lightMoods MNFLSC-24V-72 User manual

Single End Connection Application Accessories Kit
01 (or 02) Front Connector
Silicon Gasket
U Steel Plate
Anti-skidding Clip
1 pc
1 pc
1 pc
1 pc
Front Connector Accessories Kit
End Cap Accessories Kit
The Tail Plug
U Steel Plate
Anti-skidding Clip
Silicon Gasket
1pc
1pc
1pc
1pc
Fig.1Minimum bent diameter 90mm
Light Surface
Φ90mm
LightMoodsTM
MINI Flat LED Neon Ribbon Light
USER MANUAL
MNFLSC-24V-72
(Green/Blue/Warm White/White/Cool White/Daylight White)
1. Model: MNFLSC-24V-72
2. Rated input voltage: DC 24V
3. Rated Power: 5W/m
4. Dimension: 9*18mm
5. LED quantity: 72LEDs/mtr
6. LED Spacing: 13.88mm
7. Min. cutting length: 83.3mm( 6LEDs)
8. Max. running length: 15 mtrs for single end feed or 30mtrs
for double ends feed.
9. Light color: Single Color
(Green/Blue/Warm White/White/Cool White/Daylight White)
10. Min. bent diameter: 90mm; Do not twist the light .
11.Protection rate: IP68
12.Protection rate for IP68: Protected against dust and submersion
in water (1meter above).
NOTE: All connector joints must be connected correctly to achieve
IP68 rating
13.Can be cut and extended
14.Long lifetime: 5 years
15.Working ambient temperature: -4°~113°F (-20°~45°C)
16.Operating (bending) ambient temperature: 32°~113°F (0°~45°C)
Palm Coast, Florida, USA / Los Angeles, California, USA / Pribram, Czech Republic / Birmingham, U.K. / Kuala Lumpur, Malaysia / Mumbai, India
Email: [email protected] / Web: www.aveoengineering.com
DO-160G
tested
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION AND LEAVE A COPY FOR THE END
USER/MAINTENANCE ENGINEER FOR FUTURE REFERENCE
FEATURES WARNING AND CAUTION
ACCESSORIES (SOLD SEPARATELY)
ASSEMBLY AND INSTALLATION
FIGURES
WARNING
1. Before making any cuts,installation,maintenance or connection, be sure
the mains is disconnected!
2. NOTE: ALL CONNECTOR JOINTS MUST BE CONNECTED CORRECTLY TO
ACHIEVE IP68 RATING.
3. Please operate this ex light according to the instructions, and conrm
the work voltage, it must be matched with product requirements.
4. Please conrm the polarity of connector before insertion front connection cable.
5. Connect and cut this product correctly. Any wrong operation will damage this
product.
6. No pressing on this product during storage, long term pressing may lead to damage.
7. Using qualied DC power supply.
8. Min. bent diameter 90mm, see Fig.1.
9. Do not twist the light as Fig.2 and follow the correct bending direction as Fig.3.
10. Do not hang this light in the air as Fig.4.
11. Cutting at the wrong location will result in a failure of the light! See Fig.5.
CAUTION
1. Suitable for mounting on normally ammable surfaces..
2. Use only factory-recommended connectors and accessories.
3. To ensure its long life span, operate the light properly in accordance with the
instructions.
4. Do not operate in more than 113°F (45°C) ambient temperature.
5. Assemble the DIY Connector correctly as in Fig.6.
6. Max. running length depends on the energizing way as Fig.7 shown.
7. Warm White,Cool White and Daylight color reference ANSI STANDARD.
8. Do not operate light when ambient temperature is below 32°F (0°C) thais may injure
the light .
1. Turn o the electricity before operation.
2. Cut the light at correct location (if need).
3. Assemble the light according to Fig.8.
4. Install U channel and light according to Fig.9 (Only applicable to DIY accessories) .
5. Wire all connectors to the power line and check wiring of the whole circuit.
Cable color coding basics Refer to Fig.10.

××
Fig.5Unit cutting guide
(Only applicable to DIY accessories)
Pay attention to”+” both
on light body and front
connector
Light Surface
√
Light Surface
×
×
Light Surface
×
√
Fig.2Fig.3
Recommened Use
Light Surface Light Surface
Light Surface
PCB
LED
PVC
83.3mm Cutting line
√
×
×
The correct cutting way,R=90°
Wave cutting is incorrect
R=90°is incorrect
√
×
Connector Pins
√×
Connector Pins
√×
Connector PinsConnector Pins
For 01 Type Front Connector
MINI Flat LED Neon Ribbon Light
USER MANUAL
MNFLSC-24V-72
(Green/Blue/Warm White/White/Cool White/Daylight White)
Palm Coast, Florida, USA / Los Angeles, California, USA / Pribram, Czech Republic / Birmingham, U.K. / Kuala Lumpur, Malaysia / Mumbai, India
Email: [email protected] / Web: www.aveoengineering.com
DO-160G
tested 2
Twisting the light is forbidden and observe to correct
bending orientation
Fig. 4 Installation of the light hanging suspended in the air as
the picture illustrates is forbidden. Fig.6 Correct insertion of connector pins
LightMoodsTM

MINI Flat LED Neon Ribbon Light
USER MANUAL
MNFLSC-24V-72
(Green/Blue/Warm White/White/Cool White/Daylight White)
Palm Coast, Florida, USA / Los Angeles, California, USA / Pribram, Czech Republic / Birmingham, U.K. / Kuala Lumpur, Malaysia / Mumbai, India
Email: [email protected] / Web: www.aveoengineering.com
DO-160G
tested 3
Single ends connection for Max. length 15m
Double ends connection for Max. length 30m
Fig.8DIY Connector Assemble
Diagram
For 02 Type Front Connector
Connector Pins
√×
Connector Pins
Front Connector
U Steel Plate
U Steel Plate
Anti-skidding Clip
Rubber Gasket
The Tail Plug
Light
Anti-skidding Clip
Rubber Gasket
Front Connector Assemble
Front Connector
Rubber Gasket
U Steel Plate
Anti-skidding Clip
Light
Step
1.
2.
3.
4.
5.
6.
7.
8.
Rubber Gasket
Anti-skidding Clip
Front Connector
U Steel Plate
Diagram
Push in using special wrench
①
Fig.7 Energizing Method
LightMoodsTM

MINI Flat LED Neon Ribbon Light
USER MANUAL
MNFLSC-24V-72
(Green/Blue/Warm White/White/Cool White/Daylight White)
Palm Coast, Florida, USA / Los Angeles, California, USA / Pribram, Czech Republic / Birmingham, U.K. / Kuala Lumpur, Malaysia / Mumbai, India
Email: [email protected] / Web: www.aveoengineering.com
DO-160G
tested 4
End Cap Connector Assemble
Light
Anti-skidding Clip Rubber Gasket
The Tail Plug
U Steel Plate
Step
1.
2.
3.
4.
5.
6.
7.
8.
Rubber Gasket
The Tail Plug
Anti-skidding Clip
U Steel Plate
Diagram
②Fig.9Installation Guide
Aluminum U-channel Installation Guide
Fixing Aluminum U-channel
by screw
Install the light into the
aluminum U-channel
Light
Fig.10 Cable color coding basics
(+)
(-)
1. We provide lifelong technical assistance with this product:
A 3 year warranty is given from the date of original purchase. The warranty is for free repair or replacement and covers manufacturing faults only. For faults beyond the
3 year warranty we reserve the right to charge for time and parts. Advances technology for the will be selected rstly.
2. Warranty excludes below:
Any man-made damages caused from improper operation, assembly, wiring, connection, installation, transport and storage. Improper input voltage, current, operating
and working environment. The product appears to have excessive physical damage. Damage due to natural disasters and force majeure. Product label or data code have
been damaged.
3. Repair or replacement as provided under this warranty is the exclusive remedy to the customer. We shall not be liable for any incidental or consequential damages for
breach of any stipulation in this warranty.
4. Any amendment or adjustment to this warranty must be approved in writing by us only.
5. This manual only applies to this model. We reserves the right to modify the manual and keep the right to make nal edition of this manual.
GUARANTEE
ANSI STANDARD
Nominal CCT Categories
Target Duv and tolerance
2700K 2725 ± 145 0.000 ± 0.006
3500K 3465 ± 245 0.000 ± 0.006
4500K 4503 ± 243 0.001 ± 0.006
5700K 5665 ± 355 0.002 ± 0.006
Nominal CCT Target CCT and tolerance(K)
LightMoodsTM