Lifepro REJUVACURE User manual

REJUVACURE
FAR INFRARED SAUNA
USER MANUAL

HELLO THERE.
Joel and I are athletes who suffered from
severe ACL injuries a few months apart.
We purchased multiple pieces of wellness
equipment for our in-home rehab but were
left disappointed and frustrated by wellness
and recovery products that made big promises
but gave no support, no well-thought-out
plan to follow, and no results. And that’s how
Lifepro came about, and why the Wellness
Recovery collection was created — we’ve
set out to change all of that. It’s why every
piece of equipment bearing our name not only
undergoes rigorous scrutiny to make sure it
delivers on power and efficacy, but also comes
with built-in support from our ‘guiding angels’
and a built-in lifetime warranty so that
you’re never left hanging.
Welcome to Lifepro.
We’re in this together now.

With the Lifepro Rejuvacure Far Infrared Sauna, you can experience the myriad
therapeutic benefits of far infrared wavelengths from the comfort of your own home—
no need for expensive trips to the sauna or spa. Far infrared wavelengths raise your
internal body temperature, resulting in a deep, detoxifying sweat and allowing your
body to expel toxins like heavy metals. They also increase the heart rate and blood
flow, mimicking a workout and providing some of the same beneficial effects, including
increased metabolism and fat loss. It’s a great way to supplement your workout
routine. New scientific studies show that infrared therapy also boosts the immune
system and lowers the risks of cardiovascular disease, high blood pressure, and stroke.
The Rejuvacure is made from solid Canadian hemlock and is heated by energy-
efficient, zero-EMF carbon fiber heaters. The carbon heaters distribute heat evenly,
heat up quickly, and are more technologically advanced and last longer than ceramic
heaters. When heated, the carbon heaters emit far infrared waves (5.6–15 microns)
which penetrate up to an inch and a half into muscle and fat, warming your body from
the inside out. There is no hot air, so it’s less intense than a traditional sauna and
safer for sensitive skin. The Rejuvacure is perfect for anyone who wants to improve
their cardiovascular health, reduce pain from chronic conditions such as arthritis and
rheumatoid arthritis, improve skin health, lose inches around the waist, and reduce
stress.
The Rejuvacure Far Infrared Sauna has a built-in chromotherapy module which provides
seven color therapy modes, red, orange, yellow, green, cyan, blue, and violet, each
with a range of therapeutic benefits. You can connect a mobile device to the sauna's
speakers via Bluetooth to listen to music or podcasts during your sauna session. The
temperature is adjustable from 86–149 °F and you may set a treatment time from
1–60 minutes. Use the Rejuvacure 3 or 4 times a week for 30–45 minutes, and see
results in as little as one week. Enjoy detoxification, performance recovery, and pain
relief anytime, anywhere!
Redefine wellness and experience the transformative power of
the Lifepro Rejuvacure:
Alleviate pain: reduces muscle, joint, and chronic pain. Heals injuries quickly.
Increase metabolism: encourages your body to burn fat and lose inches.
Reduce inflammation: improves blood flow and lowers blood pressure.
Rejuvenate skin: stimulates cells to create new proteins and regenerate cells.
Boost mood: decreases stress and increases serotonin levels.
Check out the information in this manual for ways to get started using the Rejuvacure
Far Infrared Sauna. Next, be sure to visit our website rejuvacure.lifeprofitness.com for
access to our FREE library of videoswhich demonstrate how to easily incorporate the
Rejuvacure into your health and wellness routine.
Wellness Recovery Collection 5
GET STARTED
FIRST STEPS
1. Remove the components and hardware from the shipping box and
inspect items for shipping damage.
CAUTION: Visually inspect all heaters for shipping damage before
assembly. Do not operate the sauna with damaged heaters. If any damage
is detected, contact a support representative.
2. Compare the parts and hardware to the items listed in WHAT’S IN THE
BOX on the next page.
3. Read carefully through this user manual and all SAFETY
INSTRUCTIONS (beginning on page 30) before assembling and using
your Rejuvacure.
4. Go to rejuvacure.lifeprofitness.com and register your sauna within
14 days of purchase to activate your lifetime warranty.
5. Assemble the sauna following the steps in the SIMPLE SAUNA
ASSEMBLY GUIDE on pages 9–21.
6. See TIPS FOR USING THE REJUVACURE on page 22 and OPERATING
INSTRUCTIONS on page 24.
CAUTION:
• Always use proper lifting techniques, the shipping box is quite heavy.
• Two adults are required to assemble this sauna.
CUSTOMER SUPPORT
If you have any questions about assembling or using the Rejuvacure,
we’re here to help. Call or email us and an experienced customer
support representative will be happy to assist you: [phone]
or support@lifeprofitness.com.
REJUVACURE
FAR INFRARED SAUNA
WELLNESS RECOVERY
4Rejuvacure User Manual Lifepro

6Rejuvacure User Manual Lifepro Wellness Recovery Collection 7
Heater Panel (D)
Front Panel (G)
Oxygen Ionizer (J)
Door Handles (M)
Bench Panel (E)
Cup Holder (K)
Backrest (N)
Roof Cover (I)
Towel Knob (L)
WHAT’S IN THE BOX
3 Bags of Screws
• Six 50mm (Long) Screws
• 4: bench panel; 2: door handles
• Ten 30mm (Medium) Screws
• 4: roof panel; 2: cup holder
• 2: towel knob; 2: extra
• Ten 20mm (Short) Screws
• 8: roof cover; 2: oxygen ionizer
You Will Need (Not Included)
• A standard #2 Phillips head
screwdriver or a drill with a
Phillips head bit.
• A sturdy A-frame ladder or
a step ladder that is at least
five feet tall.
• Two adults for assembly.
Base Panel (A)
Back Panel (B)
Roof Panel (H)
Left Panel (C) Right Panel (F)Left/Right (BACK)

8Rejuvacure User Manual Lifepro Wellness Recovery Collection 9
SIMPLE SAUNA ASSEMBLYGUIDEPARTS OF THE REJUVACURE
Control
Panel
3 Wall
Heaters
Base with
4 Feet
Roof
Panel
Tempered
Glass Door
Outside
Lights (3)
Bench Seat
Bench
Heater
Floor Heater
Vent
WARNING
• Adult assembly is required.
• Keep children away during assembly. This product contains small parts
that may present a choking hazard for children under 3 years old.
• Before assembly, properly dispose of all packaging, especially plastic
bags which may present a suffocation hazard to small children.
• Inspect all heaters for shipping damage before assembly.
• Do not plug the main power cord into an extension cord.
• Do not store flammable items or chemical substances near the sauna.
• Never spray the interior or exterior of the sauna with water or other
liquids.
ASSEMBLY NOTES
• Two adults are required to assemble this sauna.
• Assembly instructions and diagrams include a reference letter, for
example “Gather the back panel (B)”. The reference letters correspond to
the letters identifying each part in WHAT’S IN THE BOX? on pages 6–7.
CHOOSING A LOCATION
When choosing a location for your sauna, please keep in mind the following:
• The sauna must be assembled in a dry, indoor location.
• The sauna must be assembled on a completely level floor.
NOTE: Use a large level to make sure the floor is completely level. If the
floor is not level, you will need to remedy this through shimming or other
method prior to assembling the sauna.
• The main power cord, which exits the roof above the left panel (C), must
be easily accessible.
• The 9-foot main power cord must be able to reach a dedicated electrical
outlet. Do not plug other appliances into the same outlet.
• Leave a few inches of clearance on all sides of the sauna to allow air to
circulate around the sauna.

10 Rejuvacure User Manual Lifepro Wellness Recovery Collection 11
INSTALL THE BACK PANEL
TO THE BASE
CAUTION: Have one adult support the back panel until the left panel is
securely fastened in place.
1. Gather the base panel (A) and the back panel (B).
2. Place the base panel with the floor heater vent facing where you would
like the sauna door to be. See Figure 1.
a. The top of the base panel has a raised molding near each edge. The
wall panels will be placed to the outside of the moldings.
3. Place the bottom edge of the back panel against the raised molding at
the rear of the base panel. See Figure 1.
Figure 1
FRONT
INSTALL THE LEFT PANEL
TO THE BASE
CAUTION: Have one adult support the back panel until the left panel is
securely fastened in place.
1. Gather the left panel (C).
2. Place the left panel on the left side of the base panel (when facing the
sauna from the front). See Figure 2.
3. Fasten the three sets of latches on the back side of the left panel.
a. Lift the lever and fit the round buckle over the tooth on the other
half of the latch.
b. Press the lever down until the small safety catch clicks into place.
2
Figure 2
1
B
Raised
Moldings
Heater
Vent
A
C
Buckle
Tooth
Lever
Safety
Catch

12 Rejuvacure User Manual Lifepro Wellness Recovery Collection 13
INSTALL AND CONNECT THE
HEATER PANEL
1. Gather the heater panel (D).
2. Locate the vertical supports on the left panel. See Figure 3.
3. Hold the heater panel vertically and slide it sideways through the notch
in the floor molding and into the vertical guides on the left panel. See
Figure 3.
a. The power cable on the back of the heater panel will face the back
wall.
b. Be careful not to scratch the floor or the left panel as you slide the
heater panel in place.
4. Plug the heater panel power cable and the heater power cable in the
floor to the two corresponding power cables in the back panel.
3
Figure 3
INSTALL THE BENCH
PANEL
1. Gather the bench panel (E), four 50mm screws, and the Phillips head
screwdriver or drill.
2. Place the bench panel across the top of the heater panel and the
support ledge on the back wall. See Figure 4.
a. The pre-drilled holes in the bench face up.
b. The two pre-drilled holes in the back of the bench are closest to
the edge.
c. Be careful not to scratch the left panel as you place the bench.
3. Use the screwdriver or drill to insert the four 50mm screws to install
the seat. Fully tighten.
4
Figure 4
D
Vertical
Supports
Notch in the
Floor Molding
E

14 Rejuvacure User Manual Lifepro Wellness Recovery Collection 15
INSTALL THE RIGHT AND
FRONT PANELS
1. Gather the right panel (F) and the front panel (G).
2. Place the right panel on right side of the base panel.
a. Make sure the vertical guide on the inside of the right panel lines
up with the right edge of the heater panel.
3. Fasten the three sets of latches on the back side of the right panel.
4. Place the front panel on the front edge of the base panel. See Figure 5.
a. Use caution to avoid damaging or breaking the glass door and
window.
5. Fasten the six sets of latches, three on each side of the front panel.
5
Figure 5
CONNECT THE THREE HEATER
POWER CABLES
NOTE: Have one adult stand on a ladder and hold the weight of the roof
panel in position above the walls while the second adult connects the
heater cables in this step and the control panel cables in the next step.
1. Gather the roof panel (H) and a ladder.
2. Hold the roof panel above the assembled walls of the sauna.
a. The power supply faces up and the roof eave faces front.
3. Locate the heater power cable exiting the top edge of the back, left,
and right panels (one cable each panel). See Figure 6A.
4. Push each cable up through the hole in the roof directly above it and
plug it into the corresponding power cable on the roof. See Figure 6B.
6
Figure 6
G
H
F
FRONT
A
B
Main Power Cable
Air Vent
Power
Supply
Roof
Eave
Heater Cables (3)

16 Rejuvacure User Manual Lifepro Wellness Recovery Collection 17
Figure 7
CONNECT THE CONTROL PANEL CABLES
AND ATTACH THE ROOF
1. Gather four 30mm screws and the Phillips head screwdriver or drill.
2. Locate the two control panel cables exiting the top edge of the front
panel. See Figure 7A.
3. Push the cables up through the hole in the roof and plug them into the
corresponding cables near the power supply. See Figure 7B.
a. Cable connectors are polarized and will only connect one way.
Don't force a connection. See Figure 7C and 7D.
4. Align the corners of the roof panel with the walls and gently push the
roof down into place so that it fits snuggly over the walls.
a. Be careful not to pinch the cables between the roof and walls.
5. Use the screwdriver or drill and four 30mm screws to secure the roof
panel. Fully tighten. See Figure 7E.
INSTALL THE ROOF
COVER
1. Gather the roof cover (I), eight 20mm screws, and the Phillips head
screwdriver or drill.
2. Place the roof cover in position on top of the roof panel. See Figure 8.
a. Make sure the cutout in the roof cover fits around the main power
cable exiting the left side (when facing the sauna from the front).
3. Use the screwdriver or drill to insert the eight 20mm screws to secure
the roof cover. Fully tighten. See Figure 8.
7 8
Figure 8
I
A
BC
D
E
Main Power
Cable

18 Rejuvacure User Manual Lifepro Wellness Recovery Collection 19
Figure 10
INSTALL THE CUP HOLDER
AND TOWEL KNOB
1. Gather the cup holder (K), towel knob (L), four 20mm screws, and the
Phillips head screwdriver or drill.
2. Position the cup holder in the desired location.
3. Use the screwdriver or drill to insert two 20mm screws to secure the
cup holder. See Figure 10.
4. Position the towel knob in the desired location.
WARNING: Do not install the towel knob where towels could touch any
of the wall heaters.
5. Use the screwdriver or drill to insert two 20mm screws to secure the
towel knob. See Figure 10.
10
Figure 9
INSTALL AND CONNECT THE
OXYGEN IONIZER
1. Gather the oxygen ionizer (J), two 20mm screws, and the Phillips head
screwdriver or drill.
2. Locate the oxygen ionizer label in the back-left corner (when facing
the sauna from the front) and the DC power cable entering the sauna
through a hole in the ceiling.
3. Place the oxygen ionizer in position on the wall.
a. The small DC power port on the side of the ionizer will face up.
4. Plug the power cable into the DC port. See Figure 9.
5. Use the screwdriver or drill to insert the 20mm screws to secure the
oxygen ionizer in place. See Figure 9.
a. Be careful not to pinch the power cable when inserting the screws.
9