Perma child safety 2774 User manual

Swing Down
IMPORTANT! READ AND
FOLLOW THESE INSTRUCTIONS
CAREFULLY AND KEEP FOR
FUTURE REFERENCE.
This product complies with safety standard ASTM F1004-19.
Instruction Manual
Baby Bed
Rail
#2774
35.4” (90cm) Wide
17.7”
(45cm)
Tall
INSTALLATION VIDEO

2
TABLE OF
CONTENTS
SAFETY INFORMATION
General
Maintenance
Warnings
WHAT’S IN THE BOX
Parts
INSTALLATION
Bar Installation
Mesh Installation
Positioning the Bed Rail
Minimum Distance Warning
OPERATION
Using the Bed Rail
Cleaning Instructions
SUPPORT
Warranty Certicate
Warranty Card
After Sales Support
03
03
04
06
07
08
10
11
12
12
13
14
15
15

3
SAFETY
INFORMATION
Read this instruction manual carefully and keep it in a safe place for
future reference. The correct use and maintenance of this product is
essential.
Regularly check that the bed rail is functioning correctly, lubricate
hinges and moving components with a suitable spray lubricant.
Tighten and adjust mounts to ensure secure smooth operation.
Inspect all parts regularly and stop using if any part is damaged or
missing.
GENERAL
MAINTENANCE

4
Adult assembly required.
Read all the instructions before assembly and use
of the product.
Dispose of all packaging materials carefully after
assembly.
Not suitable for use of children under the age of
18 months or when the child is over the age of 5
years.
Only use the bed rail when the child is able to climb
in and out of bed unaided.
The bed rail should not be used as a substitute for
a cot, as it cannot provide the same level of safety
as a cot.
The bed rail should be periodically checked for its
general condition with particular reference to the
security of any locking mechanism and/or hinges
that are used on the product.
The maximum thickness of mattress for which the
bed rail is suitable is 10.6” (270mm).
Intended for use with single or children’s
mattress only.
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNINGS

5
Additional and replacement parts shall be
obtained only from the manufacturer.
This bed rail should not be used on a sleeping
surface that is more than 23.6” (600mm) from
the oor.
To prevent risk of strangulation it is essential
to ensure that when the bed guard is tted
into position, there is a gap of at least 9.8”
(250mm), between each end of the bed and the
corresponding end of the bed guard.
Care should be taken in unpacking and assembly.
Fit the bed rail so that its side, when in the locked
position or when placed in the tted position,
touches the side of the mattress.
This bed rail shall not be used unless the ttings
are in place and securely attached to both the
bed and/or the mattress and the bed rail.
Once tted in place, the bed rail should be
checked to ensure that it is properly tted and
secure.
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNINGS

6
1 x
Upper Support Bar
2 x
Under Bar With Strap
1 x
Bottom Support Bar
1 x
Bed Rail Mesh
PARTS
WHAT’S IN THE BOX
PARTS

7
Insert Upper Support Bar into Bottom Support Bar. Make sure
the spring pin ts securely into opposing hole so that the two
pieces cannot pull apart.
Connect the two sides. Make sure the spring pin ts securely
into opposing hole so that the bed rail cannot pull apart.
1.
2.
STEP 1:
BAR INSTALLATION
INSTALLATION

8
To install the Mesh on the Bed Rail, slide the Mesh over the
Frame until it reaches the other end and zip it shut to complete
the installation.
1.
INSTALLATION
STEP 2:
MESH INSTALLATION

9
Insert the plastic hinge into the assembled panel and press
in the metal spring button to fully insert the tube into the hole
in the plastic hinge. The spring button should line up with the
access hole in the plastic sleeve on the hinge. The spring
button will rebound and lock the tube in place.
2.

10
1.
INSTALLATION
STEP 3: POSITIONING
THE BED RAIL
Set up the Bed Rail in locked position. Place the Bed Rail on
the side of the bed that you would like to have protected, place
the xed plate with strap on the opposite side of the Bed Rail
and mount to the outer edge of the box spring. Make sure to
adjust the slider to ensure a snug t against the base of bed.
Always readjust the slider whenever there is a change of Bed
Rail position.
LOCKED UNLOCKED

11
Check to make sure the left and right under bar assemblies are
parallel to one another, then place the mattress on the top of
the assembly.
2.
MIN 10” MIN 10”
MINIMUM DISTANCE WARNING
To prevent the risk of strangulation, it is essential to ensure that
when the Bed Rail is tted into position, there is a gap of at least 10”
(250mm) between each end of the bed and the corresponding end
of the Bed Rail.

12
1. Step up Bed Rail: Swing up the panel. Turn the locking tabs
and hold them at unlocked position. Continue to swing until
the panel touches the side of the mattress. Release the locking
tabs and the Bed Rail is locked into use position.
Fold down Bed Rail: With the locking tabs turned to the unlocked
position, hold the upper part of the Bed Rail rmly and swing it
down. The Bed Rail now should be in the down position.
LOCKED
UNLOCKED
USING THE BED RAIL
OPERATION

13
CLEANING INSTRUCTIONS
Simply use a soft damp cloth to wipe Bed Rail, dry after cleaning.
Do not use chemical or abrasive cleaners.

14
Congratulations! You have made an excellent choice of this quality product. Our commitment to
quality also includes our service. Should you, contrary to expectations, experience defects due
to manufacturing faults, we will provide you with a warranty against defects as follows:
Warranty
The product is guaranteed to be free from defects in workmanship and parts for a period of 12
months from the date of purchase. Defects that occur within this warranty period, under normal
use and care, will be repaired, replaced or refunded at our discretion. You are entitled to a re-
placement or refund for a major failure and for compensation for any other reasonably foresee-
able loss or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure.
Proof of Purchase
This warranty is valid for the original purchase and is not transferable. Please keep your
purchase docket, tax invoice or receipt as the best proof of purchase, and as proof of date on
which the purchase was made.
Extent of Warranty
This warranty is limited to defects in workmanship or parts. All defective products or parts will be
repaired or replaced. This warranty does not cover consumable items.
Normal Wear and Tear
This warranty does not cover normal wear and tear to the products or parts.
Exclusions
This warranty does not cover:
• Any defects caused by an accident, misuse, abuse, improper installation or operation,
lack of reasonable care, unauthorised modication, loss of parts, tampering or attempted
repair by a person not authorised by the distributor.
• Any product that has not been installed, operated or maintained in accordance with the
manufacturer’s operating instructions provided with the product.
• Any product that has been used for purposes other than domestic use.
To Make a Claim
If a defect in the goods appears within 12 months, you are entitled to claim a warranty. Please
contact after sales support via the link below:
www.permachildsafety.com/contact-us
Please ensure that you have a copy of proof of purchase so that we are able to respond as
quickly and efciently as possible.
WARRANTY CERTIFICATE
SUPPORT

15
Details:
Product Name: Baby Bed Rail
Product Number: G r ey 2774
Your Name:
Address:
Phone:
Email:
Date of Purchase:
Location of Purchase:
We recommend that you keep a copy of your receipt, showing the date of
purchase, with this warranty certicate and keep for your reference. In the
event of a product fault, please contact after sales support. Ensure that
you include the product details (as shown on this card) so that we are able
to respond as quickly and efciently as possible.
Product Code: G r ey 27 74
For questions, concerns and to view our latest products visit:
www.permachildsafety.com/contact-us
WARRANTY CARD
AFTER SALES SUPPORT

©2020 Permastik Pty Ltd.
All Rights Reserved.
Distributed by Perma Products USA®
www.permaproducts.com
Tel: [phone]
Made in China to Perma quality standards