Light Projects EVICA EP40 User manual

Contents
Safety instructions and precautions
Installation
Operation
Cleaning and maintenance
Service
Guarantee
Specication
Model: 5371xx EP40
Supply: 24Vdc 1.9A – Use only with approved 24VDC power supply provided
Mounting: Suitable for direct mounting on normally ammable surfaces.
Ingress protection: IP20 - Designed for indoor use only and should not come into contact
with water or excessive dust.
Maximum operating temp. : 43° Celsius – Not for use in hot locations or in direct sunlight
Safety instructions and precautions
• Follow these instructions carefully to ensure the safe and reliable operation of this product.
• Retain this sheet for future reference.
• Never look directly into the beam or shine in anyone’s eyes.
• Do not block the ventilation inlets or outlets on the unit.
• Ensure that there is sufcient ventilation around the unit, recommended minimum 1m².
• No user serviceable parts inside.
• Use only approved accessories.
• Do not use this device in the presence of ammable or oxygen rich atmospheres.
• To prevent injury, this apparatus must be securely attached to the ceiling/wall.
Installation
Prior to mounting the unit, please refer to the distance/spot size charts below & framing guide to achieve
the required image size.
Attach the projector to mount bracket but screwing the ¼” stud on top of ball joint into the threaded hole
in top of projector. Place washer against projector, then nut and screw into place until tight. Lock by
tightening nut against projector housing.
Distance Diameter
4m
3m
2m
1m 0.57m
1.14m
1.71m
2.28m
32°
Narrow Lens Wide Angle Lens
Distance Diameter
4m
3m
2m
1m 0.30m
0.60m
0.90m
1.20m
17°
24Vdc
Light Projects 23 Jacob St London SE1 2BG Tel [phone]
Website www.lightprojects.co.uk Email [e-mail] pg 1
EVICA EP40 24VDC LED EFFECTS PROJECTOR
Distance Diameter
4m
3m
2m
1m 0.44m
0.89m
1.33m
1.77m
25°
Medium Angle Lens

Contents
Safety instructions and precautions
Installation
Operation
Cleaning and maintenance
Service
Guarantee
Specication
Model: 5371xx EP40
Supply: 24Vdc 1.9A – Use only with approved 24VDC power supply provided
Mounting: Suitable for direct mounting on normally ammable surfaces.
Ingress protection: IP20 - Designed for indoor use only and should not come into contact
with water or excessive dust.
Maximum operating temp. : 43° Celsius – Not for use in hot locations or in direct sunlight
Safety instructions and precautions
• Follow these instructions carefully to ensure the safe and reliable operation of this product.
• Retain this sheet for future reference.
• Never look directly into the beam or shine in anyone’s eyes.
• Do not block the ventilation inlets or outlets on the unit.
• Ensure that there is sufcient ventilation around the unit, recommended minimum 1m².
• No user serviceable parts inside.
• Use only approved accessories.
• Do not use this device in the presence of ammable or oxygen rich atmospheres.
• To prevent injury, this apparatus must be securely attached to the ceiling/wall.
1.
6.
2.
5.
3.
Operation
1. Gobo projector only: Remove Gobo cassette by
unscrewing 2 socket head screws in the side of the
projector. Place the gobo slide into recessed pocket in
the
cassette and hold in place with the gobo retaining ring.
Gobo image should be upside down and back to front.
2. Slide the cassette into the slot in the side of the projec-
tor and x side screws.
3. Connect power as detailed above.
4a. Framing projector only: Insert the shutter blades
into the gap behind the cassette and position as detailed
on next page.
4b. Gobo projector only: Rotate cassette ring to orien-
tate image as required.
5. Focus the projected image by rotating the objective
lens bezel. The lens may also be coarsely positioned by
simply pulling the lens to the desired position and then
twisted to provide ne focus.
6. To reposition the projector, loosen the buttery screw,
position as desired and tighten the buttery screw to x
into position.
Connect to 24V DC Power supply.
For Remote versions, attach Jack connector from Power Supply to receptacle at back of Projector.
Fix the projector to the bracket by inserting the screw thread on the top of the bracket into the projector
and screwing in place until tight.
For Ceiling Mount versions, attach cable from Power Supply to terminals in Ceiling plate & plug Jack
connector lead into receptacle at back of Projector.
Red wire = 24V +ve Black Wire = 24V -ve (See Power Supply for alternative colours)
For Track Mounted versions, attach Jack connecter to Projector then attach Adapter to Track.
Switch on Supply and check LED is operational.
4.
24Vdc
Light Projects 23 Jacob St London SE1 2BG Tel [phone]
Website www.lightprojects.co.uk Email [e-mail] pg 2

Figure 1: Select mounting location so that object to light is fully
within the open beam.
Figure 2 shows cassette removed from projector for clarity.
Figure 3:
1. Place I shaped blade (1) onto cassette next to the xing screw side.
2. Place T shaped blade (2) onto cassette on opposite open side.
Figure 4:
3. Place the remaining 2x T blades (3) and (4) onto cassette, on top of
blades (1) and (2).
To frame object:
1. Pull all blades out of beam, leaving just I blade (1) in the beam.
2. Adjust lens position to focus on the edge of the blade. For coarse
adjustment, push lens out/in from projector. For ne adjustment,
rotate lens.
3. When lens focus position is found, adjust projector orientation to
centre beam on lit object.
4. Starting with blade (1), move blade to cut edge of beam as desired.
5. Note that blades will project to opposite side of image as shown in
gures 4 & 5
6. Moving side blades may move top & bottom ones as well, so
set (1) and (2) rst and then (3) and (4).
1
1
2
2
4
3
Framing Objects with Shutter Blades
1
3
4
2
Figure 2
Figure 1
Figure 3
Figure 4 Figure 5
24Vdc
Light Projects 23 Jacob St London SE1 2BG Tel [phone]
Website www.lightprojects.co.uk Email [e-mail] pg 3

Cleaning and Maintenance
Periodically clean the projection lens with a lint free cloth and a small amount of glass cleaner if neces-
sary.
Check that the ventilation inlet and outlets are free from dust or blockages, clean with a vacuum cleaner
nozzle if necessary.
Notice
The information contained within this document is subject to change without notice.
Evica products are manufactured in the United Kingdom (UK) in partnership with Evica Ltd and covered
by Evica Ltd.’s guarantee as summarised below.
EP40 is a trademark of Evica Ltd.
No further warranty of any kind is made with regard to this material, including, but not limited to, the
implied warranties of merchantability and tness for a particular purpose.
No liability is accepted for errors contained herein or for incidental or consequential damages in connec-
tion with the furnishing, performance, or use of this material.
No part of the document may be photocopied, reproduced, or translated to another language without
prior written consent of Light Projects Ltd.
Service
In case of a fault please contact inf[email protected]
Guarantee Summary
The Evica product range is provided with a 5 year guarantee against manufacturing and material defects
when installed according to the product specication and used under recommended working conditions.
Modications or improper use deem the warranty void.
Limits of the guarantee: At its sole discretion, Evica Ltd agrees to repair or replace products it deems
to be defective and reserves the right to replace a product with a like replacement that fulls the same
purpose. This replacement product may have graphics or nishing different from the original.
It is the product users responsibility to examine the product on a regular basis to determine the need for
servicing and or a replacement.
Products that have been neglected, modied or poorly maintained are not covered under the guarantee.
Damage from causes other than defects in materials and workmanship (e.g. lack of experience, ability or
competence) are not covered under the guarantee.
The nish or aesthetics of Evica products are not covered under the guarantee.
Any labour or postage costs associated with the removal, replacement or reassembly of the product are
not covered under the guarantee.
Normal wear and tear and maintenance are not covered under the guarantee.
24Vdc
Light Projects 23 Jacob St London SE1 2BG Tel [phone]
Website www.lightprojects.co.uk Email [e-mail] pg 4

Additional instructions for Evica EP40 Effects Projector Remote Dimmable 0-10V Models.
The internal LED driver is dimmable by use of a remote Current Source or Sink 0-10V Dimmer.
Projector is tted with an additional 2 core cable with jack plug to connect to the dimmer
Red Core = +ve output of Dimmer
Black Core = -ve coutput of Dimmer
Follow general instructions for installation of Projector.
Connect Dimming wires, which are connected to the black marked terminal block, to Remote 0-10V
dimmer.
Connect:
Black to Black (-) -ve 0-10V
Red to Red (+) +ve 0-10V
Connect Low Voltage 24Vdc power supply to white terminal block.
Connect:
Black to Black (-)
Red to White (+)
Attach EP40 projector to Ceiling Mount Ball Joint.
Plug 24V & 0-10V leads from ceiling mount into back of EP40 projectors.
If 0-10V signal is diconnected, the LED with come on at full output.
With dimmer connected, adjust dimmer to achieve desired intensity.
Rev: 20.12
24Vdc
Light Projects 23 Jacob St London SE1 2BG Tel [phone]
Website www.lightprojects.co.uk Email [e-mail] pg 5