LIMELIGHT Beds Rosa User manual

Page 1 of 6 ROSA 4'6" STORAGE BED
1. We suggest you spend a short time reading
through this leaflet and then follow the simple
step by step instructions.
2. If you follow the instructions carefully, the end
result should be worth the effort.
3. Do not discard any of the packaging until you
have checked that you have all the parts and
the pack of fittings.
4. This product is more stable when assembled
and placed on carpet.
5. To ensure an easier assembly, we strongly
advise that all fittings are only finger-tightened
during initial assembly phase. Only upon
completion of the assembly should all fixing
points be fully tightened.
6. We recommend a periodic check on all fixing
points to make sure they remain fully tightened.
7. Keep any fittings out of children's reach.
BEFORE YOU
START, HERE
IS SOME
HELPFUL
ADVICE :
Minimum No.
Of People
Recommended
To Assemble
This Product :
2
45
MINUTES
Approximate
Assembly
Time :
ASSEMBLY INSTRUCTIONS

Page 2 of 6 ROSA 4'6" STORAGE BED
PARTS AND HARDWARE LISTS
1
2
3
4
5
6
7
A
B
C
D
E
F
G
H
I
J
K
x1pc
Headboard
x1pc
Footboard
x2pcs
Siderail
x2pcs
Base Board
x2pcs
Central Leg
x28pcs
Flat Slat
M8x25mm
x1pc
x16pcs
x9pcs
x4pcs
x3pcs
x2pcs
x14pcs
x28pcs
x6pcs
x6pcs
x6pcs
M4x25mm
M6x45mm
Plastic Support
M8x40mm
x1pc
Gaslift Metal
Base

Page 3 of 6 ROSA 4'6" STORAGE BED
Attach the pre-fitted Gas Lift bar to the Siderail (3) brackets with pre-fitted bolt.
STEP 1
STEP 2
Place the plywood Base Boards (4)
into the bottom storage area.
STEP 3
3
A
D
B
1
2
A
D
B
3
C
3
3
Attach the Bracket (D) with Bolt (B) and slightly tighten with Allen Key (A). Mount both
Siderails (3) to Headboard (1) and Footboard (2) by pushing the Bracket (D) down to fit.
Do not fully tighten the screws at this moment.
4
Fix the Plastic Support (E) onto the
Siderails(3) and Footboard (2)
with Screws (C)
STEP 4
E
2

Page 4 of 6 ROSA 4'6" STORAGE BED
STEP 6
Fix the Central Legs(6) under the Gaslift Base (5) with Bolts (F)
STEP 5
Assemble the Gaslift Metal Frame onto the Gasslift bracket with Bolt (I), Washer (J) and
Hex Nut (K)
STEP 7
Assemble the Gaslift Metal Frame with Slats (7) and Plastic Caps (Gand H)
7
H
G
H
G
H
3
J
K
I
F
6
5

Page 6 of 6 ROSA 4'6" STORAGE BED
nPLEASE NOTE: GOODS THAT NEED TO BE RETURNED SHOULD
BE SENT BACK IN ITS ORIGINAL PACKAGING.
nWhen assembling your bed, please ensure that you have checked
the contents for all relevant parts.
nWhen tightening bolts, do make sure that they are fully tightened but
not forced.
nWhen moving your fully assembled bed, you must first remove the
mattress and lift the frame into position; taking care when lifting and
always have two people handling the bed. PLEASE DO NOT DRAG
THE BED as this will cause damage to the central support legs and
rail. Central legs MUST be in a vertical position at all times.
nDue to the nature of laminate flooring, we recommend that you place
non-slip material under the central support legs. This will stop the legs
from sliding on laminate/wooden floors and will prevent the bed from
collapsing.
nIt is advisable to use approved cleaning products when cleaning the
furniture and bed frame as certain chemical-based cleaners could
have an adverse effect on the bed's finish.
nAll Limelight beds are produced to the highest standards and are
packed to avoid damage in transit. Should you find that your new bed
does not meet your satisfaction, please contact Limelight's Customer
Services Department at 01455 850 150.
PRODUCT
CARING FOR YOUR NEW LIMELIGHT