Lifemax FH1644119 User manual

MODEL: FH1644119
FINGERHUT
ASSEMBLY INSTRUCTIONS
ATTENTION
DO NOT RETURN
TO THE STORE
Contact
MD Sports
Customer Service
* For additional resources and Frequently
Ask Questions, please visit us at
themdsports.com

This product is covered by a limited warranty that is effective for 90 days from the date of purchase. If,
during the limited warranty period, a part is found to be defective or breaks, we will offer replacement part
at no cost to you, the customer. The only exceptions to the warranty include main frames, table tops,
playing surfaces, batteries or tools.
The above warranty will not apply in cases of damages due to improper usage, alteration, misuse, abuse,
accidental damage or neglect.
This Limited Warranty gives you specific legal rights and you may also have other rights which vary from
one State (province) to another.
A PURCHASE RECEIPT (or other proof of purchase date) will be required before any warranty service is
initiated. All requests for warranty service, please feel free to contact our Consumer Service Department at :
Please be aware of your product’s Limited Warranty for the return/refund policy from the store, We, at Medal
Sports, can not handle the product which is out of product’s limited warranty since we only provide available
parts. Thank you!
PLEASE CONTACT US BEFORE RETURNING
THE PRODUCT TO THE STORE.
WEBSITE: www.themdsports.com
NOTICE!
STAPLE YOUR RECEIPT HERE
1 - Please leave your name, address, phone number, model number, parts needed on the answering
machine if there is no attendant. Failure to do so will result in a delay in shipping parts to you.
2 - Please review the replacement parts list and make sure that you have all your parts before beginning
assembly. For questions that may arise or for missing/damaged parts, please contact us.
3 - Since you build all tables upside down, please inspect tabletops or playing surfaces right away before
putting together, all damaged table tops/playing surfaces need to be returned to the store. Please
contact with retailer for their return policy. Thank you very much.
www.themdsports.com
1644119 1
(Continued on the next page.)
LIMITED 90 DAYS WARRANTY

X2
Strong Adults Needed No Children in
Assembly Area
Keep away from pets Do not use or keep product
outdoors. For indoor use only.
No wet/humid conditions.
Power Tools
- Set Low Torque
High Torque
over tightened
TOOLS REQUIRED:
Phillips Screwdriver - Not Included
Standard (Flat Head Screwdriver) - Not Included
Wrench - Included
Allen Key - Included
CAUTION !
Electric Screwdrivers may be helpful during assembly;
however, please set a low torque and use extreme
caution.
WARNING:


!
WARNING: Adult Assembly Required.
!
ASSEMBLY TIPS:
1 - Please read the instructions carefully, and follow all assembly, operation or safety instructions properly in order to
avoid damage or injury. For the assembly, at least two adults are required.
2 - Some figures or drawings may not look exactly like your product. Please read and understand the text before
beginning each assembly step.
1 - This product is intended for INDOOR use only.
2 - Please Do Not sit, climb or lean on the product.
3 - Please Do Not drag the table when moving it in order to avoid the damaged on the legs.
4 - Please only use spray furniture polish to clean the exterior surfaces on the product.
5 - This is not a child's toy, adult supervision is required for children playing this game.
IMPORTANT NOTICE!
www.themdsports.com
1644119 2
(Continued on the next page.)

www.themdsports.com
1644119 3
(Continued on the next page.)
910 11 12
13 14 15 16
Net Net Post
2 3 41
x2 x2
6 7 85
x2 x2 x2
x6 x2
x1 x2
x2
Plastic Corner
18 19 20
Leg Bracket - A Leg Bracket - B
x8
21
Logo Panel with
Frame
x2
End Panel
(1.35m)
22
x2
Side Panel
(1.25m)
23
x4
Safety
Strap - Long
24
x1
25
Safety
Strap - Short
x2
Table Tennis
Paddle
26
x2
Table Tennis
Ball
27
x2
28
29
Wheel
x4
“T” Washer
x2
30 31
17
x4
1644119 PARTS LIST
x4
Table Surface - 1 Table Surface - 2
Linkage Tube
with Stop Bracket Linkage Tube
Bracket
Curved Outer Leg
with Cap
Curved Inner Leg
with Cap
Gravity Lock
M4 X 12mm
Screw
x47
x10
M6 X 50mm
Bolt
x8
M6 X 60mm
Bolt
x36
M6 Washer Spacer
x8 x18
M6 Nut
M5 X 12mm
Screw
x88 x1
Wrench Allen Key
x1

Outer Leg Cap Inner Leg Cap
P1 P2
x4 x4
1644119 PRE-INSTALLED PARTS
www.themdsports.com
1644119 4
(Continued on the next page.)
ASSEMBLY INSTRUCTIONS:
1. Find a clean, level place to begin the assembly of your Table Tennis Table Game. We recommend that two
adults work together to assemble this table tennis table game.
2. Remove all the parts from the box and verify that you have all of the listed parts as shown on the Parts
list page. Carefully cut or tear the four corners of the box so that the bottom of the box can be used as your
work surface.

www.themdsports.com
1644119 5
(Continued on the next page.)
9
14
23
Note: Align the inside seams of
each sections so that pre-drilled
holes line up across from each other.
Note: Center gap tolerance
approximately 10~13mm.
Player
Player
Center
9
29
FIG. 1A
FIG. 1
1 X 2
X 2
X 6
9
2
X 1
X 2
13
14
X 3
23
X 24
29
1
1
9
2
2
13
14
23
23
14 23
FIG.1
3. Place Table Surface - 1 (#1) and Table Surface - 2 (#2) with the painted surface facing down on a flat surface.
4. Connect Table Surfaces together using three Brackets (#9) using twelve Screws (#29). See FIG. 1 and 1A.
5. Attach the Safety Strap - Long (#13) and 2 Safety Straps - Short (#14) to Table Surfaces (#1 & #2) using three
Screws (#23). See FIG. 1.

www.themdsports.com
1644119 6
(Continued on the next page.)
FIG.2
5
6
X 2
X 2
29 X 64
19 X 8
20 X 4
P2 X 4
P1 X 4
Playerr
Player
Center
NOTE: Make sure that the
oval cut-out in the Leg
Bracket are facing the
center of the table for
proper installation.
FIG. 2
This is hole for “Gravity
Lock” assembly.
19 29
19
19
29
29
29
P2
P1
29
19
FIG. 2A
20
20
19
20
5
6
29
FIG. 2B
6. Place one Curved Outer Leg with Cap (#5) on the player end of the table half and one Curved Inner Leg with
Cap (#6) on the center end of the table half.
7. Attach the Leg Brackets (#19 & #20) to the Curved Outer Leg (#5) and the Curved Inner Leg (#6)
using Screws (#29). See FIG. 2A & 2B.
8. Repeat the above steps for the other table half.

www.themdsports.com
1644119 7
(Continued on the next page.)
X 2
X 2
7
8
30 X 1
X 8
28
X 1
31
24
X 16
X 8
26
X 8
27
Player
Player
Center
FIG. 3
28
31
24
24
26 26
26
26
27
27
7
7
8
8
30
31
5
5
6
6
FIG. 3B
28
FIG. 3A
30
Note: Be careful of the assembly
direction on pictures when you
assemble the Linkage Tube #7 and
#8 in order to fit the folding function.
FIG.3
9. Attach one end of the Linkage Tube (#8) to the inside of the Curved Outer Leg (#5) using one Bolt (#24), two
Washers (#26), one Spacer (#27) and one Nut (#28). See FIG. 3A.
10. Attach one end of the Linkage Tube with Stop Bracket (#7) to the inside of the Curved Outer Leg (#5) using
one Bolt (#24), two Washers (#26), one Spacer (#27) and one Nut (#28). See FIG. 3B.
11. Repeat the same for the other end of this Linkage Tube, only attaching it to the outside of the Curved
Inner Leg (#6).
12. Repeat the above steps for the other table half.

www.themdsports.com
1644119 8
(Continued on the next page.)
FIG. 4
X 4
X 44
X 2
X 4
17
23
11
12
Player
Player
Center
17
17
17
23
23
23
11
12
12
FIG.4A
FIG.4
13. Place the Plastic Corners (#17) flush with the table corners and attach using three Screws (#23) per
Corner. See FIG. 4A.
14. Place the End Panels (#11) between the corners and flush with the table edges at the Player ends of the
table and attach using five Screws (#23) per End Panel. See FIG. 4.
15. Place the Side Panels (#12) flush with the table edges at the sides of the table and attach using five
Screws (#23) per Side Panel. See FIG. 4.
16. Repeat above steps for other Table Surface.
NOTE: Make sure all Aprons are inside the Plastic Corners.

www.themdsports.com
1644119 9
(Continued on the next page.)
X 8
X 4
X 2
X 4
26
25
21
18
FIG. 5
X 4
28
26
P1
P2
Player
6
5
26
25
31
21
18
18
21
28
30
FIG.5
17. Make sure the Outer Leg Caps (P1) and Inner Leg Caps (P2) are installed into the ends of the leg.
Then place the Wheel (#18) into the Legs. See FIG. 5.
18. Attach the Logo Panel with Frame (#21) to the Curved Inner Leg (#6) using two Bolts (#25), four
Washers (#26) and two Nut (#28) per Frame. See FIG. 5.
NOTE: Do not tighten securely at this time.

www.themdsports.com
1644119 10
(Continued on the next page.)
CAUTION: Two strong adults are recommended to turn
the table over as shown.
B. FOLD LEGS AND
TABLE HALVES AND
LOCK IN PLACE
C. LIFT TABLE AND
TURN IN THE AIR
D. DO NOT LEAN
TABLE ON ITS LEGS!
A. TURN TABLE
ON ITS SIDE
ABCDE
FIG. 6
Warning
At least two adults
NOTE: Place on all 2 wheels at once
FIG. 6A FIG. 6B
FIG. 6C FIG. 6D
NOTE: Lift off of the floor and turn in the air.
E. SET TABLE DOWN EVENLY
ON ALL WHEELS, TO PREVENT
DAMAGING THE LEGS
DO NOT lean the table on it's legs!

www.themdsports.com
1644119 11
(Continued on the next page.)
X 8
X 4
26
25
FIG. 7
26
25
Note: Center gap tolerance
approximately 10~13mm.
21
Center
6
Player
5
26 31
28
X 4
28
30
FIG.7
19. Before turning the table over, make sure to push the Curved Inner Leg (#6) towards the center of the
table in order to fix leg in right position.
NOTE: Two adults are required to turn this table over.
20. One person should stand at each center of the table and turn the table over completely so that it rests on
its legs.
21. Standing at the sides of the table, place the two table halves so they are inches apart.
NOTE: Be careful that you do not push either half
backwards as this may cause the legs to fold!
22. Attach the Logo Panels with Frame (#21) to the opposite table half using two Bolts (#25), four Washers
(#26) and two Nuts (#28) per Frame. See FIG. 7.
Now go back and tighten all the connections.

www.themdsports.com
1644119 12
(Continued on the next page.)
HARDWARE AFTER ASSEMBLY
FIG. 8A
FIG. 8
24
24
24
X 4
X 2
X 2
X 2
10
10
10
28
28
28
26
26
26
26
X 2
22
22
22
6
6
Note: Please make sure the gravity
lock is locked when folded.
31
6
30
FIG.8
23. Attach the Gravity Locks (#10) to the Curved Inner Leg (#6) using one Bolt (#24), two Washers (#26), one
“T” Washer (#22) and one Nut (#28) per Gravity Lock. See FIG. 8A.

www.themdsports.com
1644119 13
(Continued on the next page.)
X 1
X 2
15
15
15
16
16
16
FIG. 9
FIG. 9A
16
FIG.9
24. Attach the Net Post (#16) at the middle of the table and slide the net over the post. Stretch the Net
(#15) across the center of the table and slip the net over the post on the opposite side. See FIG. 9A.

www.themdsports.com
1644119 14
(The last page)
NOTE: When the table is in its storage position, always attach the safety strap
to prevent the sides from falling.
YOU ARE NOW READY TO PLAY!
FIG. 10
FIG. 10C
Safety Straps
Reverse
FIG. 10A
FIG. 10B
13
10
14
1
2
Gravity Lock
FIG. 10D
Note: Please make sure the
gravity lock is locked when folded.
FIG.10
25. Engage the Wheels Lock.
26. Folding the table - First fold the side of the table without the Net Post. Hold the end securely and lift the
table. Make sure the Gravity Lock (#10) is locked. Repeat for the other side. Attach the Safety Strap Long
and short (#13, #14) together to prevent the sides from falling. See FIG. 10.
27. To unfold the table - First release the Gravity Lock (#10) and Safety Strap (#13 & #14). Then pull the bottom of
the outer leg and slowly lower the table to the floor.