1. Important safety instructions
This appliance must only be used for space heating. IT IS NOT FOR DOMESTIC USE. Use only in a well-
ventilated area, do not use in Leisure Vehicles such as Caravans, Awnings and Mobile homes, It must not be
used in high-rise flats, basements, bathrooms or bedrooms or as fixed heating. Do not position the
heater close to walls, furniture, curtains, bed linen, or any other inflammable materials where their
positioning may create a fire risk. The unit cannot be used underground.
The unit can only be used with a fixed pressure regulator. The output pressure of the regulator must match
the pressure indicated in the rating label ( 37 mbar ). The rating label can be found on the
heater. The pressure regulator must be approved according to the relevant standards.
The unit can only be used with propane gas.
Check for the presence and proper condition (no damage) of
the seals on the cylinder valve each time the gas
cylinder is changed. Do not use any additional seals.
The Gas cylinder must be protected against heat (for instance, strong direct sunlight).
The heater must only be used with the cylinder in a vertical position.
Make sure the high pressure rubber gas hose is not bent or twisted. The rubber gas hose must be approved
according to the relevant standards.
The flexible hose must be placed in such a manner as to avoid contact with the heated parts of the unit.
Replace the hose as soon as it starts presenting signs of damage or deterioration (inspect regularly).
After assembling the heater, check all connection points for the presence of leaks using a leak detection spray.
Never use a naked flame to perform this leakage test and keep naked flames away when conducting a
leak test. In the event of gas leakage, the appliance MUST be turned off at the gas cylinder
valve. Do not move the unit when it is in operation or hot.
The unit must always be kept under regular supervision during its operation.
Do not touch the outside casing of the unit during or immediately after being used to avoid getting
burnt. The guard on this appliance gets hot when in use, do not touch or remove when using the
heater. Any modification to the heater may be dangerous and is not authorised unless it is made by authorised and
qualified personnel only.
Keep naked flames and ignition sources (such as sparks and others) away during the change of a
cylinder.
Close the cylinder valve fully before changing the cylinder.
When using the greenhouse heater, place it on a flat, stable and non-flammable surface and keep
it at a safe distance from any flammable materials and fabrics. The minimum distances required
are, 40cm for overhead surfaces and 10cm for adjacent side surfaces. The distance for surfaces to the rear is
achieved through the assembled brackets.
When using the greenhouse heater only use the brackets ( feet ) supplied with the unit when assembling and
mounting the heater.
Maintenance and repair should be performed by authorised and qualified personnel only.
Please contact the manufacturer to ask for the technical instructions needed to do the maintenance or repair the
heater. Maintenance or repairs are for authorised and qualified personnel only.
2. Assembling and connecting the heater to the gas cylinder
This appliance must be installed in accordance with the regulations in force.
Before operating the heater, the two supplied brackets (feet) must be mounted on the bottom of the
greenhouse heater with screws supplied (see image A).
Before operating the heater, make sure that the gas connection supply components i.e. type of gas and gas
pressure regulator for this heater are compatible. The regulation values for this unit can be found on
the rating label and in this manual. This unit does not include an exhaust gas evacuation system.
It must be mounted and connected according to the instructions. Pay special attention to the ventilation
requirements.
Attention: After assembling the gas hose to the heater and to the gas regulator, check all connection points for
the presence of gas leakages by using only leak detection spray or a water and soap solution. Never use a
naked flame.
The following items are required to enable the heater to be assembled for use:
-Commercial Gas Cylinder 13kg or 19kg or 47kg;
Pressure regulator fixed 37 mbar (standardized and approved) in accordance with the cylinder with a
minimum amount of
gas flow of 1,0kg/h;
-Hose (standardized and approved) with sufficient length (approx. 80cm);
-Leak detection spray or water with soap;
The greenhouse where you use the appliance must have a minimum volume of 8 CBM. It must have a
section of free flowing ventilation of at least 50 cm2, both in the top and botton parts of the
greenhouse. G)
