lifelong AquaWash LLHPW17 User manual

GLIDE CEILING FAN
AquaWash
High Pressure
Washer
1 YEAR
WARRANTY
1700W
Powerful
Motor
5 Meter
Power
Cord
Max
Pressure
135 Bar
High
Performance
Copper Motor
High
Eciency
Spray Gun

Welcome to the Lifelong family,
Dear Customer,
Congratulations on purchasing Lifelong AquaWash High
Pressure Washer and a warm welcome to the Lifelong
family. At Lifelong, we take pride in developing quality prod-
ucts for your home, health and happiness. Through constant
innovation in our products, we have been able to develop a
wide spectrum of products across Home, Kitchen, Grooming
and Wellness categories. We strive to enrich the lives of the
modern consumer every day. Keeping that in mind, we have
offered all our products at a fair and honest price.
We hope that the High Pressure Washer serves you and your
family’s needs without any hassles.
Thanks again for becoming a part of the Lifelong family. Enjoy
using the product!
Warm Regards,
Team Lifelong
1. Model Overview
2. Technical Details
3. Important Safety Instructions
4. Assembly Instructions
5. Operating Instructions
6. Using the Accessories
7. Working with Detergents
8. Shutting Down and Clean-Up
9. Maintenance Instructions
10. Cleaning Tips
11. Troubleshooting
CONTENTSCONTENTS

indicates “an imminently hazardous situation which, if not avoided, will result in death or serious
injury.”
indicates “a potentially hazardous situation which, if not avoided, could result in death or injury.”
indicates “a potentially hazardous situa-tion which, if not avoided, may result in minor or moderate
injury or in property damage incidents.”
The owner and/or user must have an un¬derstanding of the manufacturer’s oper¬ating instructions
and warnings before using this pressure washer.
Warning information should be empha¬sized and understood.
Owner and/or user must study and maintain for future reference the manu¬facturers’ instructions.
For household use only!
MODEL OVERVIEW
SAFETY ALERT SYMBOLS
OWNER/USER RESPONSIBILITY

When using this product basic precautions should always be followed, including the following:
Read all the instructions before using the product.
■ To reduce the risk of injury, close supervision is necessary when a product is used near
children.
■ Know how to stop the product and bleed pressures quickly. Be thoroughly familiar with the
controls.
■ Stay alert - watch what you are doing.
■ Do not operate the product when fatigued or under the influence of alcohol or drugs.
■ Keep operating area clear of all persons.
■ Do not overreach or stand on unstable support. Keep good footing and balance at all times.
■ Follow the maintenance instructions specified in the manual.
■ This product is provided with a Ground Fault Circuit Interrupter built into the power cord plug.
If replacement of the plug or cord is needed, use only identical replacement parts.
Warning
Risk of Injection or Injury- Do Not Direct Discharge Stream at Persons.
■ High-pressure jets can be dangerous if misused. The jet must not be directed at persons,
animals, electrical devices, or the unit itself.
■ Wear safety goggles
Warning
Risk of Explosion - Do not spray flammable liquids.
■ Do not use acids, alkaline, solvents, or any flammable material in this product. These products
can cause physical injuries to the operator and irreversible damage to the machine.
Warning
■ Inspect cord before using - Do not use if cord is damaged.
■ Keep all connections dry and off the ground.
■ Do not touch plug with wet hands.
■ Do not use extension cord with this product.
■ Connect to individual branch circuit only.
IMPORTANT SAFETY INSTRUCTIONS
Model number LLHPW17
Model name AquaWash
Voltage/Frequency (V/Hz) 230/50
Working Pressure (Bar) 90
Max Pressure (Bar) 135
Motor Power (W) 1700
Rate Flow (L/min) 5.5
Max Flow (L/min) 7.5
Motor Type Universal
Pump RPM 3000

Improper connection of the equipment-grounding conductor can result in a risk of electrocution.
Check with a qualified electrician or service personnel if you are in doubt as to whether the
outlet is prop-erly grounded. Do not modify the plug provided with the product - if it will not fit the
outlet, have a proper outlet installed by a qualified electrician. Do not use any type of adapter
with this product.
This pressure washer is provided with a ground-fault circuit-interrupter (GFCI) built into the plug
of the power-supply cord. This device provides additional protection from the risk of electric
shock. Should replacement of the plug or cord become necessary, use only identical
replacement parts that include GFCI protection.
This pressure washer is provided with a ground-fault circuit-interrupter (GFCI) built into the plug
of the power-supply cord. This device provides additional protection from the risk of electric
shock. Should replacement of the plug or cord become necessary, use only identical
replacement parts that include GFCI protection.
When connecting the water inlet to the water supply mains, local regulations of your water
company must be observed. In some areas the unit must not be connected directly to the
public drinking water supply. This is to ensure that there is no feedback of chemicals into the
water supply. Direct connection via a receiver tank or backflow preventer, for example, is
permitted.
Dirt in the feed water will damage the unit. To avoid this risk, we recommend fitting a water filter.
■ Garden hose must be at least 13 mm or 16 mm (1/2 inch or 5/8) inch in diameter.
■ Flow rate of water supply must not fall below 7.6 L/min. (2 GPM/gallons per minute).
■ Flow rate can be determined by run-ning the water for one minute into an empty 20 litre
(5-gallon) container.
■ The water supply temperature must not exceed 40°C/104°F.
WATER SUPPLY (Cold Water Only)
This product must be grounded. If it should malfunction or breakdown, grounding provides a
path of least resistance for electric current to reduce the risk of electric shock. This product is
equipped with a cord having an equipment grounding conductor and a grounding plug. The
plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
■ Never use the pressure washer to draw in water contaminated with solvents, e.g. paint
thinners, gasoline, oil, etc.
■ Always prevent debris from being drawn into the unit by using a clean water source
Required tools:
Screwdriver, medium size (not supplied) for final assembly.
Assembly
ASSEMBLY INSTRUCTIONS
GROUNDING INSTRUCTIONS
GROUND FAULT CIRCUIT INTERRUPTER PROTECTION

Install the water inlet connector to the unit’s water inlet.
Note: Never attach the garden hose connector to the unit’s water inlet

Note: Make sure the connection nipple is aligned correctly. Check the connection by pulling on
the high- pressure hose.
Check the secure connection by pulling on the high-pressure hose
STEP 1:
Insert one end of the highpressure hose tightly into the quick connect on the unit, it will
lock in audibly.
STEP 2:
Insert the spray wand of your choice into the trigger gun. Press in against the spring tension
and twist into locked position.
STEP 3:
Screw the supplied garden hose connector on to the end of your garden hose.
OPERATING INSTRUCTIONS

STEP 4:
Push the garden hose connector on to the water inlet connector and make sure you hear it click
into place before proceeding.
STEP 6:
Plug the Ground Fault Circuit Inter-rupter (GFCI) into a receptacle. Press RESET button,
indicator should be “ON”.
Press TEST button, indicator should be “OFF”.
Press RESET button for use.
STEP 7:
Unlock the trigger gun safety lock. Trigger the gun to eliminate trapped air, wait for a steady flow
of water to emerge from the spray nozzle.
STEP 8:
Turn on the high-pressure washer (1/ ON).
The motor starts only if the trigger of the gun is pulled and shuts off when the trigger is released.
STEP 5:
Connect garden hose to the cold water source and turn water on com-pletely

For best results see Cleaning Tips for specific information on how to clean
different surfaces.
Never use:
- Bleach, chlorine products and other corrosive chemicals
- Liquids containing solvents (i.e., paint thinners, gasoline, oils)
- Tri-sodium phosphate products
- Ammonia products
- Acid-based products
These chemicals will harm the unit and will damage the surface being cleaned.
Use of these items will void the warranty.
STEP 1:
Install the Vario Power Spray Wand. Set the spray wand to the low-pressure setting (Mix).
STEP 2:
Fill the Detergent Tank with the selected detergent.
STEP 3:
Turn on the pressure washer (I). Pull trigger to operate unit. Liquid detergent is drawn into the
unit and mixed with water. Apply detergent to work area. Do not allow detergent to dry on
surface.
STEP 4:
To rinse, move the VPS out of "Mix" position and pull trigger to operate unit.
WORKING WITH DETERGENTS

STEP 5:
Cleaning up: Always draw fresh wa-ter through the detergent tank or siphon
tube when done to flush any remaining detergents from the injection
system.
STEP 1:
Turn the switch to OFF (0) position
STEP 2:
Turn off the water source.
STEP 3:
Press trigger to release water pres-sure.
STEP 1:
Release trigger and engage gun safety lock.
STEP 2:
Turn pressure washer to OFF (0) position.
SHUTTING DOWN AND CLEAN-UP
TAKING A BREAK ... fiveminutes or more