LIFETONE HLAC100 User manual

PLACETHE LIFETONE HL™ NEXT TO YOUR BED WITH THE SPEAKER FACING THE PILLOW.
Plug in Bed Shaker
Install 4 D Cell
Alkaline Batteries
STEP 1 - POWERING THE HLAC100™
STEP 2 - SMOKE ALARM COMPATIBILITY
5. You may plug the bed shaker in on the back of the clock now
or at any time after it has been set up.
1. Remove the battery door located on the back of your clock.
2. Insert four D cell alkaline batteries, as shown in the illustration at right,
matching the polarity (+ and –) signs in the open compartment.
3. Replace the battery door securely.
4. Plug the Lifetone HLAC100™ into an electrical outlet near your bedside.
NOTE:
The batteries are for backup in the event of a power outage only. The HLAC100 is not meant to operate on batteries alone.
The word “TEST” will now be ashing on the screen. Go to STEP 2.
Smoke alarm has beendetected.
Successful test. You may
now set the clock.
PressTEST/SILENCE
button to silence alarm.
This important test will determine if your smoke alarms are compatible with the Lifetone HL™.
BEEP!
T3 ALARM
SIGNAL
PressTEST/SILENCE
button to start the test.
BED SHAKER
TEST/SILENCE
TEST/SILENCE
BED SHAKER
Doc# LTQSG100 110831
TEST/SILENCE
BED SHAKER
WARNING! DO NOTCOVER
ACPOWER
QUICK START GUIDE – LIFETONE HL™ BEDSIDE FIRE ALARM AND CLOCK MODEL HLAC100
HLAC100 4 D Cell Alkaline
Batteries
Bed Shaker HLAC100 User’s Manual
Thank you for purchasing the Lifetone HL Bedside Fire Alarm and Clock. These items are included:
™
KEEP THIS QUICK-START GUIDE IN A SAFE PLACE
2. When “TEST” starts ashing again, locate the most distant smoke alarm you want detected.
3. Press and hold the test button on the smoke alarm until the Lifetone HL™
alarm sounds. Between 7 and 9 smoke alarm T3 cycles (groups of 3 beeps)
will be required. This takes about 30 to 40 seconds.
4. When the Lifetone HL™ alarm sounds and “F IRE ” appears on the screen,
the test has been successful.
5.To stop the alarm, press the red TEST/SILENCE button on the back of the clock.
6. If all tests are passed,the“12 hr” time display option will ash on the
screen, and you may now set the clock. Go to STEP 3.
NOTE: If the clock is ashing all segments as shown below and beeping at
short intervals, your smoke alarm was not detected or is not compatible with
the LIFETONE HL™.
Unplug the clock and remove one battery. Repeat the set up beginning with
STEP 1- POWERING THE PRODUCT. You may need to choose a closer smoke alarm.
If the compatibility test fails again, the smoke alarm may not be compatible. Unplug
the clock and remove the batteries. See the section titled “UNSUCCESSFUL SMOKE
ALARM COMPATIBILITY TEST” in the user’s manual.
1. The word “TEST” is ashing on the screen. Press the red TEST/SILENCE button on
the back of the clock. The word “TEST” will stop ashing for 30 to 50 seconds.

STEP 3 - SETTING THE CLOCK
NOTE: Any time that you need to reset the clock, press and hold SET CLOCK
until the ashing “12hr” appears, and repeat all parts of STEP 3.
1. On the time display, “12hr” is ashing. To select 24 hour time, press + or – .
2. Press SET CLOCK. The hour will ash. To change the hour, press + or – .
3. Press SET CLOCK. The minute will ash. To change the minute, press + or – .
4. Press SET CLOCK. The year will ash. To change the year, press + or – .
5. Press SET CLOCK. The small “m” and “d” will ash. To change to a day-rst
display of the date, press + or – .
6. Press SET CLOCK. The month will ash. To change the month, press + or – .
8 . Press SET CLOCK. The “E” (for English) will ash. To change
to Spanish or French, press + or – . Press SET CLOCK again.
9. The clock will show the day of the week to the right of the date.
If you prefer to display the year instead, press SET CLOCK again.
STEP 4 - SETTING THE WAKE-UP ALARM
NOTE: Any time that you need to reset the wake-up alarm time, press and hold
SET ALARM until the hour is ashing and repeat all parts of STEP 4.
1. Press and hold SET ALARM until the wake-up hour ashes. To set the hour , press + or – .
2. Press SET ALARM. The minute will ash. To set the minute, press + or – .
You can adjust the volume of your wake-up alarm to high or low with the HI - LO slider
switch on top. If there is a re emergency the alarm will sound at maximum volume.
TROUBLESHOOTING ERROR MESSAGES
PLEASE READTHE USER’S MANUAL COMPLETELYANDTHOROUGHLY FOR
FURTHER DIRECTIONS,PRODUCT FEATURESANDWARRANTY INFORMATION
800 Research Parkway, Suite 339
Oklahoma City, OK 73104
7. Press SET CLOCK. The day will ash. To change the day, press + or – .
3. Press ON/OFF to enable or disable the wake-up alarm. The bell icon at lower
Doc# LTQSG100 110831
For more information,go to www.lifetonesafety.com
or call Customer Service 1-800-648-7923
MODEL HLAC100
Battery ERROR
Bed shaker ERROR
Bed shaker unplugged
BEEP!
BEEP!
Batteries: If the clock is ashing “BATT” and beeping at one minute intervals, the
batteries were not installed, were installed with the wrong polarity, or are below
the required voltage. Remove and insert them again or replace them if necessary.
Be sure to match the polarity (+ and –) signs in the battery compartment. To keep
your compatibility set-up, leave the clock plugged in while you change batteries.
Bedshaker: If the screen is ashing “beds” and the clock beeps, the bed shaker has come
unplugged. Seat the bed shaker plug rmly into the jack on the back of the clock.
NOTE: If you decide you don’t want to use the bed shaker after it has been installed,
unplug the bed shaker then press and hold the red TEST/SILENCE button on the back of
the clock for 2 seconds.That starts a manual self-test that will display“TEST” for 10 to 20
seconds, sound the fire alarm once, and “retrain” the clock to operate without a bed shaker.
Buttons on the top of the Lifetone HL™
left will appear or disappear to indicate whether the alarm is active or inactive.
WAKE-UP TIME
BELL
NOTE: Any time that you want to restore use of the bed shaker, simply plug it in.
HOUR MINUTE
DAYMONTH
MONTH OR
DAY FIRST
YEAR,
LANGUAGE,
DAY OF WEEK
(OR DAY) (OR MONTH)
KEEP THIS QUICK-START GUIDE IN A SAFE PLACE