lidl HG00783A-TX User manual

5US-EN
Description of signal words.................................................................Page 6
Customer service .........................................................................................Page 6
Introduction.....................................................................................................Page 7
Intended use.......................................................................................................Page 7
Parts and features ..............................................................................................Page 7
Contents..............................................................................................................Page 9
Technical data....................................................................................................Page 9
Important safety notes............................................................................Page 10
Safety warnings for batteries ............................................................................Page 12
Assembly...........................................................................................................Page 15
Preparing for use ........................................................................................Page 15
Inserting/replacing the batteries......................................................................Page 15
Synchronizing transmitter/receiver..................................................................Page 16
Setting the signal type .......................................................................................Page 17
Setting the volume..............................................................................................Page 18
Selecting the chime............................................................................................Page 18
Connecting the transmitter to existing bell systems or an existing
doorbell button...................................................................................................Page 19
Connecting the transmitter to an existing bell system......Page 19
Connecting an existing doorbell button......................................Page 20
Troubleshooting...........................................................................................Page 20
Cleaning and maintenance...................................................................Page 21
Disposal .............................................................................................................Page 21
Three year limited warranty...............................................................Page 22
320257_silv_Design-Funktuerklingel_content_US.indd 5 01.03.19 12:13

6 US-EN
DESCRIPTION OF SIGNAL WORDS
WARNING indicates a hazardous
situation that, if not avoided, could
result in death or serious injury.
CAUTION indicates a hazardous
situation that, if not avoided, could
result in minor or moderate injury.
NOTICE indicates information con-
sidered important, but not hazard
related (e.g. messages related to
property damage).
CUSTOMER SERVICE
Call customer service at 1 [phone]
Visit the Website Customer Service Platform at
www.lidl.com/contact-us
Visit a LIDL store for further assistance.
IAN 320257 Please have your IAN number ready.
320257_silv_Design-Funktuerklingel_content_US.indd 6 01.03.19 12:13

7US-EN
Wireless Doorbell
Introduction
Congratulations on your purchase. You have selected a quality product.
The instructions for use are a part of the product. They contain import-
ant information about the safety, use and disposal of the product. Be-
fore using the product, please learn about all the safety information
and usage instructions. Only use the product as described and for the
specified applications. If you lend the product to someone else, please
also give all the instructions.
Intended use
This product is intended for the wireless transmission of the doorbell
signal. The product is not intended for commercial use.
Receiver: Indoor use only
Transmitter: Outdoor use (IP44)
Parts and features
Receiver
1Signal indicator
2Speaker
320257_silv_Design-Funktuerklingel_content_US.indd 7 01.03.19 12:13

8 US-EN
3Signal type selector button (acoustic, optical, optical and acoustic
signal)
4Melody selection button
5Volume/ Synchronization button
6Battery compartment cover
7Hanger
8Battery compartment
Transmitter
9Chime button
10 Name plate
11 Lock
12 Holder (for wall mounting)
13 Battery compartment
14 Inner cover
Mounting
15 Screw
16 Rubber cover
17 Screw
18 Dowel
19 Cable exit hole
20 Cable holder
320257_silv_Design-Funktuerklingel_content_US.indd 8 01.03.19 12:13

9US-EN
Contents
1 Transmitter
1 Receiver
3 Batteries 1.5V (direct current), type AA (receiver)
1 Battery 3V (direct current), type CR2032 (transmitter)
3 Screws (for transmitter and for mounting the receiver on a wall)
3 Dowels
5 Name plates (for the doorbell)
1 Set of operating instructions
Technical data
Model No: HG00783A-TX, HG00783A-RX
HG00783B-TX, HG00783B-RX
FCC ID: 2AJ9O-783TX
Range: 492ft. (150m) (unobstructed area)
Transmission frequency: 434 MHz
Transmission power: <10dBm
Battery types: Receiver: 3 x 1.5 V (direct current)
(type AA/LR6),
Transmitter: 1 x 3V (direct current)
(type CR2032)
Receiver: Audible signal volume (at maximum volume
setting): 73dB (at a distance of 3.2ft
(1m) from the device)
320257_silv_Design-Funktuerklingel_content_US.indd 9 01.03.19 12:13

10 US-EN
Ingress protection rating of the transmitter: IP44 (splash water
proof)
IMPORTANT
SAFETY NOTES
READ ALL INSTRUCTIONS. KEEP FOR FUTURE REFERENCE. IN-
CLUDE ALL DOCUMENTATION WHEN PASSING THIS PRODUCT
ON TO OTHERS.
Failure to observe the following warn-
ings may result in death or serious injuries.
DANGER TO LIFE AND RISK OF ACCIDENTS FOR IN-
FANTS AND CHILDREN! Never leave children unsupervised
with the packaging material. There is always a risk of suffocation
if children play with the packaging material. Children frequently
underestimate the dangers. Always keep children away from the
packaging material. This product is not a toy.
This product is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the product by a person responsible
for their safety. Children should be supervised to ensure they do
not play with the product.
320257_silv_Design-Funktuerklingel_content_US.indd 10 01.03.19 12:13

11US-EN
Changes or modifications to this product not expressly approved
by the party responsible for compliance could void the user‘s
authority to operate the product.
Note: This product has
been tested and com plies with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide rea
sonable protection a gainst
harmful interference in a residential installation. This product gen-
erates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with
the instructions, may caus e
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this product causes harmful interference
to radio or television reception, which can be determined by turn-
ing the product off and on, the user is encouraged to try and cor-
rect the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation
between the equip ment and receiver.
• Connect the product into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for
help.
This product complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This product may not cause harmful interference, and
(2) this product must accept any interference received, including
interference that may cause undesired operation.
320257_silv_Design-Funktuerklingel_content_US.indd 11 01.03.19 12:13

12 US-EN
Please note that the warranty does not cover damage due to
abuse, failure to observe the instructions for use and safety notes
or unauthorized use.
The RF exposure compliance distance is 0.79in (20 mm).
Safety warnings for
batteries
When used correctly, cells and batteries provide a safe and dep end-
able source of portable power. However, if they are misused or
abused, this may result in leakage, burns, fire, or explosion.
Store batteries in a dry place at room temperature. Batteries are
sensitive to high and low temperatures. Such thermal exposure
may lead to leakage, fire, or explosion.
Keep cells and batteries out of reach of children, especially small
batteries. Ingestion may lead to choking or acute and serious per-
sonal injury.
Keep cells or batteries clean and dry both during use and storage.
Wipe metal terminals with a soft, dry cloth if they become dirty.
Immediately seek medical attention if a cell or battery has been
swallowed. Also, contact your local poison control center.
In the event that the electrolyte comes into contact with the skin or
eyes, immediately flush with fresh water for at least 15 minutes
and seek medical attention.
Store unused batteries in their original packaging or in safe place
and away from metal objects that may short-circuit them.
320257_silv_Design-Funktuerklingel_content_US.indd 12 01.03.19 12:13

13US-EN
Exercise care in handling batteries in order to prevent shorting with
conducting materials, such as rings, coins, bracelets, and keys. The
battery or the conductor can overheat and cause burns, leakage,
fire, or explosion.
Clean the battery contacts and also those of the product prior to
battery installation. Keep the contacts clean.
Remove batteries from the product that will not be used for an
extended period of time (months or longer).
Remove discharged batteries from product promptly to avoid
possible damage from leakage.
Choose the proper battery for the intended application.
Always take care to correctly insert batteries observing (+) and (-)
polarity marks on the battery and the product for which it is int ended.
Proper polarity must be observed to avoid damage to either product
or batteries.
Always replace the whole set of batteries at one time, taking care
not to mix old and new ones, or batteries of different types, capacities ,
or manufacturers.
Never heat batteries in order to revive them.
Never charge a battery unless the battery label specifically states
the battery is rechargeable. Charging a non-rechargeable battery,
may result in leakage, fire, or explosion.
Do not open or mutilate a battery or cell. Electrolyte from the cell
is corrosive and can cause damage to the eyes or skin. The cell
contents can also be hazardous if ingested.
Do not drop or subject the cell or battery to strong mechanical
shock.
320257_silv_Design-Funktuerklingel_content_US.indd 13 01.03.19 12:13

14 US-EN
Batteries should not be disassembled, crushed, punctured, or
otherwise mutilated. Such abuses may result in leakage, fire, or
explosion.
Do not dispose of the battery in a fire. Failure to observe this
precaution may result in an explosion.
Dispose of batteries properly and in accordance with government
regulations.
WARNING
Chemical Burn Hazard.
0-5
DANGER if swallowed
Keep batteries away from children.
This product contains lithium button/coin cell batteries.
If a new or used lithium button/coin cell battery is swallowed
or enters the body, it can cause severe internal burns and can
lead to death in as little as 2 hours. Always completely secure
the battery compartment. If the battery compartment does not
close securely, stop using the product, remove the batteries,
and keep it away from children. If you think batteries might
have been swallowed or placed inside any part of the body,
seek immediate medical attention.
Dispose of button/coin cell batteries properly. Keep them
away from children. Even used cells may cause injury.
SAVE THESE INSTRUCTIONS
320257_silv_Design-Funktuerklingel_content_US.indd 14 01.03.19 12:13

15US-EN
Assembly
Note: You will need a screwdriver and a drill to assemble the product.
Note: Only use the screws and dowels supplied for the assembly of
the product.
Mount the receiver (see Fig. D).
Mount the transmitter (see Fig. E).
Preparing for use
For first time use, please remove the protective film from the name
plate of the transmitter and insert your name plate into the recess
on the transmitter.
Replace the protective film on the transmitter.
Inserting/replacing the batteries
Insert the batteries to provide power to the product before preparing
it for use.
Use the indicated battery types only. Failure to observe this advice
may result in product damage.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN
INCORRECT TYPE.
320257_silv_Design-Funktuerklingel_content_US.indd 15 01.03.19 12:13

16 US-EN
Receiver (see Fig. B):
Remove the battery compartment cover 6from the back of the
receiver.
Remove the used battery, if present.
Insert 3 batteries (1.5V (direct current), type AA).
Note: Ensure correct polarity. This is indicated in the battery
compartment 8.
Close the battery compartment cover 6.
Transmitter:
Remove the name plate from the holder 12 by pressing the lock
11 and remove the rubber cover 16 (see fig. C1).
Remove the used batteries, if present (see fig. C2).
Insert a battery (3 V (direct current), type CR 2032). The side
marked “+” must face up.
Re-install the rubber cover 16 , close the holder 12 of the transmitter
on to the back of the product.
Fasten the holder, and place screw 15 of the transmitter back on
to the back of the product & name plate.
The transmitter battery compartment with the holder must be in-
stalled using the screw 15 while in use. If the holder is damaged,
stop using the product.
Synchronizing transmitter/receiver
The product works on 434MHz which is a quite common frequency.
To ensure that the function is not influenced by doorbells in the
320257_silv_Design-Funktuerklingel_content_US.indd 16 01.03.19 12:13

17US-EN
neighborhood, the transmitter and the receiver have to be synchronized
via encryption. Every transmitter functions with a different signal en-
cryption.
Synchronize the transmitter and receiver as follows:
As soon as the batteries are installed, the receiver enters synchro-
nizing mode for 1 minute. During synchronizing mode, the signal
indicator 1steadily lights up blue.
You can also manually enter synchronizing mode by holding the
synchronizing button 5for 3 seconds.
The signal indicator 1on the receiver will steadily light up for
1 minute, to indicate that the receiver is in synchronizing mode.
Press the chime button 9of the transmitter, while the receiver is
in synchronize mode. If the receiver receives the signal, the steady
blue light of the signal indicator 1flickers 6 times to indicate
that the synchronization is successful.
Setting the signal type
The receiver can indicate the reception of a door signal either both
optically and acoustically, or only acoustically, or only optically.
Using the signal type selector button 3, select whether the signal
is to be indicated both optically and acoustically or acoustically
or optically.
Press the signal type selector button 3once. An acoustic signal
will sound and afterward the signal indicator 1will flash. The re-
ceiver will now indicate the door signal acoustically and optically.
320257_silv_Design-Funktuerklingel_content_US.indd 17 01.03.19 12:13

18 US-EN
Press the signal type selector button 3again. An acoustic signal
will sound. The receiver will now indicate the door signal acousti-
cally. Press the signal type selector button 3again. The receiver
will now indicate the door signal optically.
When the receiver battery is drained, the signal indicator will flash.
You can replace the used battery with a new one of the same type.
Setting the volume
Press the volume button 5until the desired volume is reached.
There are a total of 4 possible volume settings: very loud, loud,
medium, soft.
Selecting the chime
Note: The product has 16 different chimes.
Press the melody selection button 4. The first audible signal
sounds.
Press the melody selection button 4again to move on to the
next audible signal.
Repeat this process until you have selected your desired audible
signal. The last-selected audible signal is automatically stored.
320257_silv_Design-Funktuerklingel_content_US.indd 18 01.03.19 12:13

19US-EN
Connecting the transmitter to existing bell
systems or an existing doorbell button
Remove the holder 12 by pressing the lock 11 from the back of
the transmitter and remove the rubber cover 16 (see fig. C1).
Open the inner cover 14 using a Phillips screwdriver (see fig. F).
Remove the plastic clip of cable exit hole 19 with a flat head
screw driver (see fig. G).
Insert the cable through cable holder 20 and cable exit hole 19
(see fig. H).
Connect cable to terminals A and C (for connecting to existing
doorbell) or terminals B and C (for connecting to existing doorbell
button) using screw driver (see fig. H).
Connecting the transmitter to an existing
bell system (see Fig. I)
Extension of an existing doorbell system:
An already existing doorbell system can be extended with this product.
The operating voltage of the doorbell system must be between 4–12V.
It makes no difference whether this comes from direct current or 50 -
60Hz alternating current. In the event that you are dealing with an
existing doorbell system using direct current, you must connect the
positive terminal of the doorbell to contact C of the transmitter and
the negative terminal to contact A of the transmitter.
320257_silv_Design-Funktuerklingel_content_US.indd 19 01.03.19 12:13

20 US-EN
IMPORTANT! Never reverse polarity. Doing so may damage the
product.
The connection terminals A and C, found on the circuit board of the
transmitter as shown in fig. I must be connected directly to the electrical
connection terminals of the signal generators (e.g. bell). The button of
the transmitter may also be used for this type of operation.
Note: Contact a qualified electrician in case of problems during
installation.
Connecting an existing
doorbell button (see Fig. J)
The separate bell button must not be connected to the existing doorbell
system. The battery must remain in the transmitter. For this purpose,
terminals B and C are connected to the bell button with a two-core
cable. The bell push may only be connected to the transmitter.
Troubleshooting
In case of extraordinary environmental influences (e.g. a strong elec-
tromagnetic field) the function of the product may be affected. In this
case, please remove the batteries from the transmitter and the receiver
for approximately 2 minutes. Then proceed again as described in the
section “Synchronizing the transmitter/ receiver”.
320257_silv_Design-Funktuerklingel_content_US.indd 20 01.03.19 12:13

21US-EN
Electrostatic discharges may lead to malfunctions. If such malfunctions
do occur, remove the batteries for a short time and then replace them
again. Then proceed again as described in the section “Synchronizing
the transmitter/receiver”.
Cleaning and maintenance
Never use liquids or detergents to prevent product
damage.
Only clean the outside of the product using a soft, dry cloth.
Disposal
Dispose of the packaging through your local recycling facilities and in
compliance with all federal, state and local regulations.
b
a
Please note the package markings regarding waste sepa-
ration, indicated by abbreviations (a) and numbers (b),
meaning: 1–7: plastics/20–22: paper and cardboard /
80–98: composite materials.
Contact your local waste management authority for addi-
tional information on how to dispose of the used product.
To help protect the environment, please dispose of the product properly
when it has reached the end of its useful life, do not throw in the
320257_silv_Design-Funktuerklingel_content_US.indd 21 01.03.19 12:13

22 US-EN
garbage. Information on collection sites and their opening hours is
available from your local authority.
Improper disposal of batteries can damage the
environment!
Never throw batteries in the garbage. They may contain toxic heavy
metals and must be handled as special waste. The chemical symbols
of heavy metals are: Cd = cadmium, Hg = mercury, Pb = lead. Used
batteries should therefore be disposed of through a local collection
point.
Three year limited warranty
What does this warranty cover?
The warranty covers:
· Damage, breakage or inoperability due to defect.
· Damage not caused by normal wear and tear or failure to follow
the safety and maintenance instructions provided in the user manual.
What is not covered by the warranty?
The warranty does not cover damage caused by:
· Normal wear and tear of the product, including fragile parts (such
as switches, glass, etc.);
· Improper use or transport;
· Disregarding safety and maintenance instructions;
· Accidents or acts of nature (e.g. lightning, fire, water, etc.);
320257_silv_Design-Funktuerklingel_content_US.indd 22 01.03.19 12:13

23US-EN
· Tampering with the product (such as removing cover, unscrewing
screws etc.).
Consequential and incidental damages are also not covered under
this warranty. However, some states do not allow the exclusion or
limitation of incidental or consequential damages, so this limitation
or exclusion may not apply to you.
What is the period of coverage and warranty resolution?
The warranty is for 3 years from the date of purchase. At our discretion,
product will either be refunded or replaced.
What will we not do?
We will not:
· Start a new warranty period upon product exchange;
· Repair product.
How to process the warranty?
To initiate, please:
· Call customer service at 1 [phone]
· Visit the Website Customer Service Platform at
www.lidl.com/contact-us
or
· Visit a LIDL store for further assistance
320257_silv_Design-Funktuerklingel_content_US.indd 23 01.03.19 12:13

24 US-EN
To ensure the quickest warranty return process, please have the
following available:
· The original sales receipt that includes the date purchased;
· The product and manual in the original package;
· A statement of the problem.
What must you do to keep the warranty in effect?
· Retain the original receipt;
· Follow all product instructions;
· Do not repair or modify the product.
How does state law relate to this warranty?
This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state. All implied warranties are
limited by the duration and terms of this warranty. Some states do not
allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you.
320257_silv_Design-Funktuerklingel_content_US.indd 24 01.03.19 12:13