LG F1222TD User manual

Washing Machine
OWNER'S MANUAL
F1422TD(1~9)
F1222TD(1~9)
F1022TD(1~9)
Thank you for buying a
LG Fully Au oma ic Washing machine.
Please read your owner's manual carefully, i provides
ins ruc ions on safe ins alla ion, use and main enance.
Re ain i for fu ure reference.
Record he model and serial numbers of your washing machine.

2
roduct Features
P
ontents
C
Warnings....................................................................................3
Specifica ions.............................................................................4
Ins alla ion..................................................................................5
Care before washing................................................................11
Adding de ergen .....................................................................12
Func ion ...................................................................................14
How o use washer ..................................................................15
Main enance ............................................................................22
Troubleshoo ing guide .............................................................26
Terms of Warran y ...................................................................29
추가선택, 예약,
Protection against creases
Wi h he al erna e ro a ion of he drum, creasing in he laundry is
minimized.
Built-in Heater
In ernal hea er au oma ically hea s he wa er o he bes
empera ure on selec ed cycles.
More economical by Intelligent Wash System
In elligen Wash Sys em de ec s he amoun of load and wa er
empera ure, and hen de ermines he op imum wa er level and
washing ime o minimize energy and wa er consump ion.
Child Lock
The Child lock preven s children from pressing any bu on o
change he se ings during opera ion.
Low noise speed control system
By sensing he amoun of load and balance, i evenly dis ribu es
load o minimize he spinning noise level.
Direct Drive System
The advanced Brushless DC mo or direc ly drives he drum wi hou
bel and pulley.

3
arnings
W
For your safety, the information in this manual must be follo ed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.
!
READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE
WARNING!
❊ Do not push do n the door excessively, hen asher door open.
This could topple over the asher.
• Before ins alla ion, check ex erior damages. If i has,
do no ins all.
• Do no ins all or s ore he washer where i will
be exposed o he wea her.
• Do no amper wi h con rols.
• Do no repair or replace any par of he washer
or a emp any servicing unless specifically
recommended in he user-main enance ins ruc ions
or published user-repair ins ruc ions ha you
unders and and have he skills o carry ou .
• Keep he area undernea h and around your
appliances free of combus ible ma erials such as
lin , paper, rags, chemicals, e c.
• Close supervision is necessary if his appliance is
used by or near children. Do no allow children o
play on, wi h, or inside his or any o her appliance.
• Keep small animals away from he appliance.
• Do no leave he washer door open.
An open door could en ice children o hang on he
door or crawl inside he washer.
• Never reach in o washer while i is moving. Wai
un il he drum has comple ely s opped.
• The laundry process can reduce he flame re ardan
of fabrics.
• To avoid such a resul , carefully follow he garmen
manufac urer’s wash and care ins ruc ions.
• Do no wash or dry ar icles ha have been cleaned
in, washed in, soaked in, or spo ed wi h
combus ible or explosive subs ances (such as wax,
oil, pain , gasoline, degreasers, dry-cleaning
solven s, kerosene, e c.) which may igni e or
explode. Oil may remain in he ub af er a whole
cycle resul ing in fire during drying. So, do no load
oiled clo hes.
• Do no slam he washer door closed or ry o force
he door open when locked. This could resul in
damage o he washer.
• When he machine runs high empera ure, he fron
door may be very ho . Don’ ouch i .
• To minimize he possibili y of elec ric shock, unplug
his appliance from he power supply or disconnec
he washer a he household dis ribu ion panel by
removing he fuse or swi ching off he circui breaker
before a emp ing any main enance or cleaning.
• When unplugging power cord, do no pull ou by
grasping he cord. O herwise, he power cord may
be damaged.
• Never a emp o opera e his appliance if i is
damaged, malfunc ioning, par ially disassembled, or
has missing or broken par s, including a damaged
cord or plug.
• Before discarding an old machine unplug i . Render
he plug useless. Cu off he cable direc ly behind
he appliance o preven misuse.
• When a produc was under wa er, Please call
service cen er. The risk of elec ric shock and fire.
GROUNDING INSTRUCTIONS
This appliance mus be grounded. In he even of malfunc ion or breakdown, grounding will reduce he risk of elec ric shock by providing a pa h
of leas resis ance for elec ric curren . This appliance is equipped wi h a cord having an equipmen -grounding conduc or and grounding plug.
The plug mus be plugged in o an appropria e ou le ha is properly ins alled and grounded in accordance wi h all local codes and ordinance.
• Do no use an adap er or o herwise defea he grounding plug.
• If you don’ have he proper ou le , consul an elec rician.
IMPORTANT SAFETY INSTRUCTIONS
WARNING :To reduce he risk of fire, elec ric shock, or injury o persons when using
he washer, follow basic precau ions, including he following:
SAVE THESE INSTRUCTIONS
WARNING : Improper connec ion of he equipmen -grounding conduc or can resul in risk of elec ric shock. Check wi h
a qualified elec rician or serviceman if you are in doub as o whe her he appliance is properly grounded. Do no modify
he plug provided wi h he appliance - if i does no fi he ou le , have a proper ou le ins alled by a qualified elec rician.

4
pecifications
S
Spanner
Inle hose(1EA)
■ Accessories
■Name : Fron loading washing machine
■Power supply : 220-240V~,50Hz
■Size : 600mm(W) 550mm(D) 850mm(H)
■Weigh /Max.Wa : 58kg / 2100W
■Wash capaci y : 8kg
■Wa er consump ion : 56ℓ(7ℓ/ kg)
■Permissible wa er pressure : 0.3-10kgf/㎠(30-1000kPa)
■Spin speed :
No Spin/400/800/1400 [F1422TD(1~9)]
No Spin/400/800/1200 [F1222TD(1~9)]
No Spin/400/800/1000 [F1022TD(1~9)]
󳢮The appearance and specifica ions may be varied wi hou no ice o raise he uni s quali y.

5
nstallation
I
1. To preven in ernal damage during
ranspor , he special 4 bol s are
locked. Before opera ing he washer,
remove
he bol s along wi h he rubber bungs.
• If hey are no removed, i may cause
heavy vibra ion, noise and malfunc ion.
3. Take ou he 4 bol s along wi h he
rubber bungs by sligh ly wis ing he
bung. Keep he 4 bol s and he
spanner for fu ure use.
• Whenever he appliance is ranspor ed,
he ransi bol s mus be refi ed.
The appliance is fi ed wi h ransi bol s o preven in ernal damage during ranspor .
• Packing and all transit bolts must
be removed before using the
washer.
󳢹When unpacking the base, be
sure to remove the additional
packing support in the middle
of the base packing.
2. Unscrew he 4 bol s wi h
he spanner supplied.
4. Close he holes wi h he caps supplied.
 Transit bolts
Install or store where it will not be ex osed to tem eratures below freezing or ex osed to the weather.
Pro erly ground washer to conform with all governing codes and ordinances.
The base o ening must not be obstructed by car eting when the washing machine is installed on a
car eted floor.
In countries where there are areas which may be subject to infestation by cockroaches or other vermin,
ay articular attention to kee ing the a liance and its surroundings in clean condition at all times.
Any damage which may be cause by cockroaches or other vermin will not be covered by the a liance
guarantee.
 Removing transit bolts
Base Packing
Washer
Packing Suppor
(Packing suppor may no
be used depending on
models.)

6
nstallation
I
Laundry
Tub
Washer
approx.
2cm
Drain Hose
 Installation place requirement
 BS Plug Safety Details (For U.K. User)
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
GREEN AND YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
This appliance mus be ear hed
As he colours of he wires in he mains lead of his appara us may no correspond wi h he coloured markings iden ifying
he erminals in your plug, proceed as follows:
The wire which is coloured Green and Yellow mus be connec ed o he erminal in he plug which is marked wi h he le er E
or by he ear h symbol or coloured Green or Green and Yellow.
The wire which is coloured Blue mus be connec ed o he erminal which is marked wi h he le er N or coloured Black.
The wire which is coloured Brown mus be connec ed o he erminal which is marked wi h he le er L or coloured Red.
If a 13 amp (BS 1363) plug is used, fi a 13 amp BS 1362 fuse.
Green and Yello (Earth)
Bro n(Live)
Blue(Neutral)
Cord
grip
Fuse
E
L
N
 Positioning
Ins all he washer on a fla hard floor.
Make sure ha air circula ion around he washer is no impeded by carpe s,rug e c.
• Never ry o correc any unevenness in he floor wi h pieces of wood, cardboard or similar
ma erials under he washer.
• If i is impossible o avoid posi ioning he washer nex o a gas cooker or coal burning
s ove,an insula ing(85x60cm) covered wi h aluminum foil on he side facing he cooker or
s ove,mus be inser ed be ween he wo appliance.
• The washer mus no be ins alled in rooms where he empera ure can drop below 0°C.
• Please ensure ha when he washer is ins alled, i is easily accessible for he engineer in
he even of a breakdown.
• Wi h he washer ins alled adjus all four fee using he ransi bol spanner provided
ensuring he appliance is s able, and a clearance of approxima ely 20mm is lef be ween
he op of he washer and he underside of he work- op.
Level floor :
Allowable slope under en ire washer is 1˚
Po er outlet :
Mus be wi hin 1.5 me ers of ei her side of loca ion of
washer. Do no overload he ou le wi h more han one
appliance.
Additional Clearance :
For wall, door and floor modeling is required.
(10cm : rear /2cm:righ & lef side)
Do no place or s ore laundry produc s on op of washer a
any imes.
They can damage he finish or con rols.

7
nstallation
I
▶Water supply pressure must be between 30kPa and 1000kPa
(0.3~10kgf/cm2)
▶D n’t strip r cr ssthread when c nnecting Inlet h se t the valve.
▶If the water supply pressure is m re than 1000kPa, a dec mpressi n device
sh uld be installed.
• Two rubber seals are supplied wi h he wa er inle hoses. They are
used for preven ing wa er leaks.
• Make sure he connec ion o aps is igh enough.
• Periodically check he condi ion of he hose and replace he hose if
necessary.
• Make sure ha here is no kink on he hose and ha i is no crushed.
■ Washing Machine is to be connected to the water mains using new hose-sets and old hose-sets should
not be used.
■ Connecting water supply hose
1. Do no use an ex ension cord or double adap er.
2. If he supply cord is damaged, i mus be replaced by he manufac urer or i s service agen s or similarly
qualified person in order o avoid a hazard.
3. Always unplug he machine and urn off he wa er supply af er use.
4. Connec he machine o an ear hed socke in accordance wi h curren wiring regula ions.
5. The appliance mus be posi ioned so ha he plug is easily accessible.
• Repairs o he washing machine mus only be carried ou by qualified personnel. Repairs carried ou by
inexperienced persons may cause injury or serious malfunc ioning. Con ac your local service cen er
• Do no ins all your washing machine in rooms where empera ure below freezing may occur. Frozen hoses may burs
under pressure. The reliabili y of he elec ronic con rol uni may be impaired a empera ures below freezing poin .
• If he appliance is delivered in he win er mon hs and empera ures are below freezing : Place he washing
machine a room empera ure for a few hours before pu ing i in o opera ion.
■ Electrical connection
CAUTION concerning the Po er Cord
Mos appliances recommend hey be placed upon a dedica ed circui ; ha is, a single ou le circui
which powers only ha appliance and has no addi ional ou le s or branch circui s. Check he
specifica ion page of his owner's manual o be cer ain.
Do no overload wall ou le s. Overloaded wall ou le s, loose or damaged wall ou le s, ex ension cords,
frayed power cords, or damaged or cracked wire insula ion are dangerous. Any of hese condi ions
could resul in elec ric shock or fire. Periodically examine he cord of your appliance, and if i s
appearance indica es damage or de eriora ion, unplug i , discon inue use of he appliance, and have
he cord replaced wi h an exac replacemen par by an au horized servicer.
Pro ec he power cord from physical or mechanical abuse, such as being wis ed, kinked, pinched,
closed in a door, or walked upon. Pay par icular a en ion o plugs, wall ou le s, and he poin where
he cord exi s he appliance.
CAUTION
NOTE
After completing connection, if water leaks from the hose, repeat the same steps. Use the most conventional type
of faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the
faucet into the adaptor.

8
nstallation
I
 Normal Tap without thread & screw type inlet hose
 Normal Tap without thread & one touch type inlet hose (Single inlet models)
1.Unscrew he fixing screw o
a ach he ap.
2.Push he connec or up ill he
rubber packing is in igh con ac
wi h he ap. Then igh en he 4
screws.
3.Push he wa er supply hose
ver ically upwards so ha he
rubber packing wi hin in he
hose can adhere comple ely o
he ap and hen igh en i by
screwing i o he righ .
1.Un igh en he upper connec or
screw.
2.Push he upper connec or up ill
he rubber packing is in igh
con ac wi h he ap. Then
igh en he 4 screws.
3. Connec he wa er supply hose
o he middle connec or,
pushing he pla e down.
• Make sure ha here are no
kinks in he hose and ha i is
no crushed.
• Make sure ha he rubber seal
is inside he hose connec or.
Upper
Connec or Rubber
packing
Middle
connec or
Fixing screw
Guide pla e
Connec or
Rubber seal
Hose connec or
Used the horizontal tap
Horizon al ap
Ex ension ap
Square ap
Rubber packing
Upper
Connec or
Middle
connec or
Pla e
Upper
Connec or
Wa er supply
hose
• In case he diame er of he ap is
large remove he guide pla e.
• Turn he middle connec or no
o have wa er leaked.
• To separa e he wa er supply
hose from he middle connec or
shu off he ap. Then pull he
inle hose down, pushing he
pla e down.

9
nstallation
I
 Installation of drain hose
• The drain hose should no be placed
higher han 100 cm above he floor.
• Proper securing of he drain hose will
pro ec he floor from damage due o
wa er leakage.
• When he drain hose is oo long, do
no force back in o he washer. This
will cause abnormal noise.
• When ins alling he drain hose sink,
secure i igh ly wi h a s ring.
• Proper securing of he drain hose will
pro ec he floor from damage due o
wa er leakage.
This equipmen is no designed for mari ime use or for use mobile ins alla ions such as
caravans, aircraf e c.
Turn off he s opcock if he machine is o be lef for any leng h of ime (e.g. holiday),
especially if here is no floor drain(gully) in he immedia e vicini y.
When disposing of he appliance, cu off he mains cable, and des roy he plug Disable he
door lock o preven young children being rapped inside.
Packaging ma erial (e.g. Films, S yrofoam) can be dangerous for children. There is a risk
of suffoca ion !
Keep all packaging well away from children

10
nstallation
I
 Level adjustment

Concrete floors

Wooden floors (Suspended floors)
1. Adjus ing he washing machine level properly preven s excessive
noise and vibra ion.
Ins all he appliance on a solid and level floor surface, preferably in a
corner of he room.
2. If he floor is uneven, adjus he adjus able fee as required. (do no
inser pieces of wood e c. under he fee )
Make sure ha all four fee are s able and res ing on he floor and
hen check ha he appliance is perfec ly level. (use a spiri level)
※※
After the washer is level, tighten the lock nuts up towards of the base of
the washer. All lock nuts must be tightened.
❊ Diagonal Check
When pushing down the edges of the washing machine top plate diagonally, the machine
should not move up and down at all. (Please, check both of two directions
If machine rocks when pushing the machine top plate diagonally, adjust the feet again.
• The installation surface must be clean, dry and level.
• Install washer on a flat hard floor.

Tile floors (Slippery floors)
• Position each foot on the Tread Mate and level the machine to suit. (Cut Tread Mate into 70x70 mm
sections and stick the pieces on to the dry tile where machine is to be placed.)
※※
Tread Mate is a self adhesive material used on ladders & steps that prevents slipping.
• Wooden floors are particularly susceptible to vibration.
• To prevent vibration we recommend you place rubber cups under each foot,
at least 15mm thick under the washer, secured to at least 2 floor beams with screws.
• If possible install the washer in one of the corners of the room, where the floor is more stable.
※※
Insert the rubber cups to reduce vibration.
※※
You can obtain the rubber cups (p/no.4620ER4002B from the LG spares dept.
Important!
• Proper placement and levelling of the washer ensure long,regular and reliable operation.
• The washer must be absolutely horizontal and stand firmly in position.
• It must not “Seesaw” across corners under load.
• The installation surface must be clean, free from floor wax and other lubricant coatings.
• Do not let the feet of the washer get wet. If feet of the washer get wet, slipping may occur.
Rubber Cup
NOTE
Timber or suspended type flooring may contribute to
excessive vibration and unblance errors.
NOTE
In the case that the washing machine is installed on a raised
platform, it must be securely fastened in order
to eliminate the risk that it might fall off.

11
are before washing
C
1. Care Labels
Look for a care label on your clo hes. This will ell you abou he fabric con en of your garmen and
how i should be washed.
2. Sorting
To ge he bes resul s, Sor clo hes in o loads ha can be washed wi h he same wash cycle.
Wa er empera ure and spin speed and differen fabrics need o be washed in differen ways.
Always sor dark colors from pale colors and whi es. Wash separa ely as dye and lin ransfer can
occur causing discolora ion of whi e e c. If possible, do no wash heavily soiled i ems wi h ligh ly
soiled one.
Soil (Heavy, Normal, Ligh ) Separa e clo hes according o amoun of soil.
Color (Whi e, Ligh s, Darks) Separa e whi e fabrics from colored fabrics.
Lin (Lin producers, Collec ors) Wash lin producers and lin collec ors
separa ely.
3. Caring before loading
 Caring before washing
 Before the first washing
 Combine large and small items in a load. Load large items first. Large items should not be more than half
the total wash load.
Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.
• Check all pocke s o make sure ha hey
are emp y. I ems such as nails, hair clip,
ma ches, pens, coins and keys can damage
bo h your washer and your clo hes.
• Close zippers, hooks and s rings o
make sure ha hese i ems don’
snag on o her clo hes.
• Pre rea dir and s ains by brushing a li le
de ergen dissolved in wa er on o s ains like
collars and cuffs o help shif dir .
Selec a cycle (COTTON 60°C, add a half load of de ergen ) allow he uni o wash
wi hou clo hing. This will remove residues and wa er from he drum ha may have been lef
during manufac uring.
• Check he folds of he flexible gaske (gray) and
remove any small ar icles,if any.
• Check inside of he drum and remove any lef
i ems in i for nex wash cycle.
• Remove any clo hing or i ems on he flexible
gaske o preven clo hing and he gaske
damages.

12
dding detergent
A
• Main wash only ➔
• Pre Wash + Main Wash ➔
• Do no exceed he maximum fill line.
Close he dispenser drawer slowly.
Overfilling can cause early dispensing
of he fabric sof ener which could s ain
clo hes.
• Do no leave he fabric sof ener in he
de ergen drawer for more han 2 days.
(Fabric sof ener could harden)
• Sof ener will au oma ically be added
during he las rinse cycle.
• Do no open he drawer when wa er is
supplied.
• Solven s(benzene, e c) are no
allowable.
1. The Dispenser Drawer
2. Adding Fabric Softener
 Adding detergent and fabric softener
Do not pour fabric softener
directly on the cloths
NOTE
MAX
max

13
dding detergent
A
• The detergent sh uld be used acc rding t the
instructi n f the detergent manufacture.
• If t much detergent is used, t many suds
can ccur and this will decrease the washing
result r cause heavy l ad t the m t r.
• Use p wder detergent nly f r the fr nt
l ading washer.
❇ If suds ccur t much, pleas reduce the
detergent am unt.
• De ergen usage may need o be adjus ed
for wa er empera ure, wa er hardness,
size and soil level of he load. For bes
resul s, avoid oversudsing.
4. Water softener
• A wa er sof ener, such as An i limescale
(Calgon) can be used o cu down on he
use of de ergen in ex remely hard wa er
areas. Dispense according o he amoun
specified on he packaging.
Firs add de ergen and hen he wa er
sof ener.
• Use he quan i y of de ergen as for sof
wa er.
❋ Tips
Full load : according to
manufacturer’s recommendation.
Part load : 3/4 of the normal
amount.
Minimum load : 1/2 of full load.
• De ergen is flushed from he dispenser
a he beginning of he cycle.
1) Open he door and Table s in o he
drum.
3. Detergent dosage
5. Using the Tablets
MAX
max
2) Load he laundry in o he drum.
3) Close he door.

14
unction
F
 Recommended courses according to the laundry type
❋Water Temperature : Selec he wa er empera ure o he wash cycles.
Always follow garmen manufac ure’s care label or ins ruc ions when laundering.
❋Medic Rinse : For high effec iveness or more puri y in rinse opera ion you can choose Medic Rinse op ion.
❋Pre Wash : If he laundry is heavily soiled, “Pre Wash” Course is recommended.
❋Intensive : When washing heavily soiled laundry you can increase effec iveness by choosing “In ensive” op ion.
❋Program se ing wi h “Co on 60˚C+ In ensive” op ion for es in accordance or in conformi y wi h EN60456 and
IEC60456.
❋Crease Care : If you wan o preven crease, selec Crease Care bu on.
Cotton Quick
Synthetic
Quick 30
Bio Care
Duvet
Hand Wash /
Wool
Boiling Care
Bulky
Baby Care
Co on which is ligh ly soiled
Polyamide, Acryic, Polyes er
Colored Laundry which is ligh ly
soiled fas .
For elimina ion of remnan
de ergen af er boiling wash
For elimina ion of pro ein s ains
Hand wash marked delica e and
machine wash wool laundry
Co on bedding wi h filling duve ,
pillow, blanke , sofa cover wi h
ligh filling
Delicate Delica e laundry easily damaged
(silk, cur ains...)
Thick laundry absorbing much
wa er(Jumper)
Laundry for infan
60˚C
(95˚C)
30˚C
( Cold )
60˚C
(40˚C, 95°C)
40˚C
(
Cold
, 30˚C,
60˚C)
30˚C
(
Cold , 40˚C)
95˚C
40˚C
(
Cold, 30˚C)
-
Medic Rinse
- In ensive
- Pre Wash
- Crease Care
-
In ensive
- Crease Care
- In ensive
- Pre Wash
- Crease Care
Less han
8.0 kg
Less han
8.0 kg
1 king size
(9 dog)
Less han
6.0 kg
Less han
8.0 kg
Less han
2.0 kg
Less han
4.0 kg
Less han
8.0 kg
Less han
2.0 kg
Less han
2.0 kg
Program Fabric Type Proper Temp. Option Maximum Load
Cotton
Color fas garmen s
(shir s, nigh dresses,
pajamas...)and ligh ly soiled whi e
co on(underwear)
60˚C
( Cold , 30˚C,
40˚C, 95°C)
- Medic Rinse
- In ensive
- Pre Wash
- Crease Care
Less han
8.0 kg
❋ Notes : Neu ral de ergen is recommended.
The wool cycle fea ures gen le umbling and low-speed spin for garmen care.
The wool wash cycle of his machine has been approved by Woolmark for he washing of machine
washable Woolmark produc s provided ha he produc s are washed according o he ins ruc ions
on he garmen label and hose issued by he manufac urer of his washing machine M0708.

15
ow to use washer
H
• Press he Po er bu on o s ar .
• Press he Start/Pause bu on.
• Ini ial condi ions
- Wash : main wash
- Rinse : 3 times
- Spin :
• 1400 rpm
[F1422TD(1~9)]
• 1200 rpm [F1222TD(1~9)]
• 1000 rpm [F1022TD(1~9)]
- Water temperature : 60˚C
- Program : C tt n
• Press he Po er bu on o s ar .
• Selec he condi ions which you wan o use,
by urning he program dial and pressing
each bu on.
For selecting the each conditions, please refer to
the page16~page21
• Press he Start/Pause bu on.
1. Cotton automatically
selected upon power on.
2. Manual Selecting
3. Beep on/off
• The Beep on/off func ion can be se by
pressing and holding he TIme Delay bu on
simul aneously.
• The Beep on/off func ion can be se a any
ime and i is au oma ically canceled when
power failure.
Also he Beep on/off func ion works when
power is off.

16
ow to use washer
H
(1) Dial : Program
(2) Bu on : S ar / Pause
(3) Bu on : Spin
(4) Bu on : Tempera ure
(5) Bu on : Power
(6) Bu on : Medic Rinse
(7) Bu on : Pre Wash
(8) Bu on : In ensive
(9) Bu on : Crease Care
(10) Child Lock
(11) Tub Clean
(12) Bu on : Time Delay
1. Power
2. Initial Program
Power
• Press he Power bu on o urn power on and off.
• To cancel he Time Delay func ion, he power
bu on should be pressed.
• When he Power bu on is pressed, he
washer is ready for Co on program. And he
o her ini ial condi ions as follows.
• So, if you wan o advance in o he ashing
cycle wi hou changing he program, jus
press he Start/Pause bu on and hen he
washer will proceed.
■ Initial program
• [F1422TD(1~9)]
- C tt n Pr gram / Main wash /
N rmal Rinse / 1400 rpm / 60˚C
• [F1222TD(1~9)]
- C tt n Pr gram / Main wash /
N rmal Rinse / 1200 rpm / 60˚C
• [F1022TD(1~9)]
- C tt n Pr gram / Main wash /
N rmal Rinse / 1000 rpm / 60˚C
Program
• 13 programs are available according o he
laundry ype.
• Lamp will ligh up o indica e selec ed program.
• When Start/Pause bu on is pressed, he
Co on program is au oma ically selec ed.
- By urning he Program dial, he program is
selec ed in order of
“ Co on – Co on Quick – Syn he ic – Duve –
Bulky – Quick 30 – Rinse+Spin – Spin –
Delica e – Hand Wash/Wool – Bio Care –
Boiling Care – Baby Care”.
Regarding to the laundry type for each program
Please refer to the page14.

17
ow to use washer
H
Start/Pause
Detecting
• This Start/Pause bu on is used o s ar
wash cycle or pause he wash cycle.
• If emporary s op of wash cycle is
needed, press he Start/Pause bu on.
• When in Pause, he power is urned off
au oma ically af er 4 minu es.
• NB. The door will no open before 1 o 2
minu es when Pause is selec ed,
or a he end of he wash cycle.
1. Start
2. Pause
• While he "De ec ing" is shown in he display
he machine ro a es slowly and de ec s how
many laundries are loaded in he drum. I will
ake a few seconds.
• Available in Co on, Co on Quick and Syn he ic.
Door Lock
• Ligh s whenever he door of he washer is
locked.
• The door can be unlocked by pressing he
S ar /Pause bu on o s op he washer.
• The door can be opened af er a shor delay.
Option
• By pressing he
Op ion bu on, all
Op ion func ions
may be selec ed.
2. Pre Wash
• If he laundry is heavily soiled, “Pre Wash”
course is effec ive.
• Pre Wash is available in Co on, Co on
Quick, Syn he ic, Bio Care, Baby Care and
Boiling Care.
1. Medic Rinse
• For high effec iveness or more puri y in rinse
opera ion you can choose Medic Rinse
op ion.
• I can be chosen in all course wi h he
excep ion of Co on Quick, Quick 30,
Hand Wash/Wool, Duve , Delica e and Bulky.
4. Crease Care
• If you wan o preven crease, selec his
bu on wi h spin speed.
The required lamp will light up for identification.
3. Intensive
• If he laundry is heavily soiled “In ensive”
op ion is effec ive.
• By selec ing he In ensive op ion, he wash
ime may be ex ended, depending on he
program selec ed.

18
ow to use washer
H
Child Lock
If you choose o lock he bu ons on he con rol
assembly o preven ampering his func ion
may be selec ed.
• Child Lock can be se by pressing he Medic
Rinse bu on and Pre Wash bu on
simul aneously. (Abou hree seconds)
•
To deac iva e Child Lock sys em, press
Medic Rinse and Pre Wash bu ons
simul aneously again. (Abou hree seconds)
• To change o he desired program, whils in
child lock mode.
1. Press bo h
Medic Rinse and Pre Wash
oge her once again. (Abou hree seconds)
2. Press he Start/Pause bu on.
3. Selec he desired program and press he
Start/Pause bu on again.
• The child lock can be se a any ime and i
can be deac iva ed only by using child lock
cancel process. Turning he power off and
opera ional errors will no affec child lock.
Tub Clean
Tub Clean course can be se by pressing
and holding In ensive and Pre Wash bu on
simul aneously.
When Tub Clean course is se , display
“ ”, and all bu ons are inoperable.
TUB CLEAN is special cycle o clean he
inside of he washer. This cycle uses higher
wa er level wi h higher spin speed. Perform
his cycle regularly.
Ho to use the Tub Clean cycle:
1. Remove any clo hing or i ems from he
washer and close he door.
2. Open he dispenser drawer and add An i
limescale (Calgon) o he Main wash
compar men .
NOTE: Do no add any de ergen o he
de ergen compar men s. Excessive
suds may genera e and leak from he
washer.
3. Close he dispenser drawer slowly.
4. Power On and hen press and hold
In ensive and Pre Wash bu on for 3 seconds.
hen “ ” is displayed in LED
5. Press he S ar /Pause bu on o s ar .
6. Af er he cycle is comple e, leave he door
open o dry around he washer door
opening, flexible gaske and door glass.
CAUTION: If here is a small child, be
careful no o leave he door
open for oo long.
!

19
ow to use washer
H
Spin
[F1222TD(1~9)] [F1022TD(1~9)]
[F1422TD(1~9)]
2. No spin
3. Rinse Hold
• Rinse Hold is selec ed by pressing he
spin bu on repea edly his func ion
leaves clo hes in he machine;
suspended in he wa er af er a rinse
wi hou en ering in o spin.
• To proceed hrough o a drain or spin,
once he rinse hold func ion is comple ed
using o Program dial and Spin bu on o
he required program.
(Spin)
The required lamp will light up for
identification.
• If No spin is selec ed, he washer s ops
af er draining wa er.
1. Spin selection
• Spin Speed is available according o
he program as follows.
F1422TD(1~9)
- Cotton, Cotton Quick, Rinse+Spin, Quick 30,
Bio Care, Bulky, Spin
Rinse Hold - No Spin - 400 - 800 - 1400
- Delicate, Duvet, Baby Care, Boiling Care,
Synthetic, Hand Wash/Wool
Rinse Hold - No Spin - 400 - 800
F1222TD(1~9)
- Cotton, Cotton Quick, Rinse+Spin, Quick 30,
Bio Care, Bulky, Spin
Rinse Hold - No Spin - 400 - 800 - 1200
- Delicate, Duvet, Baby Care, Boiling Care,
Synthetic, Hand Wash/Wool
Rinse Hold - No Spin - 400 - 800
F1022TD(1~9)
- Cotton, Cotton Quick, Rinse+Spin, Quick 30,
Bio Care, Bulky, Spin
Rinse Hold - No Spin - 400 - 800 - 1000
- Delicate, Duvet, Baby Care, Boiling Care,
Synthetic, Hand Wash/Wool
Rinse Hold - No Spin - 400 - 800
• Af er selec ing he spin course, he
spin speed can be chosen by
pressing he spin bu on.

20
ow to use washer
H
Water Temp.
• By pressing he Temp.
bu on, he wa er
empera ure can be
selec ed.
- Cold
- 30˚C / 40˚C / 60˚C / 95˚C
• Wa er empera ure can be selec ed
according o he program.
The required temperature lamp will light up
for identification.
For the more detailed information, please
refer to the page14.
Time Delay
Preparing washing before starting
“Time Delay”
- Turn on he wa er ap.
- Load laundry and close he door.
- Place he de ergen and fabric sof ener in
he drawer.
• How o se “Time Delay”
- Press Po er bu on.
- Turn he Program dial o selec
he program you require.
- Press Time Delay bu on and se he
desired ime.
- Press he Start/Pause bu on.
(“:” blinks.)
• If Time Delay bu on is pressed, “3:00” is
displayed. The maximum delayed ime is
19 hours and he minimum ime is 3 hours.
• Each pressing of he bu on advances on
ime delay by one hour.
• To cancel he ime delay, press he Po er
bu on.
• Time Delay is ‘expec ed ime’ from he
presen o he comple ion of washing cycle
or selec ed process (Wash, Rinse, Spin).
• According to the condition of water supply
and temperature, the delayed time and the
actual washing time may vary.