lilitab Counter Pro User manual
lilitab Counter Pro
Packing List and Assembly Instructions
v.2.0
39 Larkspur Street | Suite B t: 888.705.0190
lilitab Counter Pro Packing List and Assembly Instructions v1.0 2
TABLE OF CONTENTS
LILITAB counTer Pro PACKAGING AND ASSEMBLY INSTRUCTIONS
lilitab Counter Pro Assembly Preparation ...................3
lilitab Counter Pro Features ..............................4
lilitab Counter Pro Mount Options..........................5
lilitab Counter Pro Mounting Pattern ....................... 6
lilitab Counter Pro Assembly Instructions ...................7
Using the iPad Power Button Trigger and Magkey ........... 10
lilitab Cleaning Instructions..............................11
lilitab Counter Pro Packing List and Assembly Instructions v1.0 3
ASSEMBLY PREPARATION
PACKING LIST
TO ASSEMBLE YOUR LILITAB YOU WILL NEED:
4 Phillips screwdriver
TO MOUNT YOUR LILITAB TO A SURFACE YOU WILL NEED:
4 Powered drill/driver, preferably with impact action
4 4 x bolts or wood screws (m5, no.10, no.11, 3/16” or
13/64 diameter)
lilitab Counter Pro Packing List and Assembly Instructions v1.0 4
FEATURES
MAGKEY SLOT
Accepts a MagKey for securely
sleeping an iPad.
MAGDOCK
With the turn of a key, the operator
can dock/undock the lilitab head unit.
When the head unit is docked it
automatically begins charging and it
can be docked in any orientation.
WIRELESS TRANSPARENCY
The lilitab head unit causes no
radio interference.
ROTATE FEATURE
The lilitab Counter can be
configured to allow 90,° 180°
or no rotation. By default it
is set to 180. °
To disable rotation (and/ or adjust
rotation tension) tighten the screw in
the upper rear opening of the vertical
tube to the desired level.
To switch from 180° to 90° remove
the lower screw visible through the
lower rear facing opening in the tube
using the short black L Key provided
and insert it into the threaded opening
visible through the lower front opening.
90°
180°
MULTI-POSITION NECK JOINT
Permits tilt up/down. It has two
operator configurable modes:
Fixed. The head unit can
be set to any fixed angle
between completely
vertical and +/-22.5.°
Tilt. Can be configured to
allow the user to tilt the
head unit.
lilitab Counter Pro Packing List and Assembly Instructions v1.0 5
MOUNT OPTIONS
COUNTER TOP WITH OPTIONAL BASE PLATE BOLT DIRECTLY TO COUNTER THROUGH-HOLE
(Drill 1-5/8” opening in counter, pass tube
through counter and screw up from below.
The trim ring finishes the rough opening)
lilitab Counter Pro Packing List and Assembly Instructions v1.0 6
1.50
38.10
1.50
38.10
4X M6 OR
1/4-20
1.63
41.44
.71
18
SLOT FOR POWER CABLE:
USB TYPE A,
~12" PIGTAIL
MOUNTING PATTERN
lilitab Counter Pro Packing List and Assembly Instructions v1.0 7
ASSEMBLY INSTRUCTIONS
1. Attaching directly to a counter: If you
are not using a baseplate and wish to
attach your unit directly to a counter top
(or other horizontal surface), you will
need to obtain 4 fasteners suitable for
your substrate. Use the mount pattern
provided on page 6 of this document to
mark your screw openings.
Be careful to:
• Route your usb cable (see NOTE 1) and
• Position your center of rotation (see
NOTE 2) appropriately.
Attaching to the optional baseplate:
Use the four base screws to bolt your
unit to the baseplate.
Be careful to:
• Route your usb cable (see NOTE 2) and
• Position your center of rotation (see
NOTE 3) appropriately.
NOTE 2: Center your Mount Arm
The mount arm should be positioned so that the center point of its rotation
is located appropriately for your installation scenario.
You can determine the center point by aligning the openings on the rear of
the tube with the 2 screws visible through the openings (see below).
Option 1: Surface Mount
Option 2: Through Mount
NOTE 1: Cable Routing
USB cable can exit out back of unit, through the bottom or through counter
or under baseplate.
lilitab Counter Pro Packing List and Assembly Instructions v1.0 8
ASSEMBLY INSTRUCTIONS
3. Set rotation tension. To disable rotation
(and/ or adjust rotation tension) tighten
the screw in the upper rear opening of
the vertical tube to the desired level
with the long silver L Key provided.
5. Fit screw opening caps. Once you have
adjusted the tension and degree of
rotation, insert the provided three
screw opening caps to conceal holes.
4. Set degree of rotation. The lilitab
Counter Pro can be configured to allow
90,° 180° or no rotation. By default it is
set to 180.°
To switch from 180° to 90° remove the
lower screw visible through the lower
rear facing opening in the tube using the
short black L Key provided and insert
it into the threaded opening visible
through the lower front opening.
2. Fit foot cover over screws (velcro will
hold it in place).
FRONT VIEW
REAR VIEW
6. Open the lilitab head unit by placing it
facedown on a clean surface and
squeezing the finger latches together
as shown. Carefully lift up and the
faceplate will release, allowing access
to the inside of the head unit.
7. Place the head unit onto a clean surface
with the inside of the enclosure facing
up (your charge and sync cable should
be on the right side of the enclosure
as shown in the photo). Slide all four of
the green retaining clips towards the
outside of the enclosure.
NOTE: The green keepers will not be present for
the iPad Air, Google Nexus, Samsung Galaxy Tab 3
or Samsung Note. Instead the faceplate’s locating
tabs will hold the tablet in place.
lilitab Counter Pro Packing List and Assembly Instructions v1.0 9
ASSEMBLY INSTRUCTIONS
10. Place your lilitab onto the MagDock
mount in either landscape or portrait
orientation.
TURN THE KEY to lock it in place.
WARNING: Not locking the MagDock
WILL result in the unit falling off,
possibly damaging the unit and/or the
tablet. The lilitab Pro range is designed
to be operated with the lock closed!
11. Configure head tilt. By default the head
unit can be tilted by the user to suit. If
you wish to disable tilt, position your
head unit at the desired angle and
tighten the bottom screw on the neck
joint with the long silver L key provided.
8. Plug the charge and sync cable into
your tablet’s charge port, then place
your tablet inside the enclosure face up.
If your tablet’s charge connector is in
the middle of the long edge ensure, your
charge cable is inserted into the cable
routing clips as shown in photo.
9. Slide all four green retaining clips
towards the center of the tablet.
NOTE: If clips aren’t secure, adjust your tablet.
Lastly, position the faceplate over the
tablet. Be sure to align the openings.
Gently press down around the edges it
will should snap into place.
NOTE: If the faceplate does not snap into place
evenly ensure that all four green retaining clips
are seated fully home.
lilitab Counter Pro Packing List and Assembly Instructions v1.0 10
USING THE IPAD POWER BUTTON TRIGGER USING THE MAGKEY
NOTE: Here’s an iPad installed in the
correct orientation with the Power
Button Trigger next to the iPad’s
power button.
2. Once installed you can actuate the
Power Button Trigger via a paper clip
inserted into the small opening on the
rear below the camera opening.
1. You can actuate the power button located
on the edge of your iPad using the black
Power Button Trigger shown to the left.
1. You can use the included MagKey
with an iPad 2,3 or 4 in your lilitab. The
MagKey allows you to sleep the iPad
without having any access to it. This
ensures you (and your staff!) can turn
your kiosk on and off at the end of the
day without removing the iPad from the
kiosk. You will always know when the
iPad is sleeping because once inserted
the MagKey pokes out the top of unit
like a little flag.
2. To sleep your iPad simply insert your
MagKey with the orange side facing
front and the black side facing back.
3. Remove your MagKey and your lilitab
will wake up, in exactly the same state
it was in before it went to bed ;-)
NOTE: The MagKey is compatible with iPad 2, 3
and 4. It requires that the iPad Cover Lock/Unlock
preference is turned on. You can find this in
Settings> General> iPad Cover Lock/Unlock.
Replacement MagKeys can be ordered directly from the website: www.lilitab.com
lilitab Counter Pro Packing List and Assembly Instructions v1.0 11
LILITAB CLEANING INSTRUCTIONS
1. Spray the Brillianize onto one of the
cloths provided.
WARNING: Other cloth/material may
mar the surface of your lilitab
2. DO NOT spray directly onto your lilitab!
3. Rub gently in a circular motion to remove
fingerprints and dirt.
WARNING: Applying excess pressure can
mar the surface of your lilitab.
QUESTIONS?
We’re here to help!
EMAIL: [email protected]
PHONE: (888) 705 0190
Cleaning and caring for your lilitab.
To keep your lilitab looking and working great we recommend using a lint-free cloth to gently wipe it down.
To remove and prevent fingerprints we recommend Brillianize.
DO NOT use window cleaner, ammonia-based cleaners or any type of scouring or abrasive cleaner.
Other manuals for Counter Pro
2
Table of contents
