Lightolier 4" RECESSED EVOLUTION User manual

IS:C4P20MH
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To
assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTALLATION INSTRUCTIONS FOR 4", 6", AND 7" RECESSED
EVOLUTION H.I.D. DOWNLIGHT TRIMS.
INSTRUCTION SHEET NO.
B0904 Page 1 of 2
A COMPANY
631 Airport Road, Fall River, MA 02720
CAUTION: (RISK OF FIRE) DO NOT INSTALL INSULATION ABOVE NOR WITHIN 3 INCHES (76mm) OF ANY
PART OF THE LUMINAIRE (LIGHTING FIXTURE)
CAUTION: USE ONLY ROUGH-IN SECTIONS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURERS’ ROUGH-IN KITS
WILL VOID THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.
PAR-type Open
Downlights,
1-Piece Construction ED17 Horizontal Lamp
1-piece Construction
LAMPHOLDER
(supplied with frame)
LAMPHOLDER
SPRING
(supplied with frame)
REFLECTOR NECK
Fig. 1
Installing Lampholder onto Reflector (Fig. 1)
1. Bring LAMPHOLDER through frame opening into workspace.
2. Snap LAMPHOLDER SPRING into two slots on REFLECTOR NECK.
3. Check to make sure that both sides of LAMPHOLDER SPRING are fully engaged into slots.
4. Reflector trim is now ready for installation into ceiling.
Installing Reflector into Frame (Fig. 2)
1. Install LAMPHOLDER onto REFLECTOR NECK.
2. Feed assembled REFLECTOR into frame opening by aligning as shown, and pushing up on FLANGE until it is fully installed into
frame opening.
Re-lamping
1. To re-lamp one-piece units, simply unscrew the old lamp and replace with a new one. There is no need to remove trim from ceiling.
2. For two-piece constructions, remove CONE by pulling out of trim assembly, re-lamp, and then replace CONE.
3. See trim labeling for correct lamp info. Follow lamp manufacturer's directions for proper care and handling of lamp.
PAR-type Open
Downlights,
2-Piece Construction
TRIM
RETENTION
SPRING
Fig. 2
CONE

IS:C4P20MH
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To
assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTALLATION INSTRUCTIONS FOR 4", 6", AND 7" RECESSED
EVOLUTION H.I.D. DOWNLIGHT TRIMS.
INSTRUCTION SHEET NO.
B0904 Page 2 of 2
A COMPANY
631 Airport Road, Fall River, MA 02720
CAUTION: (RISK OF FIRE) DO NOT INSTALL INSULATION ABOVE NOR WITHIN 3 INCHES (76mm) OF ANY
PART OF THE LUMINAIRE (LIGHTING FIXTURE)
CAUTION: USE ONLY ROUGH-IN SECTIONS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURERS’ ROUGH-IN KITS
WILL VOID THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.
FRAME RING
LEAF SPRING
CONE
RETENTION
SPRING
REFLECTOR
HOUSING
Installation of 2-piece type construction
1. Install REFLECTOR HOUSING into FRAME
RING by aligning LEAF SPRINGS with slots in
upper portion of FRAME RING.
2. All LEAF SPRINGS must fully engage with
slots for correct installation.
3. Install CONE by pushing up into opening.
CONE RETENTION SPRINGS will hold CONE
in place.
Detail of Lens Removal and Replacement
1. On some trims, it will be necessary to remove
the lens prior to re-lamping.
2. To remove LENS, push on one LENS
RETENTION SPRING to disengage it from the
edge of the LENS.
3. The LENS should easily come free from the
remaining LENS RETENTION SPRINGS.
4. To replace, insert edge of LENS into all but one
of the LENS RETENTION SPRINGS.
5. Push LENS up to snap it into the remaining
LENS RETENTION SPRING.
PUSH
LENS
LENS
RETENTION
SPRING
ED17 Horizontal Lamp
2-piece Construction
**Care and Maintenance of “Alzak” REFLECTOR TRIM finish:**
If handling of REFLECTOR TRIM with anodized or Alzak finish is required, the use of clean white or
plastic film gloves is recommended to avoid fingerprints.
A
nodized or Alzak surfaces can be cleaned by the following methods:
1. Wipe off with a soft, clean, dry, lint-free cloth.
2. Wipe off with a soft clean cloth dampened in mild detergent solution.
Rinse, then wipe dry with lint-free cloth or paper towel.
3. Wipe off with a clean cloth dampened with a solution of wetting agent and water (such as 2 oz. Per
gallon “Pluronic L62-LF” by Wyandotte Products). Wipe dry.
4. Use a liquid wax such as Glass Wax®. Avoid gritty cleaning agents.
CONE