Light Efficient Design RemPhos RP-SPT-20W-40K-SF-G1 User manual

Off Grid LED Solar Post Top
User Manual
20W / 2000 LM
Created: 4/16/2019

Product Model
RP-SPT-20W-40K-SF-G1
Power/ Lumen
20W / 2000 LM
Dimension
16.38 in * 32.68 in
LEDS
80pcs LEDs
Li-Ion Battery
88.8WH, 14.8V
Solar Panel
12.5W Polycrystalline
Working Mode
Selectable Mode 1 and Mode 2
Detection Angle/ Area
24ft
Material
Aluminum Alloy + Polycarbonate
Charge Time
Around 8-10 hours of sunlight
Beam Angle
360°
IP Degree
IP65
Recommended Install Height
8-12 ft
Mounting Pole Dimensions
MIN 3 in MAX 3.5 in
Warranty
3 YEARS
Packing
QTY/CTN: 1pc
Battery Charing Temp
Charging Temperature 32°F ~ 149°F
Discharging Temperature -4°F ~ 149°F
Fixture Operating Temp
-4°F ~ 149°F
How to Install the Solar Post Top
Easy to install, just use the supplied screws to fix
the light to the pole.
The fixture will fit poles between 3 in –3.5 inches
Warning:
1. No one should attempt to disassemble the light.
2. It is strictly prohibited to disassemble the
battery for personal use.
3. If the lamp doesn’t receive any charge for 3-5
days, the battery may be low or out of power,
make sure that it receives enough sun during
the day and that there isn’t anything blocking
the sun’s rays going to the panel.
Special Note:
1. Do not install the lamp where no sunlight is available
otherwise the lamp will have a hard time absorbing
light. Do not install the lamp under a shadow or
between two buildings.
2. Do not use the lamp in an environment with a
temperature above 149 F° or below -4 F°, otherwise it
will cause rapid attenuation of the battery and affect the
batteries longevity or even damage.
3. Choose the operating mode based on your local
sunshine and lighting needs.
4. In order to ensure that the lamp works in an ideal state
over time, clean the solar panel lens every few months
to clear dust and debris.
1. Decoration Piece
2. Solar Panel
3. Lamp
4. PIR Sensor
5. Solar Panel Lens Cover
6. Switch

Phase 1: The light will be off during
daytime charging.
Mode 1: Phase 2: The light will auto
turn on to 700LM (35%) for the first 5
hours at night.
Mode 2: Phase 2: The light will auto
turn on to 600LM (30%) for the first 5
hours at night.
Mode 1: Phase 3: After 5 hours of
bright light, the lamp will then turn
down to 200LM (10%) until dawn.
The Red Light Indicates that the lamp is running
on Mode 1: 5 hours at 35% (700LM) brightness
followed by 7 hours at 10% (200LM) brightness
until dawn. (During the entire night the lamp will
turn up to 100% (2000 LM) for 30 seconds when
motion is sensed.
How the Light Operates
Example of Modes 1 & 2
The Green Light Indicates that the lamp is
running on Mode 2: 5 hours at 30% brightness
followed by 5 hours at 10% brightness and then
2 hours at 20% brightness until dawn (During the
entire night the lamp will turn up to 100% (2000
LM) for 30 seconds when people are present.
Instructions
Turn on the lamp: Press the button down for 3
seconds to switch on/off.
Press the button quickly to choose the lighting
Mode 1 & 2. Red Indicator for Mode 1 & Green
Indicator for Mode 2.
Mode 2: Phase 3: After 5 hours of
bright light, the lamp will then turn
down to 200LM (10%) for another 5
hours and then 2 hours at 400LM
(20%) brightness until dawn for
better early morning ambient light
Mode 1 & 2: Phase 4: At anytime
during the night, if people come near
the lamp, it will turn up to 2000LM
(100%) for 30 seconds delay