Lifetime 90046 User manual

1
Keep this Product ID Number and use when contacting Customer Service:
OWNER’S MANUAL
MODEL N° 90046

2
INSTRUCTION #1062323 E 4/1/2016
Save this owner’s manual for future reference and in the event that
the manufacturer has to be contacted.
REGISTER YOUR PRODUCT ONLINE AT WWW.LIFETIME.COM
At Lifetime, we are committed to providing innovative and quality products. While registering, you will
have the opportunity to give us your feedback. Your input is valuable to us.
Lifetime’s Promise to You:
• You can also opt in to receive new product notifications or promotions.
• In the unlikely event of a product recall or safety modification, your registration provides the
information we need to notify you directly.
• Registration is fast, easy, and completely voluntary.
Maintaining your privacy is our long-standing policy at Lifetime. And you can rest assured that
Lifetime will not sell or provide your personal data to other third parties, or allow them to use your
personal data for their own purposes.
REGISTER today!
We invite you to read our privacy policy at www.lifetime.com
**U.S. and Canada customers ONLY**
DO NOT CONTACT THE STORE!
CALL OUR CUSTOMER SERVICE DEPARTMENT at
1 [phone]
HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time)
**Call, or visit our Web site for Saturday hours**
Questions or Missing Parts? ID:
TO SAVE TIME WHEN CONTACTING CUSTOMER SERVICE, PLEASE HAVE THE PRODUCT ID
AVAILABLE BEFORE YOU CALL; IT’S LOCATED AT THE BOTTOM-LEFT CORNER OF THE FRONT
PAGE OF THIS MANUAL.
**For Assistance in Europe,**
FOR CUSTOMERS OUTSIDE
THE U.S., CANADA, or EUROPE,
PLEASE CONTACT THE STORE
FOR ASSISTANCE.
Please contact:
LIFETIME EUROPE
After Sales, Euro Base
IDA Industrial Estate,
Cork Road Waterford, Ireland
[email protected]
Or call:
00 800 85561360
*One adult required to
complete setup*
This product can be set up by one adult.
Setup is simplified with two adults.

3
PARTS LIST
Parts not shown to scale
PARTS IDENTIFIER
TOOLS REQUIRED
ID Item Description Qty
BZE Adjustable Goal and Net Assembly 1
BZF Storage Straps 2
BZG Net Straps 12*
BZH Stakes 5
BZI Stake Bag 1
NO TOOLS REQUIRED FOR ASSEMBLY
BZE (x1)
Adjustable Goal and Net Assembly
BZH (x5)
Stakes
BZG (x12)*
Net Straps
BZF (x2)
Storage Straps
BZI (x1)
Stake Bag
*Six (6) Net Straps (BZG) come pre-assembled to the Goal & Net Assembly (BZE).
The remaining six (6) Straps are found in the Stake Bag (BZI).

4
Remove the Storage Straps (BZF) from the Adjustable Goal and Net Assembly (BZE).
Step
1.1
Swing the legs out as pictured. Lock the legs into place using the
Locking Pins on the four corner brackets shown.
Step
1.2
BZF
GOAL SETUP
SEC
1
Note: Do not carry the Adjustable Goal and Net Assembly by the Storage Straps.
When folded up, always carry the goal by holding the metal tubing.
!
BZF
BZE
Note: The Net should remain attached to the Assembly. It has been
omitted from these images in order to clarify parts handled during setup.
!
BZE
Locking Pin on
Corner Bracket
Note: If the Locking Pin is difficult to insert, turn the Pin so the ball on the Pin
slips through the hole sideways. Jiggle the tubing while pushing the Pin through
to line up all holes.
!

5
Press in the push buttons on the legs on both sides of the Goal. Extend the
legs by sliding them out until the push buttons snap into the last hole on
the leg.
Step
1.3
Raise the front of the Goal to the highest setting by pressing the push
buttons in and sliding the legs until the push buttons snap into the
highest hole on the leg.
Step
1.4
Push Buttons
Push Buttons
BZE
BZE
BZE
Push Buttons
Note: Make sure one hand is placed on the top tube of the assembly and one
hand placed on the side tube near the push button when performing this step.
!

6
Unfold the back of the Goal and Net Assembly (BZE) until the unit forms a right
angle as pictured. Lock the legs in place using the pins on the two corner
brackets of the Assembly as shown.
Step
1.5
Slide the Stakes (BZH) onto the metal tubes and push the ends into the
ground by hand in the positions indicated.
Step
1.6
Locking Pin on
Corner Bracket
BZE
BZE
Stake

7
At full size, the Soccer Goal will measure 7’ wide and 5’ tall. To adjust
the size to 6’ x 4’, press the push buttons on the top and rear assembly
legs and slide the goal to the middle hole on each tube. Press the
push buttons on the side legs and slide the goal to the middle holes
on each tube.
Step
2.1a
To adjust the size to 4’ x 3’, press the push buttons on the top and rear
assembly legs and slide the goal to the far left hole on each tube. This
will adjust the width. Press the push buttons on the side legs and
slide the goal to the bottom holes on each tube to adjust the height.
Step
2.1b
Bottom Hole
GOAL ADJUSTMENT
SEC
2
Push Buttons
Push Buttons
Middle Hole
Push Buttons
Middle Hole
Push Buttons
Far Left Hole

8
Use four Net Straps (BZG) to tighten the Net. Place the Net Straps on the
metal tubing of the Adjustable Goal and Net Assembly (BZE) in the locations
shown.
Step
2.2
BZE
BZG

9
BZG
Use the remaining two Net Straps (BZG) to gather the excess netting. These
straps will not be placed on the metal tubing, but will gather the net to
itself. The illustration below shows suggested placement points for the Net
Straps.
Step
2.3
Note: To take down the Goal, adjust the assembly to the smallest size before
folding it up.
!

10
NOTES