SC&T HE04SEK User manual

1
HDMI Distribution Amplifier CAT5e Extender
ITEM NO.: HE04SEK 1 x 4 Economic Distribution Amplifier CAT5e Extender Kit
HE04SEK extends and distributes HDMI signal to 4 remotes HDMI displays over CAT5e cable.
There is no power required for the receiver (HE01SER).
The transmission distance is up to 40M at 1080p, 70M at 720p.
It is expandable by stacking to another HE04SET or working with chainable receiver HE01SLR to get 1 in
multiple out application. (1 in 5 out, 1 in 6 out, 1 in 8 out…etc.)
It’s suitable for any place where one in multiple out application is needed, such as bar, business, church,
conference room, school, CCTV, surveillance…etc.
Features:
 Extends and distributes HDMI signal to 4 remote HDMI displays over CAT5e cable.
 Receiver unit no external power required.
 Supports resolution up to 1080p 60Hz.
 Transmission distance up to 40M at 1080p, 70M at 720p.
 Built-in HDMI loop out supports CEC.
 The transmitter can be stacked to another HE04SET for 1 in 8 out application.
 HDMI 1.4 compliance.
 Supports AC3, DTS, Dobly TrueHD, DTS-HD
 Supports RS232 control.
 Supports EDID management
 Optional Model: HE01SLR (Chainable Receiver)
Installation:
(1) Extends and distributes 1 HDMI source to remote 4 HDMI displays.

2
(2) Works with chainable receiver HE01SLR (Max. 3pcs) to get extra transmission distance and outputs.
(3)Stack to another HE04SET through HDMI loop out port to get configuration of 1 in 8 out.

3
Panel Review:
(1) HE04SET
No. Interface Description
1 Green LED Green light indicates “ON” status.
2 Blue LED Blue light indicates “HDMI IN” is connected to HDMI source.
3 Blue LED Blue light indicates “LOOPOUT” is connected to HDMI display.
4 Rotary Switch To select EDID by rotating the switch from 0 to F. (please refer to EDID setting)
5 SET Button Press 1 second to copy selected EDID.
6 Output 1~4 Connects to remote receivers (HE01SER, HE01SLR) with CAT5e cables.
(please refer to Note 2-4)
7 HDMI Input Connects to HDMI source with HDMI cable.
8 Loop Out Connects to HDMI display or another HE04SET with HDMI cable.
(please refer to Note 1)
9 Console Connects to RS232 control device with DB9(F) cable for controlling
HE04SET or updating firmware. (please refer to RS232 setting)
10 Power Input Connects to DC12V 1A adapter.
(2) HE01SER
No. Interface Description
1 Green LED Green light indicates receiving power and video signals.
2 Yellow LED Yellow light indicates no signal input or receiving an unsupported format.

4
Notes:
1. When connect HDMI display with loop out port, please make sure HDMI cable connects to the
Input 1 of HDMI display.
2. It is recommended using UTP cable.
3. When using the STP cable, the transmission distance might be shorter. (CAT6a: 25-30M,
CAT7:25- 40M)
4. The cable must be straight, do not roll the cable to avoid crosstalk interference.
RJ45 Pinout
(PIN TIA/EIA-568B)
RS232 Wiring
Hyper Terminal setting:〔57600bps (8-N-1)〕
Note: Pins not shown in table have no connection
RS232 Command Table
Command Description
OFF 1(Enter) OUTPUT 1 OFF
OFF 2(Enter) OUTPUT 2 OFF
OFF 3(Enter) OUTPUT 3 OFF
OFF 4(Enter) OUTPUT 4 OFF
OFF 5(Enter) HDMI LOOPOUT OFF
ON 1(Enter) OUTPUT 1 ON
ON 2(Enter) OUTPUT 2 ON
ON 3(Enter) OUTPUT 3 ON
ON 4(Enter) OUTPUT 4 ON
ON 5(Enter) HDMI LOOPOUT ON
(PIN TIA/EIA-568B)
PIN Wire Color
1 Orange-white
2 Orange
3 Green-white
4 Blue
5 Blue-white
6 Green
7 Brown-white
8 Brown
RS232
Pin Definition
2 TX
3 RX
5 GND

5
EDID Table
Number EDID Number EDID
0 Customize EDID #1 81920x1080
1 Customize EDID #2 91920x1200
2 1024x768 A720p 50Hz LPCM 2CH
3 1280x720 B720p 60Hz LPCM 2CH
4 1280x1024 C1080p 50Hz LPCM 2CH
5 1366x768 D1080p 60Hz LPCM 2CH
6 1600x900 E1080p 50Hz MULTI
7 1680x1050 F1080p 60Hz MULTI
EDID Settings
Step1: Refer to EDID list at last page and find the number of which EDID is needed. (0~F)
Step2: Rotate the rotary dip switch arrow to the selected number.
Step3: Click “SET” button, and the two blue LEDs will flash quickly.
Step4: Wait for HE04SET to restart, and the process of EDID setting is done.
Customize EDID Settings
Step1: Connects display and loop out port through HDMI cable.
Step2: Press and Hold “SET” button for approximately 3 second, and the two blue LEDs will flash
slowly then quickly.
Step3: Wait for HE04SET to restart, and the process of copying EDID is done.
Caution:
1. The wiring must be away from any equipment with electromagnetic wave, i.e.: mobile phone,
microwave, radio equipment, fluorescent lamp, high voltage power lines.
2. HE04SEK isn’t networking device, please do not connect with Ethernet device to avoid
damages.
Package Contents:
1 x HE04SET
4 x HE01SER
1 x DC12V 1A power supply
4 x Rubber cushions
2 x Screws/ Screw hole plugs

6
Specification:
ITEM NO. HE04SET
Input Interface HDMI Type A x 1
Loopout Interface HDMI Type A x 1
Video Output Interface RJ45x4
Resolution Up to 1080p @ 60Hz
Transmission distance Up to 40M at 1080p, 70M at 720p
RS232 Interface DB9(F)
RS232 Baud Rate 57600 bps
Power Supply DC 12V 1A
Max. Power Consumption 96W (0.8A)
Temperature Operation: 0 to 70℃, Storage: -20 to 125℃, Humidity: up to 95%
Dimension (mm) 167 x 101 x 40
Weight (g) 460
ITEM NO. HE01SE
R
Resolution Up to 1080p @ 60Hz
Distance Up to 40M at 1080p, 70M at 720p
HDMI Connector Type A
Power Consumption 320mA
Temperature Operation: 0 to 55℃, Storage: -20 to 85℃, Humidity: up to 95%
Dimension (mm) 57.5 × 24 × 20.2
Weight (g) 20
Rev. A