Lil' Jumbl LIJDOLHOUS01 User manual

Thank you for purchasing the Lil Jumbl 3-Floor Wooden Dollhouse with Elevator and
12-Piece Accessory Set. This User Guide is intended to provide you with guidelines to
ensure that operation of this product is safe and does not pose risk to the user. Any
use that does not conform to the guidelines described in this User Guide may void
the limited warranty.
Please read all directions before using the product and retain this guide for reference.
This product is intended for household use only. It is not intended for commercial use.
This product is covered by a limited one-year warranty. Coverage is subject to limits
and exclusions. See warranty for details.
SKU: LIJDOLHOUS01
3-Floor Wooden Dollhouse with
Elevator & 12-Piece Accessory Set
User Guide
10
10
8
WARNING:
Adult assembly required. Keep away
from children when assembling
WARNING:
CHOKING HAZARD- Small parts
Not for children under 3 years.

Please read all safety precautions and instructions
carefully before using this product.
Failure to properly follow the guidelines established here
could result in serious injury.
This product is not recommended for children
under 3 years old.
Safety Precautions
Choking hazard – Small parts associated with this product
are a choking hazard for children under 3 years old.
WARNING
WARNING
WARNING
USE &
MAINTENANCE:
• Adult setup is required to assemble this product safely.
• Remove all packaging before using this product. Please keep all packaging
materials out of reach of children and pets.
• Set up indoors on an even surface.
• Always supervise children when using this product.
• Do not allow children to tip the product over. This can cause injury to children and
damage to the product.
• Do not drag the product to avoid damaging your floor and the base of the product.
• Instruct children on proper use of this product. Do not use in a manner other than
intended.
• Keep pets away from the product to avoid it tipping over and causing injury to
pets/children and product damage.
• Do not allow children to climb on this product. This can lead to injury and product damage.
• Never place computers, televisions, or other heavy objects on top of the product.
Adult assembly required – During assembly, this product
contains small components and sharp edges and points
that are potentially hazardous. Keep unassembled parts
away from children.
Use on level surfaces only. Regularly check the assembly and tighten
hardware as needed. Failure to do so may result in reduced structural
integrity and potential hazards.

Package Contents
1PC 1PC
1PC
1PC
1PC
1PC
1PC
1PC
1PC
1PC
1
6
5
2
3
7
4
8
9
10

Package Contents (continued)
1PC 1PC
1PC
1PC
1PC
1PC
1PC
1PC
1PC
11
1PC
1PC
1PC
1PC
1PC
1PC
19
12
14
13
18
20
15
21
22
16
17
24
25
26

Package Contents
Hardware
(continued)
1PC
1PC
1PC
1PC
2PCS
3PCS
1PC
33
32
30
31
27
28
29
17PCS
A
36PCS
B
4PCS
C
2PCS
D
3PCS
E
4PCS
F

Accessories
Package Contents (continued)
1PC 1PC 2PCS 1PC
1PC 1PC 1PC 1PC
10PCS1PC1PC
Recommended Tools
• Philips-head screwdriver x2 (not included) • Wrench (not included)

13
14
15
Assembly Instructions
Step 1
Elevator Assembly
• Fasten the elevator floor 13 to elevator walls 14 and 15 using four (4) B screws.
NOTE: Make sure the slots on walls 14 and 15 are pointed downward. The
slots on each wall should be on the inside facing towards each other. In
order to know the elevator is facing the right direction, the elevator
opening should be faced towards you and the wooden notches on wall 14
should point to your right. Also, the side with the beautiful design on
elevator floor 13 should be faced up towards walls 14 and 15.
B
B
B
B
B
x4

15
Step 2
• Slide the back panel 16 in between walls 14 and 15 using the slots on the walls.
16
14

16
15
Step 3
• Fasten the elevator ceiling 12 to the top of elevator walls 14 and 15 using
four (4) B screws.
B
x4
NOTE: The beautiful design on the elevator ceiling 12 should be faced
down and the flooring design on the other side should be faced up when
connecting this part.
14
12
B
B
B
B

6
Step 4
Rooftop Assembly
• Fasten the preassembled dormer 25 to the front roof panel 6 using two (2)
B screws.
CAUTION: The front roof panel 6 can be damaged or broken easily. Handle
the front roof panel 6 with care.
B
B
B
x2
25
NOTE: Use the two (2) holes adjacent to the triangular cutout found near
the center of the front roof panel 6 to attach the preassembled dormer 25.

Step 5
• Fasten the first piece of roof overhang 21 to roof frame 19 with two (2) B screws.
B
B
19
B
x2
21
NOTE: Make sure both holes are lined up between both pieces before
fastening the parts in place.

21
20
Step 6
• Fasten the second piece of roof overhang 20 to roof frame 19 with two (2)
B screws.
B
19
B
B
x2
NOTE: Make sure both holes are lined up between both pieces before
fastening the parts in place.

6
19
20
C C
C
C
C
x4
21
Step 7
• Fasten the assembled dormer 19 – 21 to front roof panel 6 using four (4)
C screws.

17
D
D
Step 8
Dollhouse Assembly
• Fasten the lower-level left wall 1 to upper-level left wall 17 using two (2)
D screws. When placing the parts together, the upper-level left wall 17
should be placed over the lower-level left wall 1 on the side with the interior
design on the wall.
D
x2
1
NOTE: The D screw is one screw with two parts: the outlet and inlet bolt.
Place the outlet bolt in the holes from the lower-level left wall 1 side. Then,
insert and screw in the inlet bolt from the upper-level left wall 17 side. Also
keep in mind when you do this you may need to use two (2) screwdrivers to
properly insert the D screws.

1
• Fasten the first-floor front border 32 to the bottom front corner of lower-level
left wall 1 using one (1) A screw.
A
A
x1
Step 9
NOTE: The first-floor front border 32 has a slot that should face inward
towards first-floor backwall border 31. Make sure that the hole on the
first-floor front border 32 is on the far right with the smaller opening of the
hole facing up and the bigger opening facing down.
32

33
1
• Fasten the first-floor backwall border 33 to the bottom back corner of
lower-level left wall 1 using another A screw.
A
A
x1
Step 10
NOTE: The first-floor backwall border 33 should have one of its slots facing
first-floor front border 32 and the other slot facing upward.

x1
NOTE: Make sure the hole on the side of the pillar is towards the top when
installing the pillar. The smaller opening of the hole should face left while
the bigger opening of it should face right.
A
• Fasten the first-floor pillar 24 to the hole on the first-floor front border 32 using
one (1) A screw.
32
24
A
Step 11

8
NOTE: Make sure the part is not fastened upside down by looking at the
design.
11
• Fasten the first-floor interior wall 11 to first-floor flooring 8 using two (2) B screws.
B B
B
x2
Step 12

8
33
Step 13
• Slide the first-floor flooring 8 with the recently connected first-floor interior wall
11 in between first-floor front border 32 and first-floor backwall border 33.
NOTE: Make sure when sliding in the first-floor flooring 8 that the first-floor
interior wall 11 ends up in the back over the first-floor backwall border 33.
32
11

A
• Line up the second-floor flooring 9 to the holes on lower-level left wall 1 and
place the flooring on top of first-floor pillar 24 and first-floor interior wall 11.
Then, fasten the second-floor flooring 9 to lower-level left wall 1 using two (2)
A screws.
11
1
10
24
Step 14
x2
9
A
A