FCC Compliance Statement
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment and the
receiver.
yConnect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
yConsult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modications in construction of this device
which are not expressly approved by the party responsible
for compliance could void the user’s authority to operate
the equipment.
FCC RF Radiation Exposure Statement : This equipment
complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not
be co-located or operating in conjunction with any other
antenna or transmitter.
This equipment should be installed and operated with
minimum distance 20 cm (7.8 inches) between the
antenna and your body. Users must follow the specic
operating instructions for satisfying RF exposure
compliance.
FCC Radio Frequency Interference Requirements :
High power radars are allocated as primary users of the
5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These
radar stations can cause interference with and/or damage
this device. This device cannot be co-located with any other
transmitter.
Responsible Party :
LG Electronics USA, Inc.
1000 Sylvan Ave
Englewood Cliffs, NJ 07632
Tel: 1-800-243-0000
aConnect the power cord of the wireless receiver
to the AC outlet.
bTurn on the unit: The unit and wireless receiver
will be automatically connected. The receiver's
yellow - green LED turns on
Wireless Receiver Connection Manually
If the rear speakers do not make sound, try to
connect manually.
aPress PAIRING button on the rear of the
wireless receiver.
yThe yellow - green LED on the wireless receiver
blinks quickly.
bTurn on the main unit.
cPairing is completed.
yThe yellow - green LED on the wireless receiver
turns on.
Rear Speakers Connection1
Wireless Receiver Connection2
aConnect the speaker cables to rear speakers
correctly.
bConnect the Wireless Receiver and the rear
speakers (Grey: right, Blue: left) with the speakers
cables.
cTurn on the Surround function to enjoy surround
sound.
Speaker design and connection method may be
different according to models.
Rear speaker
(Left)
Wireless
Receiver Rear speaker
(Right)
Transparent
Black stripe
Transparent
Black stripe
Surround Sound On/Off
When you turn on surround function, you can enjoy
magnificent surround sound for all the input sound
source with rear speakers.
The initial setting for the surround function is
OFF, turn the surround function ON to use it.
SK5Y
Surround On: Press and hold REAR obutton on the
remote control about 2 seconds.
Surround Off: Press and hold REAR pbutton on the
remote control about 2 seconds.
SK10Y/SK9Y/SK8Y/SK6Y
Surround On: Press and hold AUTO VOL button on the
remote control about 2 seconds and then press AUTO
VOL button repeateadly to select ON - SURROUND in
the display window.
Surround Off: Press and hold AUTO VOL button on the
remote control about 2 seconds and then press AUTO
VOL button repeateadly to select OFF - SURROUND in
the display window.
Additional Information
Specication of Wireless receiver
Power
requirement
Refer to the main label on the
wireless receiver.
Power
consumption
Refer to the main label on the
wireless receiver.
Dimensions
(W x H x D)
Approx.
60.0 mm x 220.0 mm x
175.0 mm
(2.4 inch x 8.7 inch x
6.9 inch)
Design and specications are subject to change
without notice.
About Ferrite Core (Optional)
twice
SPK8-S.DUSALLK_SIM_MFL70547243.indd 3-4 2018-06-11 1:14:22
