Link Brand HDEXT1IR232 User manual

Type A (Receptacle) HDMI
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
Pin 10
Pin 11
Pin 12
Pin 13
Pin 14
Pin 15
Pin 16
Pin 17
Pin 18
Pin 19
TMDS Data2+
TMDS Data2 Shield
TMDS Data2–
TMDS Data1+
TMDS Data1 Shield
TMDS Data1–
TMDS Data0+
TMDS Data0 Shield
TMDS Data0–
TMDS Clock+
TMDS Clock Shield
TMDS Clock–
CEC
Reserved(N.C. on device)
SCL
SDA
DDC/CEC Ground
+5V Power
Hot Plug Detect
User Manual
Safety and Notice
T
he HDEXT1IR232 HDBasedT Lite Extender with Bi-direconal IR
& RS-232 has been tested for conformance to safety regulaons
and requirements, and has been cerfied for internaonal use.
However, like all electronic equipments, the HDEXT1IR232
should be used with care. Please read and follow the safety
instrucons to protect yourself from possible injury and to
minimize the risk of damage to the unit.
Connect a HDMI or DVI source (such as a Blu-ray Disc player) to the
transming unit HDEXT1IR232-TX.
Connect a HDMI or DVI display (such as a LCD TV) to the receiving
unit HDEXT1IR232-RX.
Connect IR Blaster/Receiver to both TX and RX units.
Connect a Cat-5/5e/6 cable between the transming and
receiving units.
Make sure this Cat-5/5e/6 cable is ghtly connected and not loose.
Plug in 5V DC power supply unit to the power jack of the receiving
unit HDEXT1IR232-RX and the transming unit HDEXT1IR232-TX.
Follow all instrucons and warnings marked on this unit.
Do not aempt to service this unit yourself, except where
explained in this manual.
Provide proper venlaon and air circulaon and do not use near
water.
Keep objects that might damage the device and assure that the
placement of this unit is on a stable surface.
Use only the power adapter and power cords and connecon
cables designed for this unit.
Do not use liquid or aerosol cleaners to clean this unit. Always
unplug the power to the device before cleaning.
HDMI PIN DEFINITION HARDWARE INSTALLATION
NOTICE
1.
2.
3.
4.
5.
6.
All HDMI over CAT5 transmission distances are measured using
Belden 1583A CAT5e 125MHz UTP cable and ASTRODESIGN Video
Signal Generator VG-859C & VG-870B.
Incorrect placement of IR Blaster and Receiver may result in the
failure of the IR extenders. Please check carefully before plugging in
the IR extender to the respecve IR sockets. Warranty will not cover
the damage.
The transmission length is largely affected by the type of Cat-5/5e/6
cables, the type of HDMI sources, and the type of HDMI display. The
tesng result shows solid UTP cables (usually in the form of 300m
[1,000] bulk cables) can transmit a lot longer signals than stranded
UTP cables (usually in the form of fixed length patch cords).
Shielded STP cables are beer suited than unshielded UTP cables. A
solid UTP Cat-5e cable shows longer transmission range than
stranded STP Cat-6 cable. For long extension applicaons, solid
UTP/STP cables are the only viable choice.
EIA/TIA-568-B terminaon (T568B) for Cat-5/5e/6 cables is
recommended for beer performance.
To reduce the interference among the unshielded twisted pairs of
wires in Cat-5/5e/6 cable, one can use shielded STP cables to
improve EMI problems, which is worsen in long transmission.
Because the quality of the CAT5/6 cables has the major effect on
how long the transmission limit can achieve and how good is the
received picture quality, the actual transmission range is subject to
one’s choice of Cat-5/5e/6 cables. For desired resoluons greater
than 1080i or 1280x1024, a Cat-6 cable is recommended.
If your HDMI display has mulple HDMI inputs, it is found that the
first HDMI input [HDMI input #1] generally can produce beer
transmission performance among all HDMI inputs.
1.
2.
3.
4.
5.
6.
7.
Performance Guide for HDMI over Category Cable Transmission
Performance rating
Type of category cable
Wiring
Shielding
CAT5
CAT5e
CAT6
Solid
Unshielded (UTP)



Shielded (STP)



Stranded
Unshielded (UTP)



Shielded (STP)



Termination Please use EIA/TIA-568-B termination (T568B) at any time
WARRANTY
The SELLER warrants the HDEXT1IR232 HDBasedT Lite Extender
with
Bi-direconal IR & RS-232 free from defects in the material and
workmanship for 1 year from the date of purchase from the SELLER or an
authorized dealer. Should this product fail to be in good working order
within 1 year warranty period, The SELLER, at its opon, repair or replace
the unit, provided that the unit has not been subjected to accident,
disaster, abuse or any unauthorized modificaons including stac
discharge and power surge. This warranty is offered by the SELLER for its
BUYER with direct transacon only. This warranty is void if the warranty
seal on the metal housing is broken.
Unit that fails under condions other than those covered will be
repaired at the current price of parts and labor in effect at the me of
repair. Such repairs are warranted for 90 days from the day of
reshipment to the BUYER. If the unit is delivered by mail, customers
agree to insure the unit or assume the risk of loss or damage in transit.
Under no circumstances will a unit be accepted without a return
authorizaon number.
The warranty is in lieu of all other warranes expressed or implied,
including without limitaons, any other implied warranty or fitness or
merchantability for any parcular purpose, all of which are expressly
disclaimed.
Proof of sale may be required in order to claim warranty.
Customers outside Taiwan are responsible for shipping charges to and
from the SELLER. Cables and power adapters are limited to a 30 day
warranty and must be free from any markings, scratches, and neatly
coiled.
The content of this manual has been carefully checked and is
believed to be accurate. However, The SELLER assumes no responsibility
for any inaccuracies that may be contained in this manual. The SELLER
will NOT be liable for direct, indirect, incidental, special, or consequenal
damages resulng from any defect or omission in this manual, even if
advised of the possibility of such damages. Also, the technical
informaon contained herein regarding the
HDEXT1IR232 features and
specificaons is subject to change without further noce.
The terms HDMI and HDMI High-Definion Mulmedia Interface,
and the HDMI logo are trademarks of HDMI Licensing LLC in the United
States and other countries.

Definition of IR Earphone Jack
The
HDEXT1IR232 HDBasedT Lite Extender with
Bi-direconal IR & RS-232 boosts up your video/audio transmission
distance up to 60m (198) in HDTV 1080p with 48-bit color depth.
HDEXT1IR232 also supports the most advanced 3D video format
complaint with HDMI specificaon and therefore guarantees the
highest 3D video compability on the market. With only one cost
effecve Cat.5/5e/6 cable, users can readily extend HDTV sources from
DVD players, Blu-ray Disc player, PS3, PC, and any other kinds of
sources compliant with TMDS to distant display monitors including
HDMI or DVI enabled TV sets or LCD PC monitors. With the advanced
design for the latest HDMI technology, deep color video, DTS-HD or
Dolby TrueHD audio, and HDCP supports and compability are all
further insured. This flexibility makes HDCP compliant DVD players or
PS3 transmit utmost high quality video and audio with a greater
distance at the minimal cost, when integrang several components
apart. In addion, HDEXT1IR232 is also equipped with bi-direconal IR
pass-through path and RS-232 serial port control. These bonus features
allow users to boost IR control distance up to 60m (198 ) and makes IR
control possible through only single Cat.5/5e/6 cable including HDMI
signals. In addion, serial port offers the convenient path for interacve
applicaon, such as touch panels.
The HDEXT1IR232 includes two units: transming unit
HDEXT1IR232-TX and receiving unit HDEXT1IR232-RX. The transming
unit is used to capture the input HDMI / DVI signals with IR control
packets and carry the signals via one cost effecve Cat.5/5e/6 cable.
The receiving unit is responsible for equalizing the transmied HDMI
signal and reconstrucng IR signals. HDEXT1IR232 offers the most
convenient soluon for digital signage with long distance A/V
transmission path, and with 10G transmission width ready,
HDEXT1IR232 is ready for your next HDMI generaon and applicaons!
Support HDMI Deep Color & full 3D & 4K2K@30 (HDBaseT-Lite
technology)
Extend the transmission up to 60m (198) from the HDMI source at
Full HD 1080p 48-bit and 40m (130) at 4K2K@30
HDCP & EDID Bypass
CEC support
Auto equalizaon
Pure unaltered uncompressed 7.1ch digital HDMI over Cat.5/5e/6
cable transmission
DTS-HD Master Audio and Dolby TrueHD high bit rate audio support
Support full frequency IR signal from 20KHz to 60KHz
Bi-direconal IR path-through
Full Duplex RS-232 control up to 115,200 bps through connector
Wall mounng housing design for easy and robust installaon
1x HDEXT1IR232
[TX&RX]
2x 5V DC power supply
1x User Manual
1x IR blaster
1x IR receiver
INTRODUCTION SPECIFICATIONS
FEATURES
PACKAGE CONTENTS
The length depends on the characteriscs and quality of the cables.
Higher resoluons and longer transmission distances require low
skew cables (<25ns/100m) for best performance. Unshielded CAT6
with metal RJ45 connectors is recommended.
IR PASS-THROUGH
IR Extenders
CONNECTION DIAGRAM
PANEL DESCRIPTIONS
Transmitting unit ► HDEXT1IR232-TX[RX]
RS-232: Connect to host/device serial port
with a DSUB-9 male-male cable here
Dip Switch: Setup the RS-232 mode for serial
communication channel
LED: TX/RX link indicator
RJ45: Plug in a Cat-5/5e/6 cable that needs
to be linked to the TX or RX.
IR ReceiverIR Blaster
IR ReceiverIR Blaster
IR Sockets
IR BLASTER: plug in the IR blaster to emit all IR command signals
received from the IR receiver from the other end to control the devices
corresponding to the IR signals.
IR RECEIVER: plug in the IR receiver to receive all IR command signals
from the IR remote controls of the corresponding devices.
!
Incorrect placement of IR Blaster and Receiver may result in the
failure of the IR extenders. Please check carefully before plugging in
the IR extender to the respecve IR sockets. Warranty will not cover
the damage.
You can buy any IR extension cables in the market that are
compable to the definion of the IR sockets for the matrix if
necessary for replacement use. However, IR cables longer than 2m
(6-) may not work.
1. IR Signal
2. Grounding
1. IR Signal[20-60 kHz]
2. Grounding
3. Power
i
i
[Receiving unit]
Model Name
HDEXT1IR232
Technical
HDEXT1IR232-TX
HDEXT1IR232-RX
Role of usage
Transmitter [TX]
Receiver [RX]
HDMI compliance
HDMI Deep Color, full 3D & 4K2K@30
HDCP compliance
Yes
Video bandwidth
Single-link 340MHz [10.2Gbps]
Video support
480i / 480p / 720p / 1080i / 1080p60
HDMI over UTP
1080p@60 60m (198ft) [CAT5e]
Audio support
Surround sound [up to 7.1ch) or stereo digital audio
Equalization
Auto
Input TMDS signal
1.2 Volts [peak-to-peak]
Input DDC signal
5 Volts [peak-to-peak, TTL]
ESD protection
[1] Human body model — ±19kV [air-gap discharge] & ±12kV [contact discharge]
[2] Core chipset — ±8kV
PCB stack-up
4-layer board [impedance control — differential 100Ω; single 50Ω]
IR pass-thru
Bi-directional
RS-232 support
Yes
Input
1x HDMI
1x 3.5mm
1x RJ-45[HDBaseT]
1x 3.5mm
Output
1x RJ-45[HDBaseT]
1x 3.5mm
1x HDMI
1x 3.5mm
HDMI source control
Controllable via IR pass-through from RX to TX with IR extenders
HDMI connector
Type A [19-pin female]
Min DIN connector
DIN-9
RJ-45 connector
WE/SS 8P8C(Reverse Mode)
Rotary control switch
None
3.5mm connector
IR receiver / IR blaster
IR receiver / IR blaster
Mechanical
Housing
Metal enclosure
Dimensions
[L x W x H]
Model
73 x 89 x 26mm [2.9" x 3.5" x 1"]
Package
175 x 125 x 216mm [6.8" x 4.9" x 8.5"]
Carton
647 x 366 x 237mm [2'1" x 1'2" x 9.3"]
Weight
Model
200g [7oz]
196g [6.9oz]
Package
900g [2 lbs]
Fixedness
Wall-mounting case with screws
Power supply
5V 2A DC
Power consumption
3 Watt [max]
7 Watt [max]
Operation
temperature
0~40°C [32~104°F]
Storage temperature
-20~60°C [-4~140°F]
Relative humidity
20~90% RH [no condensation]
Latch-locking power jack: Connect to 5V
DC power supply
LED: Power indicator
HDMI IN[OUT]: Connects to a HDMI
source[Display] with a HDMI male-male cable
IR Blaster: Infrared 3.5mm socket for
plugging in the extension cable of IR blaster
IR Receiver: Infrared 3.5mm socket for
plugging in the extension cable of IR receiver
DIP Switch Position
Description
TX& RX
PIN#1
ON [](DTE)
TxD: The 2nd pin of RS-232, which is in charge of sending data
RxD: The 3
rd
pin of RS-232, which is in charge of receiving data
OFF [](DCE)
TxD: The 3rd pin of RS-232, which is in charge of sending data
RxD: The 2
nd
pin of RS-232, which is in charge of receiving data
PIN#2
ON []
Firmware Update
OFF []
Normal
HDEXT1IR232-TX HDEXT1IR232-RX