Hybrid+ HSS COB4B User manual

User Manual
Please read the instructions carefully before use

1A
TABLE OF CONTENTS
1. Safety Instructions
2. Technical Specifications
3. Installation
4. How to set up the unit
5. How to control the fixture
6. DMX512 Configuration
7. DMX512 Connections
8. Troubleshooting
9. Fixture Cleaning

2A
1. Safety Instructions
WARNING
Please keep this User Manual for future consultation. If you sell the fixture to another
user, be sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the fixture.
Before operating, ensure that the voltage and frequency of the power supply match the
power requirements of the fixture.
It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
Disconnect main power before servicing and maintenance.
Use safety chain when fixing this fixture. Don’t handle the fixture by taking its head only,
but always by taking its base.
Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature is
higher than this.
In the event of a serious operating problem, stop using the fixture immediately. Never
try to repair the fixture by yourself. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center. Always use the same type of spare parts.
Do not connect the device to any dimmer pack.
Do not touch any wire during operation as there might be a hazard of electric shock.
To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain
or moisture.
The housing must be replaced if there is visible damaged.
Do not look directly at the LED light beam while the fixture is on.
Caution
There are no user serviceable parts inside the fixture. Do not open the housing or attempt
any repairs yourself. In the unlikely situation your unit may require service, please contact
your nearest dealer.
Please read the instructions carefully which include important
information about the installation, operation and maintenance.

3A
2. Technical Specifications
● DMX modes: 12 channels
● 4 push button with 4 Digital LED Display
● Auto, Sound Actived,DMX512,Master/Slave
● Power Supply:AC90V-250V/50-60Hz
● Power Consumption:410W
● Light source: 4pcs 100 Watt Cool White +Warm White Ultra Bright LEDs
● LED life: 5-6 million hours
● Packing Size: L410×W410×H275 mm
● Net Weight : 8.3kg
3. Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is
firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure
to which you are attaching the unit is secure and is able to support a weight of 10 times the
unit’s weight. Also always use a safety cable that can hold 12 times the weight of the unit
when installing the fixture.
The equipment must be fixed by professionals. It must be fixed at a place where it is out of
the reach.
4. How To Set Up The Unit
4.1 Control Panel

4A
Button:
MENU
To select the programming functions
UP
To go forward in the selected functions
DOWN
To go backward in the selected functions
ENTER
To confirm the selected functions
4.2 Main Function
d001
001-512
DMX Address
Auxx
01
Cool White
02
Warm White
03
Full on
04
Jump change mode 1
05
Jump change mode 2
06
Gradual change mode
So01
Sound-Jump change
So02
Sound-Gradual change
St00
St00-St16
Strobe speed from slow to fast
SP00
SP01-SP16
Au04/05/06 Speed from slow to fast
cu00
000-255
Cool White dimmer
uu00
000-255
Warm White dimmer
5. How to control the fixture
There are three ways to control the fixture
A. Universal DMX controller
B. Master/Slave operation
A. Universal DMX controller
The fixture can be set to the DMX address remotely by the universal DMX controller. First,
you need to program two scenes into a chase, then link the fixtures to the universal DMX
controller. When you run the chase, all the fixtures of the chain will be set to the series DMX
address automatically. The fixture uses four channels. Please refer to the following table to

5A
set the address for the first four units.
Channels mode
Unit1
Address
Unit2
Address
Unit3
Address
Unit4
Address
CH12
1
13
25
37
B. Master/Slave operation
The fixture will allow you to link 16 fixtures together and operate without a controller. In
Master/Slave mode, the first fixture will control the others to give an automatic, sound
activated, synchronized light show. This function is good when you want an instant show.
The first fixture’s DMX input cable will have nothing connect it, and the other fixtures will be
set in slave mode automatically. Their DMX input cables connect the last fixture DMX output
cable (daisy chain). Any fixture can act as a Master or as a Slave
6. DMX512 Configuration
12 channel Mode:
Channel
Value
Function
CH1
0-255
Master dimmer
CH2
0-255
Strobe mode
CH3
0-200
Auto mode
201-255
Sound mode
CH4
0-255
Auto speed
CH5
0-255
1 Cool White dimmer
CH6
0-255
1 Warm White dimmer
CH7
0-255
2 Cool White dimmer
CH8
0-255
2 Warm White dimmer
CH9
0-255
3 Cool White dimmer
CH10
0-255
3 Warm White dimmer
CH11
0-255
4 Cool White dimmer
CH12
0-255
4 Warm White dimmer

6A
7. DMX512 Connections
The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.
1. If you are using a controller with a 5 pin DMX output, you need to use a 5 to 3
pin adapter-cable.
2. Connect the fixture together in a “daisy chain” plug XLR cable from the output of
the fixture to the input of the next fixture. The cable cannot be branched or split
to a “Y” cable. Inadequate or damaged cables, soldered joints or corroded
connectors can easily distort the signal and shut down the system
3. The DMX output and input connectors are pass-through to maintain the DMX
circuit when one of the units’ power is disconnected.
4. At last fixture, the DMX cable has to be terminated with a terminator to reduce
signal errors. Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and pin
3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.
5. Each lighting fixture needs to have an address set to receive the data sent by
the controller. The address number is between 0-511 (usually 0 & 1 are equal to
1).
6. 3 pin XLR connectors are more popular than 5 pin XLR.
3 pin XLR: Pin1: GND, Pin2: Negative signal (-), Pin3: Positive signal (+)
5 pin XLR: Pin1: GND, Pin2: Negative signal (-), Pin3: Positive signal (+)
Pin4/5: Not Used.
8. Troubleshooting
The following are a few common problems that may occur during operation. Here are some

7A
suggestions for easy troubleshooting:
A. The fixture does not work, It has no light
1. Check the connection of power and main fuse.
2. Measure the main power supplys voltage on the main connector.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if they are linked
properly.
2. If the DMX LED is on and there is no response to the channel, check the address
settings and DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on the connectors or on
PCB of the fixture or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside high voltage cables that may cause
damage or interference to DMX interface circuit.
C. Some fixtures don’t respond to the easy controller
1. You may have a break in the DMX cabling. Check the LED for the response of the
master/ slave mode signal.
2. Wrong DMX address in the fixture. Set the proper address.
D. No response to the sound
1. Make sure the fixture does not receive DMX signal.
2. Check microphone by tapping the microphone.
9. Fixture Cleaning
Internal cleaning must be carried out periodically to optimize light output. Cleaning
frequency depends on the environment in which the fixture operates: damp, smoky or
particularly dirty surroundings can cause greater accumulation of dirt on the fixture’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.