Ubiquiti ES-24-250W User manual

18/10/21, 15:20
ES-24-250W, ES-24-500W Quick Start Guide
https://dl.ui.com/qsg/ES-24-250W_ES-24-500W/ES-24-250W_ES-24-500W_EN.html
1/14
EdgeSwitch Mounting Screws (Qty. 4) Cage Nuts (Qty. 4)
Power Cord
Package Contents
Installation Requirements
Phillips screwdriver
Standard-sized, 19" wide rack with a minimum of 1U height available
For indoor applications, use Category 5 (or above) UTP cabling approved for
indoor use.
For outdoor applications, shielded Category 5 (or above) cabling should be
used for all wired Ethernet connections and should be grounded through the
AC ground of the power supply.
We recommend that you protect your networks from harmful outdoor
environments and destructive ESD events with industrial-grade, shielded
Ethernet cable from Ubiquiti. For more details, visit: ui.com/toughcable
Note: Although the cabling can be located outdoors, the EdgeSwitch
itself should be housed inside a protective enclosure.
Hardware Overview
ES-24-250W, ES-24-500W Quick Start Guide

18/10/21, 15:20
ES-24-250W, ES-24-500W Quick Start Guide
https://dl.ui.com/qsg/ES-24-250W_ES-24-500W/ES-24-250W_ES-24-500W_EN.html
2/14
System LED
RJ45 PoE LED (Ports 1 - 24)
RJ45 Speed/Link/Activity LED (Ports 1 - 24)
Note: The System LED functionality has been updated with firmware
v1.8.0. We recommend that you update the EdgeSwitch to the latest
firmware.
Flashing White Bootup in progress.
White
Ready for use, not connected to Ubiquiti®
Network Management System (UNMS™). See
“UNMS Management”.
Blue Ready for use, connected to UNMS.
Steady Blue with
Occasional Flashing
Ready for use, unable to connect to UNMS, check
connection to UNMS server.
Quickly Flashing Blue Used to locate a device in UNMS.
Alternating
Blue/White Firmware upgrade in progress.
Off No PoE
Amber IEEE 802.3af/802.3at
Green 24V Passive
ES-24-250W, ES-24-500W Quick Start Guide

18/10/21, 15:20
ES-24-250W, ES-24-500W Quick Start Guide
https://dl.ui.com/qsg/ES-24-250W_ES-24-500W/ES-24-250W_ES-24-500W_EN.html
3/14
SFP Speed/Link/Activity LED (Ports 1 - 2)
RJ45 (Ports 1 - 24)
SFP (Ports 1 - 2)
Reset Button
Console Port
Power Port
Off No Link
Amber
Link Established at 10/100 Mbps
Flashing Indicates Activity
Green
Link Established at 1000 Mbps (1 Gbps)
Flashing Indicates Activity
Off No Link
Green
Link Established at 1 Gbps
Flashing Indicates Activity
RJ45 ports support Power over Ethernet (PoE) and 10/100/1000 Ethernet
connections.
Hot-swappable SFP ports support 1 Gbps connections.
Click here to learn how to reset an EdgeSwitch to factory defaults.
RJ45 serial console port for Command Line Interface (CLI) management.
Connect the included Power Cord to the Power port.
Hardware Installation
1.
ES-24-250W, ES-24-500W Quick Start Guide

18/10/21, 15:20
ES-24-250W, ES-24-500W Quick Start Guide
https://dl.ui.com/qsg/ES-24-250W_ES-24-500W/ES-24-250W_ES-24-500W_EN.html
4/14
2.
OR
ES-24-250W, ES-24-500W Quick Start Guide

18/10/21, 15:20
ES-24-250W, ES-24-500W Quick Start Guide
https://dl.ui.com/qsg/ES-24-250W_ES-24-500W/ES-24-250W_ES-24-500W_EN.html
5/14
3.
ES-24-250W, ES-24-500W Quick Start Guide

18/10/21, 15:20
ES-24-250W, ES-24-500W Quick Start Guide
https://dl.ui.com/qsg/ES-24-250W_ES-24-500W/ES-24-250W_ES-24-500W_EN.html
6/14
Connecting Ethernet
Note: The PoE settings for ports 1-24 are set to PoE+ auto by default, so
802.3af/at devices can be plugged in and automatically receive PoE. For
instructions on how to enable 24V passive PoE, refer to “Configuring PoE
Settings”.
Connecting SFP
1.
2.
ES-24-250W, ES-24-500W Quick Start Guide

18/10/21, 15:20
ES-24-250W, ES-24-500W Quick Start Guide
https://dl.ui.com/qsg/ES-24-250W_ES-24-500W/ES-24-250W_ES-24-500W_EN.html
7/14
3.
For information about compatible fiber SFP modules, visit:
ubnt.link/SFP_DAC_Compatibility
Accessing the Configuration Interface
The EdgeSwitch is set to DHCP by default, so it will try to automatically obtain an
IP address. If that fails, then it will use the default fallback IP address,
192.168.1.2. Proceed to the appropriate section, DHCP or “Fallback IP Address”:
DHCP
Use one of the following methods:
ES-24-250W, ES-24-500W Quick Start Guide

18/10/21, 15:20
ES-24-250W, ES-24-500W Quick Start Guide
https://dl.ui.com/qsg/ES-24-250W_ES-24-500W/ES-24-250W_ES-24-500W_EN.html
8/14
Set up the DHCP server to provide a specific IP address to the EdgeSwitch
based on its MAC address (on the label).
Let the EdgeSwitch obtain an IP address and then check the DHCP server to
see which IP address was assigned.
To log in, follow these steps:
1. Launch your web browser. Type the appropriate IP address in the address
field. Press enter (PC) or return (Mac).
2. Enter ubnt in the Username and Password fields. Click Sign In.
3. The EdgeSwitch Configuration Interface will appear. Customize additional
settings as needed.
For more information on PoE configuration, refer to “Configuring PoE Settings”.
For more information, refer to the EdgeSwitch documentation, which is available
at ui.com/download/edgemax
Fallback IP Address
1. Ensure that your computer (or other host machine) is connected to the
EdgeSwitch.
ES-24-250W, ES-24-500W Quick Start Guide

18/10/21, 15:20
ES-24-250W, ES-24-500W Quick Start Guide
https://dl.ui.com/qsg/ES-24-250W_ES-24-500W/ES-24-250W_ES-24-500W_EN.html
9/14
2. Configure the Ethernet adapter on your host system with a static IP address on
the 192.168.1.x subnet.
3. Launch your web browser. Type the appropriate IP address in the address field
(192.168.1.2 is the default fallback IP address). Press enter (PC) or return
(Mac).
4. Enter ubnt in the Username and Password fields. Click Sign In.
5. The EdgeSwitch Configuration Interface will appear. Go to Settings .
6. Change the IP Address to a unique IP address. Click Apply.
ES-24-250W, ES-24-500W Quick Start Guide

18/10/21, 15:20
ES-24-250W, ES-24-500W Quick Start Guide
https://dl.ui.com/qsg/ES-24-250W_ES-24-500W/ES-24-250W_ES-24-500W_EN.html
10/14
Note: If you change the IP settings, then the session will be cut off, and
you will need to reconnect to the EdgeSwitch using the new IP address.
Customize additional settings as needed. For more information on PoE
configuration, refer to “Configuring PoE Settings”.
UNMS Management
You can manage your device using UNMS, which lets you configure, monitor,
upgrade, and back up your devices using a single application. Get started at
www.unms.com
Configuring PoE Settings
The PoE settings for ports 1-24 are set to PoE+ by default, so 802.3af/at devices
can be plugged in and automatically receive PoE.
WARNING: Before activating 24V passive PoE, ensure that the connected
device supports PoE and the supplied voltage.
1. Go to Dashboard .
2. For the Ethernet port you want to configure, click the PoE drop-down menu.
ES-24-250W, ES-24-500W Quick Start Guide