Light MH-200 Hybrid Pro V2 User manual

MH-200 HYBRID PRO V2
MANUAL

2
Unpacking: Thank you for purchasing MH-200 Hybrid Pro V2. Every unit has been thoroughly
tested and has been shipped in perfect operating condition. Carefully check the shipping carton
for damage that may have occurred during shipping. If the carton appears to be damaged,
carefully inspect your fixture for any damage and be sure all accessories necessary to operate the
unit has arrived intact. In the case damage has been found or parts are missing, please contact
the manufacturer or your dealer for further instructions. Do not return this unit to your dealer
without first contacting.
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE POWERING OR
INSTALLING MH-200 HYBRID PRO. SAVE IT FOR FUTURE REFERENCE.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself;
doing so will void your manufactures warranty. In the unlikely event your unit may require service
please contact the manufacturer or your dealer.
General Instructions: To optimize the performance of this product, please read these
operating instructions carefully to familiarize you with the basic operations of this unit. These
instructions contain important safety information regarding the use and maintenance of this unit.
Features
Multi-Colors+gobos
Color strobe
Electronic Dimming 0-100%
DMX-512 protocol
Master/Slave synchronization
LCD operation menu with function
buttons
Daisy Chain Units Together in DMX
Mode
Safety Precautions
To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.
Do not spill water or other liquids into or on to your unit.
Be sure that the local power outlet matches that of the required voltage for your unit.
Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to remove
or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical
shock and fire in case of an internal short.
Disconnect from main power before making any type of connection.
Do not remove the cover under any conditions. There are no user serviceable parts inside.
Never operate this unit when it’s cover is removed.
Never plug this unit in to a dimmer pack.
Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm)
between this device and a wall.
Do not attempt to operate this unit, if it becomes damaged.
This unit is intended for indoor use only; use of this product outdoors voids all warranties.
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain
or moisture.
PLEASE consider that damages caused by manual modifications to the device are not subject
to warranty.

3
 During long periods of non-use, disconnect the unit’s main power.
 Always mount this unit in safe and stable matter.
 Power-supply cords should be routed so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to the point they exit from the unit.
 Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See “Cleaning” for
details.
 Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves,
or other appliances (including amplifiers) that produce heat.
 The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in performance.
Technical Specifications
Electrical
Power supply:……………….…electronic auto-ranging
Input voltage range:…………… 90-250V, 50/60Hz
Fuse:…………………………… 5 A@220V
Power consumption:……………300W@230V
Optic
Light source: LumiEngin 200W White LED
LED lifespan: 60000 hours
Dimmer: Smooth dimmer from 0-100%
Fixed gobo wheel: 7gobos+Open
Rotating gobo wheel: 7gobos+Open
Color wheel: 8colors+Open
6 linear+8-facet dual prisms
Motorised focus
Motorized
Pan/Tilt
Pan movement range: 540°
Tilt movement range: 270°
16 bit movement resolution
Automatic Pan/Tilt position correction
Pan movement 0°-540°at max speed: 2.2 sec.
Tilt movement 0°-270°at max speed: 1.2 sec.
LCD operation
Built-in demo sequences
Silent fans cooling
Strong three-phase motors
Stand-alone operation
Iris
Linear frost

4
Supported protocols: DMX512
2 DMX modes (19/16 control channels)
Connection
DMX data in/out: Locking 3-pin and 5-pin XLR
AC power input: 1.5m power cord with plug
Mounting system
Mounting via omega brackets (included)
Temperatures
Maximum ambient temperature: 45℃
Maximum housing temperature: 75℃
Minimum distances
Min. distance from flammable surfaces: 3.0m
Min. distance to lighted object: 2.0m
Net dimension: 428(L) x 260(W) x 678(H) mm
Weight (net): 15.9kgs
Set Up:
Power Supply: Before plugging your unit in, be sure the source voltage in your area matches the required
voltage for your MH-200 Hybrid Pro V2, The model is Auto power supply, It is workable in 90-250V/50~60Hz.
Please make sure your unit voltage matches the wall outlet voltage before attempting to operate you fixture.
Connection to the mains
For protection from electric shock, the fixture must be earthed!
Install a suitable plug on the power cord, note that the cores in the power cord are colored according to the
following table. The earth has to be connected!
If you have any doubts about proper installation, consult a qualified electrician.
Core (EU) Core (US) Connection Plug Terminal Marking
Brown
Light blue
Yellow/Green
Black
White
Green
Live
Neutral
Earth
L
N
DMX512 connection
The fixture is equipped with 3-pin or 5-pin XLR sockets for DMX input and output. The sockets are wired in
parallel.
Only use a shielded twisted-pair cable designed for RS-485 and 3-pin or 5-pin XLR-plugs and connectors in
order to connect the controller with the fixture or one fixture with another.

5
DMX-output DMX-input
XLR mounting-sockets (rear view): XLR mounting-plugs (rear view):
DMX Linking: To ensure proper DMX data transmission, when using several DMX fixtures try to use the
shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX
line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1,
the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the
DMX chain.
Operating Modes: You can use the MH-200 Hybrid Pro V2 in 4 ways:
Auto Mode - The unit will automatically chase through the different colors and built-in programs.
Slave Mode –The unit will run under slave mode.
DMX control mode - This function will allow you to control each individual fixtures traits with a standard
DMX 512 controller.
Music control mode- This function will allow you operate the fixture through music.
DMX Mode: Operating through a DMX controller give the user the freedom to create their own programs
tailored to their own individual needs. This function will allow you to control each individual fixture’s traits with
a standard DMX 512 controller.
1. The MH-200 Hybrid Pro uses 16/19 two DMX channels modes to operate. Please see “DMX Values and
Functions” for the DMX traits.
2. To run your fixture in DMX mode, plug in the fixture via the XLR connections to any standard DMX
controller. Set your desired DMX address following the setup specifications that come with your DMX
controller.
Touch Buttons: There are four buttons next to the LCD display: Up, Right, Down, Left. Normally, the LED
will display the current DMX address code of the fixture. At this time, presses up and down to choose the
functions you want.
LCD display operation:

6

7

8
Standard
Mode
Reduced Mode
DMX Value
Function
1
1
0255
Pan 0540
2
*
0255
Pan Fine 16bit
3
2
0255
Tilt 0230
4
*
0255
Tilt Fine 16bit
5
*
0255
Pan/Tilt Speed Fast-Slow
6
3
0255
Dimmer
7
4
Strobe
0-2
Open
3103
Strobe slow-fast
104107
Open
108207
Pulse Strobe 1 Slow to Fast
208212
Random Strobe 1
213238
Pulse Strobe 2 Slow to Fast
239251
Random Strobe 2 Slow to Fast
252255
Open
8
5
Color Wheel
03
Open
4127
Rotation 360
128
Open
129131
Red
132135
Yellow
136138
Blue
139142
Magenta
143146
Cyan
147150
Pink
151154
Green
155158
Orange
159207
Forward Fast-Slow
208255
Backward Slow-Fast
9
6
Static Gobo Wheel
07
Open
815
Gobo 1
1623
Gobo 2
2431
Gobo 3
3239
Gobo 4
4047
Gobo 5
4855
Gobo 6
5663
Gobo 7
6470
Gobo 7 shake Fast - slow
7177
Gobo 6 shake
7884
Gobo 5 shake
8591
Gobo 4 shake
9299
Gobo 3 shake
100107
Gobo 2 shake

9
108114
Gobo 1 shake
115185
Forward Fast-Slow
186255
Backward Slow-Fast
10
7
Static Gobo Wheel
07
Open
815
Gobo 1
1623
Gobo 2
2431
Gobo 3
3239
Gobo 4
4047
Gobo 5
4855
Gobo 6
5663
Gobo 7
6470
Gobo 7 shake
7177
Gobo 6 shake
7884
Gobo 5 shake
8591
Gobo 4 shake
9299
Gobo 3 shake
100107
Gobo 2 shake
108114
Gobo 1 shake
115185
Forward Fast-Slow
186255
Backward Slow-Fast
11
8
Gobo Rotation 360
0127
Gobo index
128187
Gobo Forward Rotation(Fast-Slow
188194
Stop
195255
Gobo Backward Rotation(Slow-Fast
12
9
0128
Iris pulse
129190
Iris Pulse open
191255
Iris Pulse closed
13
10
0127
NO
128255
Frost
14
11
Prism
010
NO
11128
Prism 1 8 faced
129255
Prism 2 6 linear
15
12
Prism1 Rotation
0128
Prism 1 index
129187
Prism 1 Backward Rotation Fast-Slow
188195
Stop
196255
Prism 1 Forward Rotation Slow-Fast
16
13
Prism2 Rotation
0127
Prism 2 index
128187
Prism 2 Backward Rotation Slow-Fast
188195
Stop
196255
Prism 2 Forward Rotation Slow-Fast
17
14
0255
Zoom

18
15
0255
Focus
19
16
0127
NO
128255
All-Reset
Fixture dimension 380x247x550 (mm):
Rigging the fixture
Caution: Fixture may cause severe injuries when crashing down! If you have doubts concerning the safety of a
possible installation, do not install the moving head! Before rigging make sure that the installation area can hold a
minimum point load of 10 times the fixture’s weight.
When installing the device, make sure there is no highly inflammable material (decoration articles, etc.) in a distance of
min. 1.0 m. CAUTION! Use an appropriate clamp to ring the fixture on the truss.
Follow the instructions mentioned at the bottom of the base. Make sure that the device is fixed properly! Ensure that
the structure (truss) to which you are attaching the fixtures is secure.
Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to
optimize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.
2. Clean the external optics with glass cleaner and a soft cloth every 20 days.
3. Always be sure to dry all parts completely before plugging the unit back in.
Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue, dust, dew).
Troubleshooting
Unit not respond to DMX:
1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some other DMX devices pin
5 may be ‘hot’). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and
outputs are connected.
ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE BSL B.V. | SPAARPOT 19| 5667 KV GELDROP | THE NETHERLANDS
[phone] WWW.BSL-LIGHTING.COM | WWW.LIGHT-INC.EU