LIFX SWUS1P2WH Specification sheet

Download the LIFX app
for extra features.

With LIFX Switch you can control both your
LIFX lights and non-smart lights all in one
place either on the wall or in the LIFX app.
The Switch allows you to power on/o
individual lights, Groups of lights, or Scenes
all with the touch of a button as you enter or
leave a room.
Can’t imagine lifting a finger? Set up voice
control and interact with your LIFX Switch
using Google Assistant or Amazon Alexa.
Yo u r S w i t c h .

Dimensions.

Installer instructions.
Important safety notices / avis de sécurité importants
• The LIFX Switch MUST be installed in accordance with local rules and codes.
/ LIFX Switch DOIT être installée conformément aux règles et codes locaux.
• Neutral wire required to the Switch. / Fil neutre requis pour le commutateur.
• Electrical power must be cut obefore installation / repair. / Le courant doit
être coupé avant l’installation / la réparation.
• Do not overload! Total load connected to the switch must be less then 650W.
/ Ne surchargez pas! La charge totale du commutateur ne doit pas excéder
650W.
• Must be protected by 15 amps circuit breaker. An important note to
remember is that circuit breakers can only handle about 80% of their overall
amperage. That means a 15-amp circuit breaker can handle around 12-
amps./ Doit être protégé par un disjoncteur de 15 ampères. Note importante:
les disjoncteurs ne peuvent supporter qu’environ 80% de leur ampérage
global. Un disjoncteur de 15 ampères peut donc supporter environ 12
ampères.
• Make sure to use this product together with 15A circuit breaker in the
upstream. /Assurez-vous d’utiliser ce produit avec un disjoncteur de 15A en
amont.
WARNING - RISK OF OVERHEATING OR FIRE IF THESE LIMITS
ARE EXCEEDED. / AVERTISSEMENT - RISQUE DE SURCHAUFFE
OU D’INCENDIE SI CES LIMITES SONT DÉPASSÉES.

The LIFX Switch is capable of being mounted using most standard stud
brackets, or mounting boxes. With the wall mounting box and electrical
wiring in place, the Switch can be installed.
1. Open the front cover with a
small flat head screwdriver.
2. Connect the wire to the
terminals as needed and
tighten the screws. It is
necessary to connect all
wires to the appropriate
connections. The relay and
buttons will be configured
in the LIFX app once the
Switch is onboarded to the
LIFX app.

4. Reattach the
face plate
securely.
3. Once all wires are securely
connected, ax the Switch
chassis to the mounting
bracket or box using the
supplied screws as shown.
WARNING -DO NOT POWER THE SWITCH FROM THE MAIN CIRCUIT
BOARD BEFORE ATTACHING THE SWITCH CHASSIS TO THE
MOUNTING BRACKET OR BOX.YOU MAY USE THE PROVIDED FACE
PLATE OR ANY STANDARD SINGLE OR MULTI-GANG FACEPLATE./
AVERTISSEMENT -NE PAS ALIMENTER L’INTERRUPTEUR À PARTIR DE
LA CARTE DE CIRCUIT PRINCIPALAVANT D’AVOIR FIXÉ LE CHÂSSIS DE
L’INTERRUPTEUR AU SUPPORT OU À LA BOÎTE DE MONTAGE.VOUS
POUVEZ UTILISER LA PLAQUE FOURNIE OU TOUTE PLAQUE STANDARD.

Once the Switch has been securely attached to the mounting
bracket or box, power the LIFX Switch circuit from the main supply.
Wait 3 seconds. The backlights on the Switch buttons will be faintly
illuminated indicating successful installation. Your LIFX Switch is
now ready for use and configuration using the LIFX app.
General use
The status LED is the small light you see from time to time in the
top left hand corner of the switch when it’s mounted vertically
(portrait alignment). By default you won’t see this light, however
from time it will come on to indicate the Switch is doing something
which is not part of its normal operation. The status LED has the
following codes:
• Green, fast flashing: A Factory Reset is complete and
Switch is now in Setup Mode.
• Green solid: Connected to Cloud.
• Flashing blue: The Switch is in Reboot Mode or performing
an Over-the-Air firmware update.
User instructions.

To Reboot: Hold down the bottom button.
If your Switch is installed horizontally (or landscape) look for the
button furthest away from the status LED light (see image below).
• Flashing orange: Loss of Cloud connectivity
• Flashing red (30 second burst) : Loss of Wi-Fi connectivity.
The light will flash when the following happens: 1) Loss of
Wi-Fi connectivity is first detected, 2) Every 30 mins (for 30
seconds) for the duration of loss of Wi-Fi connectivity, 3)
When a button is pressed during loss of Wi-Fi connectivity.
Flashing lights will typically turn oafter 60 seconds so as not to
become annoying, but will come back on and flash every half
an hour briefly in case nobody has noticed the error. The lights
will also flash if someone presses a button and the Switch is in an
abnormal state.
Common operations.

After 3 seconds the status LED will turn red and there will be a haptic
pulse. Release the button within 2 seconds and the Switch will reboot.
If the button is not released within this period, the Switch will return to
its previous state, i.e. no reboot.
Alternatively and if the Switch is connected to your Wi-Fi, you can use
the LIFX app and go to Device Settings to perform this action.
To Factory Reset
OR First Time
Setup:
Important! The Switch is Factory Reset when Setup Mode is entered.
Please read the next row before proceeding.
Hold down all buttons.
After 10 seconds the status LED will flash green and there will be
a haptic pulse. This is indication that you’ve entered Setup Mode.
Now it’s time to Onboard your Switch to your Wi-Fi. Do so by doing
the following:
• Release the buttons and the Switch.The status LED will now flash
green to indicate it is discoverable.
• Open the app and select “Add New Device” and follow the
prompts to connect to the Wi-Fi network.
• Once the Switch has connected to the LIFX cloud, the status LED
will change to green and then turn oafter 60 secs.
If you’ve entered
Setup mode and
want to exit:
Continue holding all buttons down beyond the 10 second point
After 15 seconds the following will happen:
• Status LED will turn o
• Setup mode will be cancelled
To exit Setup
Mode:
Once in Setup Mode, press down all Switch buttons for 3 seconds.
The Switch will be Factory Reset and no longer be discoverable once
this is done.
Factory Reset
(alternative):
If the Switch is connected to a Wi-Fi network and is shown in the LIFX
app you can reset it from the Device Settings screen.

Part No.: SWUS1P2WH
SWUS1P2BL
Type: 1 Gang
Rated Input
Voltage:
120VAC
Frequency: 60HZ
Maximum Load: 650W Incandescent
210W LED