LIBRA S10 User manual
Libra-S10 20080123v1.0
Wireless Finger Sensor Presenter Mouse
User Guide
Thank you for purchasing Libra-S10, another great addition to our IONE innovative
creations. Please read this user guide for information on using this product. If you
have any questions, please visit us at the following website www.ione.com.tw ,
www.ione-usa.com or www.ione-europe.com .
Safety Notice
This product complies with IEC 60825-1, class I laser product.
Your product complies with FCC and CE rules.
Avoid Direct Exposure to laser beam.
This product has no serviceable parts. Use of controls or adjustments of procedures
other than the user guide may result in danger.
Introduction
Libra-S10 is an innovative presenter mouse, built with advanced finger sensor interface
that senses the movements of a person's finger on its surface. Libra-S10 is equipped
with multi function capabilities, perfect for your PowerPoint®applications. It works as
a remote slideshow presenter, a laser pointer, and also as a mouse to help you perform
effortless presentations.
Feature
•2.4 GHz RF wireless technology
•Multiple control buttons for (left/right key, page up/down, enter/escape, and
task switch)
•Built-in laser pointer
•800 dpi resolution precision finger sensor cursor control
•LED indicator for low battery alert
•Up to 10 meters operational range
•Low power consumption and smart power saving function
Package Contents
1. 2.4GHz Wireless Finger Sensor Presenter mouse
2. User Guide
3. Accessory Package (Carrying pouch & strap)
4. 2 AAA batteries
System requirements
IBM or Compatible PC System
Microsoft Windows 2000/XP/Vista
Hardware Installation
Step1: Insert 2 AAA batteries into the battery compartment with correct polarity.
Step2: Please refer to the +, - diagram inside the battery compartment.
Step3: Turn on your computer and plug the dongle receiver into a USB port of your
computer.
Step4: Your computer will detect this USB device automatically.
Key Definition:
1. Finger Sensor area
2. Enter/Escape powerpoint
mode
3. Mouse left button
4. Mouse right button
5. Laser pointer
6. Page up
7. Page down
8. Task switch *(Flip)
9. Power on/off
ID Setting:
The product has been pre-set in ID for radio frequency and dongle receiver are
already paired. It is not necessary to do the ID setting when you use Libra S10 for the
first time. However, in case you need to re-set the connection ID, please follow the
process below for setting.
Step 1: Plug the dongle receiver into your computer. For the best performance, please
plug the dongle receiver into the front USB port of your computer, or use a
USB extension cable to place the dongle receiver 20cm away from monitor,
speaker, power supply, USB hub and other RF interference sources.
Step 2: Plug in the dongle receiver .The LED will start to blink.
Step 3: Press the connect button on the bottom of the Wireless Presenter within 8
seconds after Step 2.
Step 4: The LED on the dongle receiver will blink faster for few seconds. This means
that ID setting is completed.
Note: 1. If the Wireless Presenter does not work properly, please go back to step 2.
2. If the ID is used by other users or devices, please go back to step 2.
Reminder: For optimal performance, please place the dongle receiver 20cm away
from other RF interference devices such as computer monitors and speakers.
When Battery Low LED indicator signals the battery level is low, please replace the
battery as soon as possible to ensure proper functioning.
Now, Enjoy and Have Fun!!!
Troubleshooting
Should you encounter any problem or question during the usage of this device, please
WARNING
Note: This equipment has been tested and found to comply with the limits
for a
Class B device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications however, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
˙Reorient or relocate the receiving antenna.
˙Increase the separation between the equipment and receiver.
˙Connect the equipment into an outlet on a circuit different from
that to which the receiver in connected.
˙Consult the dealer or an experienced radio / TV technician for
technician for help.
Notice:
Changes or modifications not expressly approved by the part
responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two condition: (1) this
device may not cause Harmful interference, and (2) this
device must accept any interference Received, including
interference that may cause undesired operation.
Table of contents
