Lite-Puter LPTC601 User manual

LPTC601 GB1
LPTC601 – 6-CHANNEL DIMMING CONSOLE
1. Introduction
Thank you for buying the LPTC601 ! Please read the manual carefully before bringing this
device into service.
This device features 6 channels with LED indication, 6 flash buttons and an external master
input.
Make sure that the device was not damaged in transit. If the device is damaged, you should
contact your dealer and postpone installation of this device.
2. Safety Instructions
• A qualified technician should install and service this device.
• Damages caused by disregarding certain guidelines in this manual are not covered by the
warranty and the dealer will not accept responsibility for the ensuing defects or problems.
• do not switch the device on immediately if it has been exposed to changes in temperature.
Protect the device against damage by leaving it switched off until it has reached room
temperature.
• This device falls under protection class III.
• make sure that the available voltage does not exceed the voltage stated in the specifications
of this manual.
• Do not crimp the power cord and protect it against damage from sharp edges. Ask an
authorised dealer to replace the cord if necessary.
• Always disconnect the device from the mains when it is not in use or when you wish to clean
it. Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
• Do not look directly into the light source as sensitive people may go into epileptic seizure if
they do.
• Be aware that damages caused by user modifications to the device are not covered by the
warranty. Keep the device away from children and unauthorised users.
Protect this device against rain and moisture
Unplug the supply cable before you open the housing
Be very careful when installing the device : touching
live wires can cause life-threatening electroshocks.
Do not touch the device during operation as the housing heats up

LPTC601 GB2
3. General Guidelines
• This device is a light controller for professional use on stages, in discos, theatres, etc. This
device should only be operated with a direct current of 20Vdc supplied by a dimmer pack e.g.
LPTP406 or LPTDX625. This device is designed for indoor use only.
• Do not shake the device. Avoid brute force when installing or operating the device.
• Select a location where the device will be protected against extreme heat, moisture and dust.
• Do not use or transport the device under temperatures < 5°C or > 35°C.
• Familiarise yourself with the functions of the device before actually using it. Do not permit
operation by unqualified people. Any damage that may occur, will probably be due to
unprofessional use of the device.
• Use the original packaging if the device is to be transported.
• Note that all modifications of the device are forbidden for safety reasons.
• Do not remove the serial number sticker from the device as doing so will void the warranty.
Only use the device for its intended purpose. All other uses may lead to short-circuits, burns,
electroshocks, lamp explosion, crash, etc. Using the device in an unauthorised way will void
the warranty.
4. Front & Back Panel Description
1. LED indicators for each channel.
2. Possibility to dim each channel through a slide control
3. FLASH buttons : one push button per channel to bring each channel to 100% output
4. MASTER FADER : sets the output level for all 4 channels
5. MASTER LED : LED indication for the master dimming control
1. LED indicator per
channel
2. dimming control
per channel
3. flash control per
channel
5. master LED
indicator
4. master dimming
control

LPTC601 GB3
5. Connections
Neither the manufacturer nor your local dealer will be held responsible for damage caused by
improper connections. Connect the device to an appropriate dimmer/power pack (LPTP406 or
LPTDX625) by connecting the 8-pin DIN output socket of this device to the 8-pin DIN input
socket of the dimmer pack. The external 5-pin DIN connection "EXT" is the power input.
Use the slide controls to dim individual channels and dim all channels simultaneously with the
master slide control. Push a flash button to instantly bring a channel to 100% output.
6. Cleaning and Maintenance
1. All screws should be tightened and free of corrosion.
2. The housing, mounting supports and connections should not be modified or tampered with
e.g. do not drill extra holes in mounting supports, do not change the location of the
connections, …
3. The electric power supply cables should be undamaged. Have this device installed by a
qualified technician.
7. Caution
• Disconnect the device from the mains prior to maintenance.
• Use a moist cloth to clean the device and avoid the use of alcohol or solvents for cleaning
purposes.
• This device does not contain any user-serviceable parts. Replace a blown fuse with an
identical one.
• Spare parts should be ordered with your local dealer.
8. Technical Specifications
Power Supply 20Vdc through power/dimmer pack (LPTP406 or
LPTDX625)
Number of Channels 6
Analogue Output Connection 1 x 8-pin DIN socket, 6 channels (0-10Vdc)
Additional Master Output 2-pole screw connector
Dimensions 164 x 177 x 72mm
Weight 1.2kg
The information in this manual is subject to change without prior notice.