Lightolier DL System User manual

Lightolier is a Philips group brand
DL System
Fluorescent Daylight Harvesting

DL System
Fluorescent Daylight
Harvesting Made Easy
ULM-EZR Module blends in with the ceiling system.
Even when you have selected the most energy
efficient luminaire/ballast/lamp combination for
your space, additional energy savings can be
made by utilizing natural daylight through use of
controls. In the past, many have felt "Daylighting"
was too complicated because of the wiring
required for the interface of the fixtures to the
control sensors, the adjustability of the sensors
and the inflexibility if you relocated furniture or it
did not quite work to your satisfaction.
ULM-EZR Module can be relocated at any time with out use of tools.

ULM-EZR module sensor placement guidelines:
Before adjusting sensor settings, check to make sure they have
been installed in accordance with the following guidelines:
Sensor SHOULD be located
• Between 6-10’ away from window
• Over work surfaces
Sensor should NOT be located
• Over very dark surfaces (e.g. dark carpet or furniture)
• Over highly reflective surfaces (e.g. polished floors or tables)
• Outside the daylit zone (typically beyond 15’ from window)
NOW, LIGHTOLIER makes DAYLIGHTING as EASY as 1-2-3
Install Lightolier recessed luminaires* which include a
0-10 volt dimming ballast and the #EZR option per
your Lighting Layout and connect to AC power
as you normally would any recessed
luminaire.
Install a ULM-EZR module in the ceiling, positioning it 6 to 10 feet from windows
and over a work surface (it must be within 10 ft of a luminaire).
Using the low voltage plug-in 12' long CAT5 cables provided with the
luminaires*, connect the luminaire and ULM-EZR module.
An additional CAT5 cable will be provided with each luminaire* to plug in
additional luminaires* as in a daisy chain. Up to 20 luminaires* can be
connected to a single ULM-EZR module.
ULM-EZR modules can be moved or added at any time merely by plugging or
unplugging the CAT5 cables.
Both ULM-EZR modules and fixtures have proprietary RJ45 dual receptacles for
the CAT5 cable with RJ45 plugs.
When there is no daylight, place a lightmeter on the work surface and take a
footcandle reading.
Adjust to desired footcandle level by rotating the sensor in the face of the
ULM-EZR Module.
The sensors are factory pre-calibrated to 45fc on the horizontal,
assuming standard reflectances (80/50/20), ceiling heights
(8-10’) and work surfaces (2.5’).
To return to the default setting, rotate the aperture until it ‘clicks’
back into place at the mid-point.
To get MORE light on desk from the
luminaire, close aperture by rotating
it counter-clockwise.
The lamps will get brighter.
To get LESS light on desk from
the luminaire, open aperture
by rotating it clockwise.
The lamps will dim down.
1.
1.
2.
2.
3.
3.
Ordering Guide:
The DL System is the combination of the ULM-EZR Module (UF2F-EZR) and a Lightolier recessed fluorescent fixture* with a 0-10 volt dimming ballast and
the #EZR option. This option includes integrated RJ45 receptacles and a 12 foot long CAT5 cable.
The Module and luminaire need to be ordered separately.
ULM-EZR Module: Catalog Number UL2F-EZR
DL System Fixture: Specify a Lightolier recessed fluorescent fixture* with a 0-10 volt, 2 wire, dimming ballast and then add suffix #EZR
Example: CFS2GPF232UNVM7-#EZR
M7 Denotes Advance Mark VII dimming ballast for this lamping configuration. Other lamping configurations and dimming ballast manufacturers available.
*Consult your Lightolier representative for list of DL System compatible 1' X 4', 2' X 2' and 2' X 4' recessed fluorescent fixtures.
UL2F-EZR Module

Lightolier is a Philips group brand
631 Airport Road
Fall River, MA 02720
Phone [phone]
Fax [phone]
www.lightolier.com
3015 Rue Louis Amos
Lachine (Quebec) H8T 1C4
Phone [phone]
www.canlyte.com
© 2008 Philips Group.
All rights reserved. Certain
products illustrated in this
catalog may be protected
by applicable patents and
patents pending. Lightolier
will aggressively defend all
of its intellectual property.
We reserve the right to
change details of design,
materials and finishes.
A.I.A. Division 16
Brochure LOL7100
Folio A20-05
Some luminaires use fluorescent
or high intensity discharge (HID)
lamps that contain small amounts of
mercury. Such lamps are labeled
“Contains Mercury” and/or with the
symbol “Hg.” Lamps that contain
mercury must be disposed of in
accordance with local requirements.
Information regarding lamp recycling
and disposal can be found at
www.lamprecycle.org.
Printed in the U.S.A.