LIMELIGHT Beds PICASSO BED 4FT User manual

ASSEMBLY INSTRUCTIONS
IMPORTANT
BECAUSE OF THE SIZE OF THIS
UNIT, WE RECOMMEND THAT IT IS
BUILT IN THE ROOM OF INTENDED
USE AND ASSEMBLED BY 2 PEOPLE.
BEFORE YOU START, HERE
IS SOME HELPFUL ADVICE.
CARING FOR YOUR LIMELIGHT BED
1. When moving your fully assembled bed, you
must first remove the mattress and lift the frame
into position. Take care when lifting to always
have two people handling the bed. PLEASE DO
NOT DRAG THE BED as this may cause
misalighment to the bedbase, making it unsafe.
2. It is advisable to use approved cleaning products
when cleaning the upholstered panels as certain
chemical based cleaners could have an adverse
effect on the fabric.
3. Depending on usage, it may be necessary to
tighten up the fittings from time to time.
PICASSO BED 4FT/4FT6/5FT
Page 1 of 6
PROBLEM?
All Limelight beds are produced to the highest
standards and are packed to avoid damages in
transit. Should you find that your new bed does
not meet your satisfaction, please contact us.
TEL: [phone]
Please have the PRODUCT NAME and PART
NUMBER ready for our staff.
See our product range online at www.limelightbeds.co.uk
IMPORTANT NOTICE
Should you need to return unassembled product . Please repack in original packaging .
If you encounter any difficulty with the assembly of
your bed, PLEASE DO NOT TROUBLE your
retailer but do contact our CUSTOMER
SERVICES DEPARTMENT at the following hours:
9AM TO 5PM on MONDAY TO THURSDAY,
9AM TO 4PM on FRIDAY.
EMAIL : [email protected]
ADDRESS:
Limelight Beds Ltd
Orbital House, Arthur Street
Barwell, Leicestershire, LE9 8GZ
1. The product you have purchased will give you
many years of service if you follow the
guidelines for its safe assembly, periodic
maintenance and cleaning.
2. Do not use any tools other than those
indicated. Use of a power tool to assemble the
product will invalidate any claim and could
make this product unsafe.
3. DO NOT DISCARD OF PACKAGING UNTIL
YOU ARE FULLY SATISFIED WITH THE
PRODUCT.Discard any excess fittings and out
of reach of children.
4. Assemble this product on a clean flat surface
to avoid any scratching.
5. Assemble all parts loosely before tightening
any bolts. Ensure bolts are fully tightened but
not forced as over-tightening may damage this
product and/or fittings.

Parts
Important information
The bed frame you have purchased comes with all the parts necessary to build you a beautiful
bed, please follow the instructions below in the current order. Before you begin building your bed
please take a moment to read through the instructions and make sure that you've got all the
relevant parts listed on the following pages.
A
BC
C
D
G
F
H
E
F
G
G
G
H
Parts list
A. Headboard 1PC
B. Footboard 1PC
C. Side Rail 2PCS
E. Centre Support Rail 1PC
F. Centre Support Rail Legs 2PCS
G. Wooden Legs 4PCS
H. Metal 'L' Bracket 2PCS
Fittings
Please check you have all the parts listed below
with your product.
12
M8x25mm Big Head Bolts
14pcs
Allen Key 1PC 4FT/4'6 34pcs
34
M8x45mm Big Head
Bolts 2pcs
M4x35mm Screw
5FT 36pcs
Page 2 of 6
D. Slat 4FT/4FT6 17PCS OR 5FT 18PCS

Step 1: Tighten the wooden leg (G) to the headboard (A) and footboard (B).
A
B
G
WRONG CORRECT
Step 2:
Step 3:
Connect the side rail (C) to the
headboard & footboard with big
head bolts (1), but do not lock it.
A
BC
C
1
3
1x8 x1
3
1x2 x1
3
x2
2
E
EH
3
F
E
2
3
1
Connect the metal 'L' bracket (H) to
the centre support rail (E).
Connect centre support rail legs (F) to
centre support rail (E).
Page 3 of 6

Step 4:
1
1
35
4
Step 5:
Connect the centre support rail (E) to
the headboard (A) & footboard (B)
with big head bolts (1).
E
D
1x4 x1
3
Lock all screws.
Affix the slat (D) to the side rail support wood.
Tighten all the self tapping screws(4).
Page 4 of 6

·When assembling your product please ensure that you have checked the contents for all relevant parts.
·When tightening bolts make sure that they are fully tightened but not forced.
Caring for your New Limelight product
BEDS WITH CENTRE LEGS
·PLEASE NOTE THE RECOMMENDED PROCESS FOR ADJUSTING CENTRE LEGS WHEN ASSEMBLING
YOUR BED.
·BEFORE PLACING THE MATTRESS ON THE BASE, PLEASE ENSURE THAT THE SUPPORT
LEGS ARE NOT QUITE TOUCHING THE FLOOR. WHEN THE BED IS THEN IN USE THE
SUPPORT LEGS WILL SIT FIRMLY ON THE SOLID SURFACE.
·PLEASE ENSURE THAT THE LEGS ARE VERTICAL.
·DUE TO THE NATURE OF LAMINATE FLOORING WE RECOMMEND THAT YOU PLACE A
SMALL PIECE OF HEAVY DUTY NON SLIP MATERIAL UNDER THE LEGS WHICH WILL
GIVE YOU THE FLEXIBILITY THAT THE ADJUSTERS NEED.
·WHEN MOVING THE BED IT IS ESSENTIAL THAT IT IS LIFTED INTO THE NEW POSITION.
NEVER DRAG THE BED AS THIS WILL MOVE THE LEGS FROM THE VERTICAL POSITION
THUS WEAKENING THE SUPPORT OF THE CENTRE RAIL.
·ADHERING TO THE RECOMMENDED PROCESS SHOULD ENSURE THAT YOUR BED GIVES
YOU YEARS OF TROUBLEFREE SERVICE.
·It is advisable to use approved cleaning products when cleaning our products as certain chemical
based cleaners could have an adverse effect on the bed finish.
Page 5 of 6

·All Limelight beds are produced to the highest standards and are packed
to avoid damage in transit, should you find that your new bed does not
meet with your satisfaction please contact Limelight customer care on
01455 850150.
·PLEASE NOTE: GOODS THAT NEED TO BE RETURNED
SHOULD BE SENT BACK IN ORIGINAL PACKAGING.
SHOULD YOU ENCOUNTER ANY DIFFICULTY WITH THE ASSEMBLY OF YOUR
BED,
PLEASE DO NOT TROUBLE YOUR RETAILER BUT
CALL, E-MAIL or WRITE to our
CUSTOMER SERVICES DEPARTSMENT
BETWEEN THE HOURS OF
9am to 5pm MONDAY to THURSDAY AND
9am to 4pm FRIDAY
Tel:-01455 850150
E-mail: - [email protected]
Limelight Beds Ltd
Orbital House
Arthur Street
Barwell
Leicestershire
LE9 8GZ
PROBLEMS?
Please have the following information ready for our staff:
Product name, part number & batch code
See our range on Web Site: - www.limelightbeds.co.uk
Page 6 of 6