LG LTNC11131V User manual

INSTALLATION
Installation Overview
Please read the following installation instructions first after purchasing this product or transporting it
to another location.
1 Unpacking your
refrigerator
2 Choosing the proper
location
This appliance is intended to be used in household and similar applications such as:
-Staff kitchen areas in shops, offices and other working environments; farm houses and by clients in
hotels, motels and others residential type environments.
-Bed and breakfast type environments; catering and similar non-retail applications.
Specifications
The appearance and specifications listed in this manual may vary due to constant product
improvements.
Dimensions
LTNC08121V
56,2 kg (124 lb.)
Width
24 in
(610 mm)
Net Weight
Depth
26 in
(661 mm)
Heigth
66 1/2 in
(1690 mm)
Dimensions
49kg (108.03 lb.)
Width
21.9 in
(555 mm)
Net Weight
Depth
24.6 in
(625 mm)
Heigth
61.6 in
(1565 mm)
8INSTALLATION
3 Leveling and Door
Alignment
ENGLISH
LTNC11131V

Unpacking Your Refrigerator
Choosing the Proper Location
Flooring
NOTE
WARNING
To reduce the risk of electric shock, do not
install the refrigerator in a wet or damp area.
WARNING



back or other injury.
Use two or more people to move and install
the refrigerator. Failure to do so can result in
Your refrigerator is heavy. When moving the
refrigerator for cleaning or service, be sure to
protect the floor. Always pull the refrigerator
straight out when moving it. Do not wiggle or
walk the refrigerator when trying to move it,
Keep flammable materials and vapors, such
as gasoline, away from the refrigerator.
Failure to do so can result in fire, explosion,
as floor damage could occur.
or death.
Remove tape and any temporary labels from your
refrigerator before using. Do not remove any
warning-type labels, the model and serial number
To remove any remaining tape or glue, rub the
area briskly with your thumb. Tape or glue residue
can also be easily removed by rubbing a small
amount of liquid dish soap over the adhesive with
your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol,
flammable fluids, or abrasive cleaners to remove
tape or glue. These products can damage the
Refrigerator shelves are installed in the shipping
position. Please reinstall shelves according to your
labels.
individual storage needs.
surface of your refrigerator.
The refrigerator should always be plugged
into its own individual properly grounded
electrical outlet rated for 115V
~ 60 Hz, AC only,
This provides the best performance and also
prevents overloading house wiring circuits
which could cause a fire hazard from
overheated wires. It is recommended that a
separate circuit serving only this appliance be
Installing on carpeting, soft tile surfaces, a
platform or weakly supported structure is
provided.
and fused at 15 A.


To avoid noise and vibration, the unit must be
leveled and installed on a solidly constructed
floor. If required, adjust the leveling legs to
compensate for unevenness of the floor. The
front should be slightly higher than the rear to
aid in door closing. Leveling legs can be turned
easily by tipping the cabinet slightly. Turn the
leveling legs to the left to raise the unit or to
the right to lower it (See Leveling section).
not recommended.
Ambient Temperature
Install this appliance in an area where the
temperature is between 55°F (13°C) and
110°F (43°C). If the temperature around the
appliance is too low or high, cooling ability
may be adversely affected.
9
INSTALLATION
ENGLISH

Measuring the Clearances
Turning On The Power
Plug in the refrigerator.
CAUTION
1
Leveling
Screwdriver
Leveling
Screw



1.
NOTE
2.
Too small of a distance from adjacent
items may result in lowered freezing capability
and increased electricity consumption charges.
Allow at least 24 inches (61 cm) in front of
the refrigerator to open the doors, and at
least 2 inches (5.08 cm) between the refrig-
erator and the wall.
Connect to a rated power outlet.
Have a certified electrician check the wall
outlet and wiring for proper grounding.
Do not damage or cut off the ground
terminal of the power plug.
After installing, plug the refrigerator’s power
cord into a 3-prong grounded outlet and push
the refrigerator into the final position.
Your refrigerator has two front leveling legs (one
on the right side and one on the left). Adjust the
legs to alter the tilt from front-to-front or side-to
-side. If the refrigerator seems unsteady, or you
want the doors to close more easily, adjust the
refrigerator’s tilt using the instructions below:
Turn the leveling legs by inserting a flat blade
screwdriver in the holes located in the leveling
screws. Turn the leg clockwise ( ) to raise
that side of the refrigerator or counterclock-
wise ( )to lower it. It may take several turns
of the leveling leg to adjust the tilt of the
refrigerator.
Having someone push backward against the
top of the refrigerator takes some weight off
the leveling legs. This makes it easier to adjust
the legs.
Open both doors again and check to make
sure that they close easily. If the doors do not
close easily, tilt the refrigerator slightly more to
the rear by turning both leveling legs counter-
clockwise. It may take several more turns, and
you should turn both leveling legs the same
amount.
10 INSTALLATION
ENGLISH
2” (5.08 cm)
2” (5.08 cm)
2” (5.08 cm) 2” (5.08 cm)