Light Bright Synjax Zoom 40 User manual

Synjax Zoom 40
LED Washlight
User Manual
V 1.0!

Light Bright
Synjax Zoom 40
Contents
1. Introduction 3
2. Safety instructions 4
3. Unpacking the device 6
4. Installation 6
5. DMX-Connection 7
6. Mounting the device 8
7. Control Panel 8
8. Channel assignment 11
9. Photometric data 16
10. Technical details 17
11. Service and cleaning 18
12. Notes 19
2

Light Bright
Synjax Zoom 40
1. Introduction
ATTENTION: For your own safety, please read these operating
instructions carefully before the first use.
The headlight has left our company in best condition. To maintain this condition and to ensure
safe operation, it is absolutely necessary to observe the following safety instructions and
warnings, which are described in this operating manual.
The manufacturer does not accept any liability for damage caused by not following these
operating instructions or unauthorized changes to the device.
Please note that damage caused by manual changes to this device is not covered by the
warranty.
ATTENTION: This device is for professional use only! Protection class IP
20 - only for use in dry environment (indoor)!
Light Bright does not authorize the use of your devices in life support
systems. Life Support Systems are systems whose purpose is to
maintain or stabilize life and whose defect or malfunction could result in
death or injury to persons.
3

Light Bright
Synjax Zoom 40
2. Safety instructions
CAUTION: Disconnect the device from the power supply before opening
the device. Touching live parts can cause an electric shock.
Make sure that the mains voltage to be connected is not higher than the voltage indicated on
the type plate. This device should only be operated with the power source specified on the
type plate.
If you are not sure what type of power supply you have, contact your dealer or your power
company.
Always disconnect the device from the power supply before carrying out cleaning work,
changing fuses or replacing parts.
The power plug must always be accessible after the installation of the spotlight. Do not
overload the sockets or extension cords as this may result in fire or electric shock. Do not
place any objects on the power cord. Do not install the spotlight in such a way that people
can trip over the power cord or step on it. Make sure that the power cord can never be
crushed or damaged by sharp edges. Check the unit and the power cord from time to time.
Always leave maintenance work to a qualified technician.
ATTENTION: This light corresponds to protection class I. Therefore this
light must be connected to a mains socket with earthing contact.
Never connect this device to a dimmable power source.
Some smoke and odor may be produced during initial operation. This is a normal procedure
and does not necessarily mean that the unit is defective.
The device becomes hot during operation. Never touch the device with bare hands during
operation!
When replacing fuses, only use fuses of the same type with identical values. Have fuses
replaced only by a qualified technician.
4

Light Bright
Synjax Zoom 40
ATTENTION: EYE DAMAGE! Do not look into the light source for a long
time during operation. This can be harmful to the eyes. Possibly
dangerous radiation.
If the device was exposed to strong temperature fluctuations (e.g. after transport), the device
must not be switched on immediately. The resulting condensation water can damage your
device. Leave the device switched off until it has reached room temperature.
Do not shake or knock the device. Avoid brute force during installation or operation.
This spotlight was designed for indoor use only. Do not expose this unit to rain or moisture.
When choosing a mounting location, make sure that the device is not exposed to extreme
heat, humidity or dust.
Ventilation openings and slits in the head and foot of the headlamp serve for ventilation. To
ensure reliable operation of the device and to protect it from overheating, these openings
must not be covered.
Never cover the front lens when the headlight is in operation.
The openings should never be covered with fabrics or other objects, so that the airways are
blocked.
This unit must not be operated in an environment without adequate ventilation.
The device may only be operated when the housing is closed and all screws / snap
connectors are firmly tightened.
The device must always be secured with an additional safety device.
Make sure that the area underneath the spotlight is clear during installation, conversion and
dismantling.
ATTENTION: The distance between the light emission and the
illuminated surface must be at least 2.0 meters.
The front lens must be replaced if it is visibly damaged so that its
function is impaired, e.g. by cracks or deep scratches!
To avoid damaging the internal parts of the lamp base, never let sunlight
shine directly into the front lens.
The maximum ambient temperature of 45°C must not be exceeded.
5

Light Bright
Synjax Zoom 40
Do not operate the device until you have familiarized yourself with its functions. Prevent
operation by persons who are not qualified to use the device. Most damage is the result of
improper operation!
Please use the original packaging or specially adapted flight cases when transporting the
device.
3. Unpacking the device
Contents of the package: The headlight, a Powercon connection cable and Omega brackets
for mounting.
Open the packaging carefully on the top side and check the headlight and accessories for
possible transport damages. These should be reported immediately to the transport
company.
4. Installation
The device comes with a ready made-up Powercon connection cable. Please use only the
supplied cable or a cable of the same type assembled by a specialist. The connection of the
device to the power supply must also be carried out by an authorized specialist.
Connection in Germany/Europe:
Connected loads: voltage 100-240 V, frequency 50 - 60 Hz, power max. 520W, 2.1A
The electrical safety as well as the function of the device is only guaranteed if it is connected
to a properly installed protective conductor system. It is very important that this basic safety
requirement is present. In case of doubt, have the electrical installation checked by a
specialist. The manufacturer cannot be held responsible for damage caused by a missing or
interrupted protective conductor (e.g. electric shock)! Only use the device in a completely
assembled state so that no electrical components can be touched. (danger 100-240 V)
If you have observed the listed points, you can plug in the devices or have them connected to
the mains by a specialist.
Conductor color
Function
Symbol
Brown
Phase
„L“
Blue
Neutral conductor
„N"
Yellow/green
Protective earth
„PE“ ⏚
6

Light Bright
Synjax Zoom 40
ATTENTION: The spotlight may light up immediately if standalone
operation is activated or a DMX signal is applied!
5. DMX-Connection
The DMX cabling (signal lines) should be done with a 2-wire cable with shielding. We
recommend a DMX cable with 110 Ohm, 2x0,22mm2or 4x0,22mm2. The plugs and sockets
are 3-pin XLR-connectors, which can be purchased in specialized shops.
Pin assignment:
Pin1 = Ground / Shielding
Pin2 = DMX -
Pin3 = DMX +
The spotlight has a DMX-in and DMX-out connection. Now connect the DMX output of your
controller to the first spotlight (Controller DMX-Out -> Spotlight DMX-In). Then connect the
first spotlight with the second spotlight and so on. In some cases it is advisable to plug in a
so called end plug/end resistor (XLR plug with a resistor of 120 Ohm between pin 2 and pin
3). Whether or not an end plug is required depends on various factors, including the cable
lengths used and the number of units. However, as long as there are no problems in the DMX
line, it is not necessary.
7

Light Bright
Synjax Zoom 40
6. Mounting the device
Warning: There must be a 0.5m safety distance between the light source
and flammable material and a minimum distance of 2.0m between the
light source and the surface to be illuminated.
The spotlight can either be positioned or suspended from a truss system. Horizontal
mounting to the truss is also permitted.
If you place the unit on the floor, you may only operate the unit on a hard surface, as the air
inlets in the foot must remain free!
To hang the unit on a truss system, use the supplied Omega clamps with snap-connectors.
Make sure that the snap connectors engage securely. Make sure that the truss system to
which you attach the device complies with safety regulations. If you use a truss, always
secure the headlight with a safety device that complies with national regulations. Use the
safety eyelet on the device.
7. Control Panel
The spotlight has a display to show the set parameters and four buttons to adjust them. In
addition, the Arnold460 has a "WirelessIndicator" LED, which indicates the current DMX
signal reception.
8

Light Bright
Synjax Zoom 40
1. DMX-ADRESS
!Here you can set the DMX-address of the device. Use the "Up" and "Down" keys to the
desired DMX address and confirm with "Ok".
2. MODE
!Here you can switch the Mode for the Synjax Zoom40
3. TEST
4. RESET
9
According to the current channel, all functions of the Synjax Zoom 40 can be tested
manually here.
2.1 Backlight time
Einstellen wie lange das Gerät den DMX Hold beibehält. Auswahl zwischen 15s;30s;60s
oder konstant.
2.2 Language
Switching the Menu - language
2.3 Reset
For Failures you can reset the device here.
2.4 Calibration
You can switch the password here.
Unlike in the Set Up menu, different parameters can be reset under this menu item:
4.1 Focus reset
Resets the zoom motor.
4.2 Pan/Tilt reset
Resets the pan/tilt motors.
4.3 Reset all
Resets all motors of the device.

Light Bright
Synjax Zoom 40
5. INFORMATION
!
10
5.2 Error Messages
Displays the past and current error messages of the device.
5.3 DMX Data monitoring
Displays the current DMX information.
5.4 Software Info
Displays the currently installed version of the software.

Light Bright
Synjax Zoom 40
8. Channel assignment
20Ch
68Ch
Value
Funktion
1
1
Pan (8bit)
0-255
Pan movement
2
2
Tilt (8bit
0-255
Tilt movement
3
3
Dimmer
0-255
Dimmer 0-100%
4
4
Strobe
0-3
No function
4-255
Strobe Effect slow-fast
5
5
Color red
0-255
Red 0-100%
6
6
Color green
0-255
Grün 0-100%
7
7
Color blue
0-255
Blue 0-100%
8
8
Color white
0-255
White 0-100%
9
9
Focus
0-255
0% - 100% linear focus
10
10
Static effects
0-3
No function
4-7
Coloreffect 1
…
…
96-99
Coloreffect 24
100-103
Non-gradable effect 1
…
…
252-255
Non-gradable effect 39
11
11
Dynamic effects
0-3
No function
4-7
Color effect 1
…
…
96-99
Color effect 24
20Ch
68Ch
11

Light Bright
Synjax Zoom 40
100-103
Non-gradable effect 1
…
…
252-255
Non-gradable effect 39
12
12
Effect speed
0-63
Effect static
64-158
Forward from fast to slow
159-255
Backwards from slow to fast
13
13
Backlight red
0-255
Red 0-100%
14
14
Backlight green
0-255
Green 0-100%
15
15
Backlight blue
0-255
Blue 0-100%
16
16
Backlight White
0-255
White 0-100%
17
17
Pan fine (16bit)
0-255
Pan movement fine
18
18
Tilt fine (16bit)
0-255
Tilt movement fine
19
19
Pan/Tilt Speed
0-255
Pan/Tilt speed control
Value
Funktion
20Ch
68Ch
20Ch
68Ch
Value
Funktion
20
20
Reset
0-229
No function
230-235
Reset Pan/Tilt, reset console (hold for 3sec.)
236-239
No function
240-245
Reset focus (hold 3 sec.)
246-250
No function
252-255
Reset all (Hold 3 sec.)
Single pixel control
21
Red 1
0-255
Red 0-100%
20Ch
68Ch
12

Light Bright
Synjax Zoom 40
22
Green 1
0-255
Green 0-100%
23
Blue 1
0-255
Blue 0-100%
24
White 1
0-255
White 0-100%
25
Red 2
0-255
Red 0-100%
26
Green 2
0-255
Green 0-100%
27
Blue 2
0-255
Blue 0-100%
28
White 2
0-255
White 0-100%
29
Red 3
0-255
Red 0-100%
30
Green 3
0-255
Green 0-100%
31
Blue 3
0-255
Blue 0-100%
32
White 3
0-255
White 0-100%
Value
Funktion
20Ch
68Ch
20Ch
68Ch
Value
Funktion
33
Red 4
0-255
Red 0-100%
34
Green 4
0-255
Green 0-100%
35
Blue 4
13

Light Bright
Synjax Zoom 40
35
0-255
Blue 0-100%
36
White 4
0-255
White 0-100%
37
Red 5
0-255
Red 0-100%
38
Green 5
0-255
Green 0-100%
39
Blue 5
0-255
Blue 0-100%
40
White 5
0-255
White 0-100%
41
Red 6
0-255
Red 0-100%
42
Green 6
0-255
Green 0-100%
43
Blue 6
0-255
Blue 0-100%
44
White 6
0-255
White 0-100%
45
Red 7
0-255
Red 0-100%
46
Green 7
0-255
Green 0-100%
47
Blue 7
0-255
Blue 0-100%
48
White 7
0-255
White 0-100%
49
Red 8
20Ch
68Ch
Value
Funktion
14

Light Bright
Synjax Zoom 40
49
0-255
Red 0-100%
50
Grün 8
0-255
Green 0-100%
51
Blue 8
0-255
Blue 0-100%
52
White 8
0-255
White 0-100%
53
Red 9
0-255
Red 0-100%
54
Green 9
0-255
Green 0-100%
55
Blue 9
0-255
Blue 0-100%
56
White 9
0-255
White 0-100%
57
Red 10
0-255
Red 0-100%
58
Green 10
0-255
Green 0-100%
59
Blue 10
0-255
Blue 0-100%
60
White 10
0-255
White 0-100%
61
Red 11
0-255
Red 0-100%
62
Green 11
0-255
Green 0-100%
Blue 11
20Ch
68Ch
Value
Funktion
15

Light Bright
Synjax Zoom 40
9. Photometric data
63
0-255
Blue 0-100%
64
White 11
0-255
White 0-100%
65
Red 12
0-255
Red 0-100%
66
Green 12
0-255
Green 0-100%
67
Blue 12
0-255
Blue 0-100%
68
White 12
0-255
White 0-100%
20Ch
68Ch
Value
Funktion
Radiation
angle distance
Lux
9°
5m
24600
40°
5m
1577
16

Light Bright
Synjax Zoom 40
10. Technical details
•Light source: 12x40 RGBW multichip LEDs !
!
•Power supply: AC100-240V 50/60Hz with switch switch!
•PowerCon In/out!
•Inrush current approx. 520W!
•
•Pan from 540° (16bit)!
•Tilt from 270° (16bit)!
•
•DMX 20 and 68 channel!
•Motorized Focus!
•Single pixel control!
•Lineares Dimmen von 0-100%!
•CMY Mixing!
•Linear zoom from 8° - 60!
•Pan/Tilt adjustment manual!
•RDM capable!
•Dimensions: 380 x 465 x 280mm!
•Weight: 15kg!
!
17

Light Bright
Synjax Zoom 40
11. Service and cleaning
WARNING: Disconnect the device from the power supply before opening
it!
You should check the function of the fans in the head and base at regular intervals. Above all,
you should make sure that the air inlets and the inside of the headlight are free of lint and
dust.
To do this, open the head cover and the base plate at the foot. You can clean the headlight
with a brush/cleaning cloth and a vacuum cleaner or compressor (only at low speed).
Make sure that you do not bend or damage any parts during cleaning. After cleaning is
complete, close all covers again with the associated screws and perform a function test.
Please use only lint-free, clean cleaning cloths or brushes and cleaning agents without
alcohol to clean your device. We recommend regular cleaning at least every three months.
Look for damage to the device, parts of the device and connection cables. If you notice any
damage, DO NOT use the device and take it to an authorized dealer to eliminate any danger
from using defective equipment and to have your device professionally repaired.
18

Light Bright
Synjax Zoom 40
12. Notes
This device complies with the CE directive:
•within the meaning of Directive: 2014/35/EU Low Voltage
Directive, (Directive 2014/35/EU of the European Parliament and
of the Council of 26.02.2014 on the harmonization of the laws of
Member States relating to electrical equipment designed for use within certain
voltage limits).
•within the meaning of Directive: 2014/30/EU Electromagnetic Compatibility
(Directive 2014/30/EU of the European Parliament and of the Council of
26.02.2014 on the approximation of the laws of the Member States relating to
electromagnetic compatibility).
The device complies with IP20 and is thus protected against the ingress of solid foreign
bodies with a diameter greater than 12mm (first code number 2), while it is sensitive to
humidity, splashing and jetting water.
During operation, it is obligatory to connect the device to a power supply system equipped
with an efficient grounding (class 1 device according to EN 60598-1 directive). Furthermore, it
is recommended to protect the supply line of the devices against indirect contact and/or
short circuits with correctly rated residual current circuit breakers.
Use the device only when the room temperature is below 45°C.
Before starting maintenance on the device, it must cool down for at least 10 minutes after
disconnection from the power supply in order to minimize the risk of damage to the chips.
For maintenance work or repairs to the chips, the device must cool down for at least another
20 minutes to prevent burning.
19