ID
LG 42" RU-42PZ90V M5 25 multi 5.6mm ID
LG 42" 42LB1DR M5 12 multi none
LG 42" 42LB1DRA M5 12 multi none
LG 42" 42LC2D M5 12 multi none
LG 42" 42PC1DA M5 12 multi none
LG 42" 42PC3D M5 12 multi none
LG 42" 42PC3DV M5 12 multi none
LG 42" 42LP1DC M5 12 multi none
LG 42" 42PM1M M5 12 multi none
LG 42" 42PX10 M5 25 multi 5.6mm ID
LG 42" 42PX20 M5 25 multi 5.6mm ID
LG 42" 42PX3DBV M5 40 multi 28.6mm tall 4
LG 42" 42PX3DLV M5 40 multi 28.6mm tall 4
LG 42" 42PX3DCV M5 25 multi 5.6mm ID
LG 42" 42PX4D M5 25 multi 5.6mm ID
LG 42" 42PX5D M5 25 multi 5.6mm ID
LG 42" 42PX7DC M5 40 multi 28.6mm tall 4
LG 42" DU-42LZ30 M5 25 multi 5.6mm ID
LG 42" DU-42PX10C M5 25 multi 5.6mm ID
LG 42" DU-42PX11 M5 25 multi 5.6mm ID
LG 42" DU-42PX12X M5 25 multi 5.6mm ID
LG 42" DU-42PX12XC M5 25 multi 5.6mm ID
LG 42" DU-42PX12XD M5 25 multi 5.6mm ID
LG 42" DU-42PY10 M5 25 multi 5.6mm ID
LG 42" DU-42PZ60 M5 25 multi 5.6mm ID
LG 42" L4200A M5 12 multi none
LG 42" L4200AF M5 12 multi none
LG 42" L4200AT M5 12 multi none
LG 42" M4200C-BA M5 12 multi none
LG 42" M4200N M5 12 multi none
LG 42" MP-42PZH12 M5 25 multi 5.6mm ID
LG 42" MU-42PM10/11 M5 25 multi 5.6mm ID
LG 42" MU-42PM12X M5 25 multi 5.6mm ID
LG 42" MU-42PZ15B M5 25 multi 5.6mm ID
LG 42" MU-42PZ41V M5 25 multi 5.6mm ID
LG 42" MU-42PZ44V M5 25 multi 5.6mm ID
LG 42" MU-42PZ90C M5 25 multi 5.6mm ID
LG 42" MU-42PZ90H M5 25 multi 5.6mm ID
LG 42" MU-42PZ90M M5 25 multi 5.6mm ID
LG 42" MU-42PZ90V M5 25 multi 5.6mm ID
LG 42" MU-42PZ90XC M5 25 multi 5.6mm ID
LG 42" MU-42PZ94V M5 25 multi 5.6mm ID
LG 42" RU-42PX10C M5 25 multi 5.6mm ID
LG 42" RU-42PX11 M5 25 multi 5.6mm ID
LG 42" RU-42PZ61 M5 25 multi 5.6mm ID
LG 42" RU-42PZ71 M5 25 multi 5.6mm ID
LG 42" RU-42PZ90 M5 25 multi 5.6mm ID
LG 42" RU-42PZ90V M5 25 multi 5.6mm ID
LG 47" 47LB1 M5 12 multi none
LG 47" 47LB1 M5 12 multi none
LG 50" 50PC1DR M5 12 multi none

ISSUED: 12-15-02 SHEET #:202-9189-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
13 of 14
Manufacturer ScreenSize Model ScrewSize ScrewLength washer Spacer Notes
See chart below to determine the fasteners to use with your screen. If your screen has a note in the far right column, then reference it on the last page.
PWMT300
LG 50" 50PC1DRA M5 12 multi none
LG 50" 50PC3D M5 12 multi none
LG 50" 50PM1M M5 25 multi 5.6mm ID
LG 50" 50PX1D M5 25 multi 5.6mm ID
LG 50" 50PX10 M5 25 multi 5.6mm ID
LG 50" 50PX20 M5 25 multi 5.6mm ID
LG 50" 50PX4DR-H M5 25 multi 5.6mm ID
LG 50" 50PX5D M5 25 multi 5.6mm ID
LG 50" 50PY20 M5 25 multi 5.6mm ID
LG 50" DU-50PM10C M5 25 multi 5.6mm ID
LG 50" DU-50PX10C M5 25 multi 5.6mm ID
LG 50" DU-50PY10 M5 25 multi 5.6mm ID
LG 50" DU-50PZ60 M5 25 multi 5.6mm ID
LG 50" DU-50PZ60H M5 25 multi 5.6mm ID
LG 50" MU-50PM10/11 M5 25 multi 5.6mm ID
LG 50" MU-50PZ41 M5 25 multi 5.6mm ID
LG 50" MU-50PZ41B M5 25 multi 5.6mm ID
LG 50" MU-50PZ41V M5 25 multi 5.6mm ID
LG 50" MU-50PZ90C M5 25 multi 5.6mm ID
LG 50" MU-50PZ90V M5 25 multi 5.6mm ID
LG 50" RU-50PZ61 M5 25 multi 5.6mm ID
LG 50" 50PC1DR M5 12 multi none
LG 50" 50PC1DRA M5 12 multi none
LG 50" 50PC3D M5 12 multi none
LG 50" 50PM1M M5 25 multi 5.6mm ID
LG 50" 50PX1D M5 25 multi 5.6mm ID
LG 50" 50PX10 M5 25 multi 5.6mm ID
LG 50" 50PX20 M5 25 multi 5.6mm ID
LG 50" 50PX4DR-H M5 25 multi 5.6mm ID
LG 50" 50PX5D M5 25 multi 5.6mm ID
LG 50" 50PY20 M5 25 multi 5.6mm ID
LG 50" DU-50PM10C M5 25 multi 5.6mm ID
LG 50" DU-50PX10C M5 25 multi 5.6mm ID
LG 50" DU-50PY10 M5 25 multi 5.6mm ID
LG 50" DU-50PZ60 M5 25 multi 5.6mm ID
LG 50" DU-50PZ60H M5 25 multi 5.6mm ID
LG 50" MU-50PM10/11 M5 25 multi 5.6mm ID
LG 50" MU-50PZ41 M5 25 multi 5.6mm ID
LG 50" MU-50PZ41B M5 25 multi 5.6mm ID
LG 50" MU-50PZ41V M5 25 multi 5.6mm ID
LG 50" MU-50PZ90C M5 25 multi 5.6mm ID
LG 50" MU-50PZ90V M5 25 multi 5.6mm ID
LG 50" RU-50PZ61 M5 25 multi 5.6mm ID
LG 55" 55LP1M M5 12 multi none
LG 55" M5500C-BA M5 12 multi none
LG 60" DU-60PY10 M8 16 none none
LG 60" DU-60PZ60 M8 16 none none
LG 60" MU-60PZ10 M8 16 none none
LG 60" MU-60PZ12 M8 16 none none
LG 60" MU-60PZ90C M8 16 none none
LG 60" MU-60PZ90V M8 16 none none
LG 60" MU-60PZ95V M8 16 none none
LG 60" DU-60PY10 M8 16 none none
LG 60" DU-60PZ60 M8 16 none none
LG 60" MU-60PZ10 M8 16 none none
LG 60" MU-60PZ12 M8 16 none none
LG 60" MU-60PZ90C M8 16 none none
LG 60" MU-60PZ90V M8 16 none none
LG 60" MU-60PZ95V M8 16 none none
LG 71" MW-71PY10 M8 16 none none

ISSUED: 12-15-02 SHEET #:202-9189-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
14 of 14
1 All hardware may not be included. If you are missing the additional fasteners needed for your screen, then please
contact Customer Care at 1-800-865-2112.
2 If back of screen has a bumpout, or if mounting holes lie in pockets, then use M4 X25 mm screw with 12.7mm tall
spacers
3If screw gets less than 3 threads of engagement, then try the next longer length screw. If all longer lengths have
been tried, and there is still less than 3 threads of engagement, then contact Customer Care for assistance.
4 If back of screen has a bumpout, remove it, or use the 15.9mm tall spacer and stack that with the 12.7mm spacer
to give you the 28.6mm spacing.
5 For top mounting holes use M5 x 25 mm screws with 5.6mm ID spacers, for bottom mounting holes use M5 x
40mm screws with 5.6mm ID spacers in both cases.
NOTES (only pertains to the screen specified in the configuration chart)
* The mount includes 12.7mm tall spacers
©2006PeerlessIndustries,Inc. Allrightsreserved.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.