LIGHTSIDE DOUBLE BEAM User manual

1. Specifications
Power Supply:
AC100-240V,50-60Hz
Power Consumption:
60W
LED Source:
2*10W 4IN1 (RGBW) CREE LEDs
Beam Angle:
25°
Dimmer:
0~100% Linear Dimming
Control mode:
DMX 512,Master-slave,Auto run,Sound-activated
DMX Channel:
9/17CH
Rotation Angle:
X 540 degree / Y unlimited rotation
Dimming: 0%-100% linear dimming
Connector:
DMX via 3-pin XLR cable
Date In and out:
3-pin XLR cathode and anode plug
Advantages:
1.Infinite rotation
2.Novelty double sided beam effect
3.Control each side individually
4.LCD display,small size,compact design
Cooling System:
Low noise and efficient fan cooling system
N.W/G.W:
2.5kg/3kg
Dimension:
155*140*230 mm
Outer Packing size:
380*350*300mm(4pcs/CNS)
2. SAFETY INTRODUCTION
• If the device has been exposed to temperature changes due to environmental changes,
do not switch it on immediately. The arising condensation could damage the device.
Leave the device switched off until it has reached room temperature.
• It is essential that the device is earthed. A qualified person must carry out the electric
connection.
• Make sure that the available voltage is not higher than stated at the end of this manual.
• Make sure the power cord is never crimped or damaged. If it is damaged, ask your
dealer or authorized agent to replace the power cord.
• Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power cord by plug. Never pull out the plug by tugging the power cord.
• DISCONNECT DEVICE: Where the MAINS plug or an appliance coupler is used
as the disconnect device, the disconnect device shall remain readily operable.
• Due to the magnifying type lens, please keep the lens out of contact with direct us.
Direct we can cause heat to build up inside of the unit, which will seriously damage
unit.
CAUTION:

1. Be very careful during installation. Since you will be working with a dangerous
voltage you can suffer a life-threatening electric shock when touching live wired.
2. Never look directly into the light source, as sensitive persons may suffer an
shock.
3. Please be aware that damages caused by manual modifications to the device are not
subject to warranty. Keep away from children and non-professionals.
4. The light doesn’t include any spare parts for repair, please check if all the parts are
well installed and screws are fitted tightly before operating. Do not use the light when
the cover is open.
GENERAL GUIDELINES
• This device is only allowed to be operated with an alternating current of max.
220-240VAC/50-60Hz and was designed for indoor use only.
• Do not shake the device. Avoid brute force when installing or operating it.
• Operate the device only after having familiarized yourself with its functions. Do not
permit operation by person not qualified for operating the device. Most damages are
the result of unprofessional operation.
• Please use the original packaging if the device is to be transported.
• For safety reasons, please be aware that all modifications on the device are
forbidden. Furthermore, any other operation may lead to short-circuit, burns, electric
shock, lamp explosion, crash, etc. If this device will be operated in any way different
to the one described in this manual, the product may suffer damages and the guarantee
becomes void.
3. Operation
1.Illustration Part
：
A.Menu
A B C D B.Up
C.Down
D.Enter

Operating Instructions: Press button A
“
Menu
”
to choose different functions ，
Press button “B” or “C” to amend parameter values, Press button “D” to“Enter”
LCD display different functions:（Press button“Enter” to enter）
NO. Display Function
1
ADDR
A001-A512 address settings
2
CHND
9CH, 17CH channel selection
3
SLND
MAST, SLAVE selection
4 SHND
Select SOUD, AUTO(SP0
—
SP9) control
5 SOUD
ON,OFF switch of sound
control
6 SENS
Sensitivity of sound control(0
closed, 100 is most sensitive)
7 BLND
YES, NO; the switch of
standby
8 LED
YES, NO; the switch of Back
light
9
DISP
YES, NO; reverse display
10
PAN
YES, NO; level motor reverse
11 TILT
YES,NO; vertical motor
reverse
12 MANU
PAN, TILT, COLOR,
GOBO,DIMM,
STROB,Manual testing
13
TEST
Automatic testing
14 HOUR
0 ---- 9999 time of use
machine
15 VER
V101 software version
number
16 RSET
YES, NO reset factory
settings
4. DMX512 Channels:

Mode 1: 9 Channels
No Functions Illustration
1
0-255
X motor operation
2
0-255
Y motor operation
3
Dimming
0-255 1-100%
4
Red Dimming
0
—
255 0-----100%
5
Green Dimming
0
—
255 0-----100%
6
Blue Dimming
0
—
255 0-----100%
7
White Dimming
0
—
255 0-----100%
8
Strobe
0-15 open light, 16-131 strobe
from slow to fast , 132-139
open light, 140-181 fast off,
slowly open, 182-189 open
light, 190-231 slow off, quick
open, 232-239 open light,
240-247 random strobe light,
248-255 open light.
9
Marco
0-69 no functional, 70-89
Close light effective when the
horizontal or vertical motor
moves, 90-109 close light
invalid when X or Y axis
moving, 110-129 close light
effectively when the color
wheel move , 130-149 invalid
to close light when the color
wheel move , 150-169 close
light effectively when Gobo
move. 170-189 close light
invalidly when Gobo move,
190-199 no functional,
200-209 overall reset,
210-249 no functional,
250-255 sound control effect
nonfunctional, 200-209
overall reset, 210-249 free
function, 250-255 random
sound control effect

Mode 2:17 Channels
No Data Illustration
1
0-255
The level of motor
travel,0
°
-------540
°
2
0-255
The level of motor tuning
3
0-255
Vertical Motor:
0-127, 360-degree stroke
positioning;
128-191, forward rotation
from fast to slow;
192 --- 255 reverse rotation
from slow to fast.
4
0-255
Vertical Motor trimming: 0
---- 255 (CH3 value is valid
when 0 --- 127)
5
Marco
0-69 non-functional, 70-89
when the horizontal or
vertical motor motor moves
off the light and effective,
90-109 when moving off light
invalid X or Y axis, 110-129
when the color wheel to move
off the light effectively,
130-149 when the color wheel
to move off the light invalid,
150-169 Gobo move off when
the light effectively, 170-189
Gobo move off when the light
is invalid, 190-199
nonfunctional, 200-209
overall reset, 210-249 free
function, 250-255 random
sound control effect
6
0-255
dimming
7
Strobe
0-7 close light, 8-15
opening,16-131 strobe from
slow to fast , 132-139 open
light, fast off slowly open
140-181, 182-189 opening,

190-231 slow off quick
opening, 232-239 opening,
240-247 random strobe,
248-255 opening
8
Red Dimming 1
0
—
255 0-----100%
9
Green Dimming 1
0
—
255 0-----100%
10
Blue Dimming 1
0
—
255 0-----100%
11
White Dimming 1
0
—
255 0-----100%
12
Red Dimming 2
0
—
255 0-----100%
13
Green Dimming 2
0
—
255 0-----100%
14
Blue Dimming 2
0
—
255 0-----100%
15
White Dimming 2
0
—
255 0-----100%
16
Self-run color
0 --- 7 No function; 8 --- 127
fixed color:15 kinds; 128 ---
191 color transitions; 192 ---
255 color gradient
17
Self-run Speed of Color
0 --- 255 from slow to fast
Motor fine-tuning operations:
Press the Menu key "MENU", enter the menu, press the Enter key
"ENTER" for at least 3 seconds or more, the menu screen displays "Pan
(X-axis motor tuning)", by plus or minus keys to select "Tilt (Y-axis
motor tuning) "press the ENTER button in the steering motor position
value range -127 ---- 127,finally, press the ENTER button to save trim
value what you have set.