Lightcloud LCHUB User manual

Functionality
TOP and BOTTOM BUTTON
Control devices or scenes after configuration.
For status light definitions, please
visit lightcloud.com/hubstart
APPLICATION
STATUS
BLUETOOTH
WIFI
UPDATES
TOP BUTTON
BOTTOM
BUTTON
DEVICE RESET
PINHOLE
DIM LEVEL
POWER
Welcome
Hub
1 (844) LIGHTCLOUD
or 1 [phone]
WE’ RE HER E TO HELP:
Hello
PART NUMBER
LCHUB
INPUT
120-277VAC, 50/60Hz, 2W
OPERATING TEMPERATURE
-20°C to 40°C
DIMENSIONS
Hub: 1.77"W x 2.7"H x 1.49"D
Faceplate: 2.94"W x 4.69"H x 0.06"D
Faceplace Bracket: 2.8"W x 4.55"H x 0.13"D
TERMINAL
18AWG grounding
Terminals supporting up to
12AWG wire
WIRELESS RANGE
Line-of-Sight: 1000’
Obstructions: 100’
Specications
Contents
Hub Faceplate
Faceplate Bracket Instruction Manual
2x 6-32 1/2” Screws 2x 6-32 5/16” Screws
The Lightcloud Hub is a powerful lighting control
system in the body of a Dimmer.
The Hub acts as the brain of the system and has an
integrated Dimmer for remotely controlling
scenes and zones.
For a complete system, you will need one or more
Lightcloud Controllers, Outlets, or enabled fixtures.
27278-I
LCHUB_Manual_0720-PRINT.pdf 1 7/8/20 12:31 PM

1 (844) LIGHTCLOUD
WE’ RE HERE TO HEL P:
or 1 [phone]
Setup & Installation
Start up
WARNING
OFF
OFF
1Turn off power
2Install the Lightcloud Hub
2a Connect the Line,
Neutral, and Ground
to screw terminals.
2b Use the two 6-32 1/2" Phillips round
head screws to secure the Hub to
the junction box.
2c Use the two 6-32 5/16"
Phillips flat-head
screws provided to
secure the faceplate
bracket to the Hub.
2d Snap the faceplate
onto the faceplate
bracket.
FCC Information:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
Note: This device has been tested and found to comply with the limits for
Class B digital devices pursuant to Part 15 Subpart B, of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential environment. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try and
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
To comply with FCC RF exposure limits for general population/
uncontrolled exposure, this transmitter must be installed to provide a
separation distance of at least 20cm from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter.
CAUTION: Changes or modications to this equipment not expressly
approved by RAB Lighting, Inc. may void the user’s authority to operate
this equipment. Custom manufactured in China.
Make sure
the arrow
labeled “TOP”
is pointing up.
© RAB Lighting Inc
170 Ludlow Avenue, Northvale, NJ 07647
Designed by RAB in the USA. Made in China.
• Use only copper wire.
• Do not operate with the
faceplate removed.
• This product should only be
installed by a qualified
electrician and in
compliance with local and
national electrical codes.
• This product should only be
installed in a UL-approved
wall-box enclosure
• Indoor use only.
For App download*and configuration instructions,
please visit lightcloud.com/hubstart
*Note: Requires IOS or Android device
LCHUB_Manual_0720-PRINT.pdf 2 7/8/20 12:31 PM