Linksys EG1032 User manual

Instant Gigabit Series
Instant Gigabit
Network Adapter
Use this Guide to install the following products:
EG1032 (32-bit PCI Card)
EG1064 (64-bit PCI Card)
User Guide

COPYRIGHT & TRADEMARKS
Copyright © 2001 Linksys, All Rights Reserved. Instant Gigabit is a trademark of
Linksys. Microsoft, Windows, and the Windows logo are registered trademarks of
Microsoft Corporation. All other trademarks and brand names are the property of their
respective proprietors.
LIMITED WARRANTY
Linksys guarantees that every Instant Gigabit Network Adapter is free from physical
defects in material and workmanship under normal use for the lifetime of the card. If the
product proves defective during this warranty period, call Linksys Customer Support in
order to obtain a Return Authorization number. BE SURE TO HAVE YOUR PROOF OF
PURCHASE AND A BARCODE FROM THE PRODUCT'S PACKAGING ON HAND WHEN
CALLING. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PUR-
CHASE. When returning a product, mark the Return Authorization Number clearly on the
outside of the package and include your original proof of purchase. All customers locat-
ed outside of the United States of America and Canada shall be held responsible for
shipping and handling charges.
IN NO EVENT SHALL LINKSYS’ LIABILITY EXCEED THE PRICE PAID FOR THE PROD-
UCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAM-
AGES RESULTING FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFT-
WARE, OR ITS DOCUMENTATION. Linksys makes no warranty or representation,
expressed, implied, or statutory, with respect to its products or the contents or use of this
documentation and all accompanying software, and specifically disclaims its quality,
performance, merchantability, or fitness for any particular purpose. Linksys reserves the
right to revise or update its products, software, or documentation without obligation to
notify any individual or entity. Please direct all inquiries to:
Linksys P.O. Box 18558, Irvine, CA 92623.
FCC STATEMENT
The Instant Gigabit Network Adapter has been tested and found to comply with the lim-
its for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used according to the instructions, may cause harmful interfer-
ence to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which is found by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment or device
• Connect the equipment to an outlet other than the receiver’s
• Consult a dealer or an experienced radio/TV technician for assistance
UG-EG1032_64-10129 DG

Table of Contents
Introduction 1
The Linksys Instant Gigabit Network Adapter 1
Features 1
Package Contents for the EG1064 Adapter 2
Package Contents for the EG1032 Adapter 2
System Requirements for the PCI Adapter 2
Getting to Know the Instant Gigabit Network
Adapter 3
The LEDs 3
The RJ-45 Port 3
Installing the Instant Gigabit Network Adapter 4
Overview 4
Installing the Instant Gigabit Network Adapter 4
Installing the Drivers for Windows 95 6
Overview 6
Installing the Network Adapter’s Driver 7
Installing the Drivers for Windows 98 10
Overview 10
Installing the Network Adapter’s Driver 10
Installing the Drivers for Windows Millennium 14
Overview 14
Installing the Network Adapter’s Driver 14
Windows NT 4.0 Installation and Setup 18
Overview 18
Installing NT Networking and the Network Adapter Driver 19
Installing the Network Adapter Driver if Networking is Already Installed 25
Windows 2000 Installation and Setup 29
Overview 29
Installing the Network Adapter’s Driver 29
Advanced Properties 33
Overview 33
Configuring the Instant Gigabit Network Adapter 35
Configuring the Adapter for Windows 95, 98, and Millennium 35
Appendix 40
Sharing Your Files and Printers 40
Installing the Driver in Windows 95 Version A 42
Novell Netware 3.x Client Setup forWindows 95,98,or Millennium 43
Starting Over in Windows 95, 98 or Millennium 44
Starting Over in Windows 2000 48
Manually Installing the Network Components in 51
Windows 95,98, or Millennium
Installing and Configuring Wake-On-LAN 53
About Plug-and-Play PCI Technology 53
Linux, Open Source and Beta Operating Systems 55
Twisted Pair Cabling 55
Troubleshooting 56
Glossary 60
Specifications 68
Specifications for EG1032 68
Specifications for EG1064 69
Environmental for EG1032 70
Environmental for EG1064 70
Warranty Information 71
Contact Information 72
Instant Gigabit Network Adapter (EG1032/EG1064)
Instant Gigabit Series

• One Instant Gigabit®Network Adapter
• One Instant Gigabit®Network Adapter
• One Driver Disk
• One User Guide and Registration Card
• One Instant Gigabit®Network Adapter
• One Driver Disk
• One User Guide and Registration Card
• Pentium 90 or Faster
• Minimum 16MB of RAM
• PCI Local Bus 2.1 compliant
• Windows 95 (or higher) Operating System
Introduction
The Linksys Instant Gigabit Network Adapter
Unprecedented speed is now available over your existing network cabling!
Built to run the fastest video, publishing, and database network applications,
the Instant Gigabit Network Adapter is a high performance network adapter for
32 or 64-bit PCI-equipped local bus computers. Boasting an incredible maxi-
mum data throughput of 2000 megabits-per-second in full duplex mode, it
includes a 10BaseT/100BaseTX/1000Base-T port, which means that you can
begin integrating Gigabit now—even if you don't plan on upgrading to a
1000Mbps network right away.
The Instant Gigabit Network Adapter is Windows Plug-and-Play compatible.
The card also runs on virtually all major operating systems. Wake-On-LAN
support is built in—you can wake up your workstations from anywhere on the
network! Built-in support for the widest range of PCI motherboards, network-
ing hardware, and software means you don't have to worry about compatibili-
ty.
• Easy to Use Plug-and-Play 10/100/1000 PCI Network Card
• Full Duplex Capability at Speeds Up To 2000Mbps
• Connects to 10Mbps, 100Mbps, and Gigabit Ethernet Networks
• Power On Your PC From Anywhere on the Network with Wake-On-Lan
Management
• Works With Virutually All Major Operating Systems
• High-Speed Performance
• Automatically Adjusts to Full or Half Duplex at 10/100/1000 Mbps
• Wake-On-LAN and Plug-and-Play Compatible
• Runs with Virtually All Major Operating Systems
• Bus Mastering 64-bit Architecture Supports Gigabit Speeds
• Diagnostic LEDs For Easy Troubleshooting
• Easy to Install and Use
• IEEE 802.3x Flow Control Supported
• IEEE 802.1Q Priority Queuing Supported
• Supports 66 Mhz, 64-bit PCI v2.2
• Internal 8Kb Transfer and 32Kb Receive Data FIFOs
• FreeTechnical Support - 24 Hours a Day, 7 Days a Week for North America
Only
• One Year Limited Warranty
Features
The Linksys Instant Gigabit Network Adapter
Package Contents for the EG1032 Adapter
System Requirements for the PCI Adapter
Package Contents for the EG1064 Adapter
Instant Gigabit Network Adapter (EG1032/EG1064)
Instant Gigabit Series
2
1

Installing the Instant Gigabit
Network Adapter
Each Instant Gigabit Network Adapter is equipped with an RJ-45 port that
automatically adjusts to either 10Mbps, 100Mbps, or 1000Mbps speeds, allow-
ing your PC to attach to either Gigabit Ethernet, Fast Ethernet, or regular
Ethernet network segments without additional hardware or software.
The card should only be used with twisted-pair cabling, such as 10BaseT,
100BaseTX, or 1000Base-T cabling. For best results, we recommend using
Category 5e or better unshielded twisted-pair cabling although category 3 can
be used for 10BaseT segments. The cable that runs from your PC’s Instant
Gigabit Network Adapter card to your network should not exceed 100 meters
(328 feet).
Each Instant Gigabit Network Adapter is equipped with an RJ-45 port that
automatically adjusts to either 10Mbps, 100Mbps, or 1000Mbps speeds, allow-
ing your PC to attach to either Gigabit Ethernet, Fast Ethernet, or regular
Ethernet network segments without additional hardware or software.
The card should only be used with twisted-pair cabling, such as 10BaseT,
100BaseTX, or 1000Base-T cabling. For best results, we recommend using
Category 5e or better unshielded twisted-pair cabling although category 3 can
be used for 10BaseT segments. Only Category 5e or better cable will work
for Gigabit transfer. In any case, the cable that runs from your PC’s Instant
Gigabit Network Adapter card to your network should not exceed 100 meters
(328 feet).
Installing the Network Card & Cabling
1. Power off your PC and any peripheral equipment attached to it. Unplug
your PC’s power cord. For suggestions on choosing the PC in which to
install the Adapter, see the section called PlanningYour Network.
2. Remove your computer's outside cover.
Overview
Installing the Instant Gigabit Network Adapter
Instant Gigabit Network Adapter (EG1032/EG1064)
4
Getting to Know the Instant
Gigabit Network Adapter
LEDs
Link/Act The Link LED will illuminate when the card has been successfully
connected to a network and flicker when there is network activity.
1000 The 1000 LED will illuminate when the card is operating at
1000Mbps. If the 1000 LED is not illuminated and the PC is pow-
ered on, the card will have automatically determined that your net-
work is operating at a slower speed and compensate accordingly.
The RJ-45 Port
The RJ-45 Port is where you will connect your network cabling.
The LEDs
The RJ-45 Port
Instant Gigabit Series
Getting to Know the Instant
Gigabit Network Adapter
3

Installing the Drivers for
Windows 95
After installing the Instant Gigabit Network
Adapter in your computer, follow these
instructions for installing the network driv-
er. The installation procedure for the net-
work driver will vary slightly depending on
the version of Windows 95 you are using
and your current system configuration. For
troubleshooting tips during setup, refer to
the Troubleshooting section.
There are different versions of Windows 95:
• VersionA
• Version B (also known as OSR2)
The installation procedure for the network driver will vary slightly depending
on which version of Windows 95 you are using.To begin the driver installation,
and to determine which version of Windows 95 you are using:
1. Start up your PC.
2. Windows 95 will automatically detect the Network Adapter in your com-
puter. If the Update Device DriverWizard window appears (see next page),
you are using Windows 95 version B. If a window other than this appears,
you are using Windows 95 version A. For Windows 95 version A driver
installation, refer to the Appendix.
NNoottee::During the installa-
tion, Windows 95 may ask
you for a ccoommppuutteerroorrwwoorrkk--
ggrroouuppnnaammee. If so, turn to
step eight in NNeettwwoorrkk
CCoommppoonneennttCCoonnffiigguurraattiioonn.
Once you have established
your computer and work-
group names, go back to
where you left off and con-
tinue with the installation.
Overview
Instant Gigabit Network Adapter (EG1032/EG1064)
6
Instant Gigabit Series
3. Open your computer and locate the PCI slot(s) on your motherboard. PCI
slots are easily identified by their beige or white color, and by the fact that
network cards fit snugly into them. Remove the metal slot cover on the
back of the PC, then insert the Instant Gigabit Network Adapter into any
available PCI card slot.
4. If you are interested inWake-On-LAN, refer to theAppendix for instruc-
tions on Wake-on-Lan installation. Wake-On-LAN can be installed at any
time, so there is no need to do it now.
5. Once your Instant Gigabit Network Adapter is firmly in place, secure
its fastening tab to your PC's chassis with a mounting screw.
6. Replace your PC's cover.
7. Connect one end of the twisted-pair cable to your PC at the Instant
Gigabit Network Adapter’s RJ-45 port.
8. Plug the other end of the cable into your network’s Gigabit hub or switch
port.
9. Reconnect your PC’s power, then power on your computer. Your comput-
er will automatically recognize the card and assign it a unique IRQ ("inter-
rupt") and I/O address.
The card installation is complete. Next, you must configure your PC’s
operating system to work with the Instant Gigabit Network Adapter.
Turn to the appropriate section for your PC’s operating system for driver
installation instructions.
5

3. If you clicked the Other Locations button, this window will appear. Enter
a:\win95. Windows will begin copying the Network Adapter’s driver files
to your PC.
4. Once Windows has located the drivers, the following window will appear.
To use this driver, click the Finish button.
At this point, the installation may require files from your Windows 95 CD-
ROM. If prompted, insert your Windows 95 CD-ROM into your CD-ROM
drive and enter d:\win95 in the box that appears (where “d” is the letter of
your CD-ROM drive). If you were not supplied with a Windows 95 CD-
ROM, your Windows files may have been placed on your hard drive by
your computer manufacturer. While the location of these files may vary ,
many manufacturers use c:\windows\options\cabs as the path. Try enter-
ing this path into the box. If no files are found, check your computer’s doc-
umentation or contact your computer manufacturer for more information.
Instant Gigabit Network Adapter (EG1032/EG1064)
87
1. While the Update Device DriverWizard window is visible, insert the Instant
Gigabit NetworkAdapter Driver Disk into your floppy drive and click the
Next button.
2. Windows 95 will find the Linksys EG1032/EG1064 Instant Gigabit Network
Adapter driver on the disk. Click the Next button to continue. If Windows
fails to find the driver, click the Other Locations button to browse for the
driver.
Installing the Network Adapter’s Driver
Instant Gigabit Series

Installing the Drivers for
Windows 98
Overview
After physically installing the Instant Gigabit Network Adapter in your com-
puter, follow these instructions to install the network driver. The installation
procedure for the network driver will vary slightly depending on which version
of Windows 98 you are using, and on your current system configuration. If at
any time during the installation you encounter problems, consult the
Troubleshooting section.
Installing the Network Card’s Driver
1. If you haven’t already, start up your computer.
2. Windows 98 will automatically detect the presence of the PCI Ethernet
Controller hardware in your computer.
3. Insert the Instant Gigabit Network Adapter Driver Disk into your floppy
drive while the Add New Hardware Wizard window is visible. Click Next.
Installing the Network Adapter’s Driver
Overview
Instant Gigabit Network Adapter (EG1032/EG1064)
109
5. Once the driver is installed, the following screen will appear. The default
settings should allow the Adapter to function properly. Click the OK but-
ton to continue. For more information about these settings, refer to the
Advanced Settings section of this manual.
6. When asked if you want to restart your PC, remove all disks from your
computer’s drives and click the Yes button. If Windows does not ask you
to restart your PC, click the Start button, choose Shut Down, choose
Restart, then click Yes.
TheWindows 95Version B driver installation is complete. Refer to the sec-
tion on Configuring the Instant Gigabit NetworkAdapter forWindows 95,98,
and Millennium for more information about the setup of theAdapter.
NNoottee::From this point on, you must provide Windows with a User
name and Password every time you are prompted to do so.
Remember to click OOKKto properly log into Windows. If you click
CCaanncceellor hitthe EEssccaappee((EESSCC))key,youwillnot logintothe network.
Instant Gigabit Series

6. A window will open saying that Windows is now ready to install the Linksys
EG1032/EG1064 Instant Gigabit Network Adapter driver. Click Next.
7. Windows will begin copying the Instant Gigabit Network Adapter’s driver
files to your PC.
At this point, the installation may require files from your Windows 98 CD-
ROM. If prompted, insert your Windows 98 CD-ROM into your CD-ROM
drive and enter d:\win98 in the box that appears (where “d” is the letter of
your CD-ROM drive). If you were not supplied with a Windows 98 CD-
ROM, your Windows files may have been placed on your hard drive by
your computer manufacturer. While the location of these files may vary ,
many manufacturers use c:\windows\options\cabs as the path. Try enter-
ing this path into the box. If no files are found, check your computer’s doc-
umentation or contact your computer manufacturer for more information.
Instant Gigabit Network Adapter (EG1032/EG1064)
1211
4. Select Search for the best driver for your device (Recommended). Click
Next.
5. Select Specify a location and enter a:\win98 in the drop down box. Click
Next to continue.
NNoottee::Windows 98 may ask you for a ccoommppuutteerroorrwwoorrkkggrroouupp
nnaammee. If so, see the next section, NNeettwwoorrkkCCoommppoonneenntt
CCoonnffiigguurraattiioonn. Once you have established your computer and
workgroup names, return to where you left off and continue with
the installation.
Instant Gigabit Series

Installing the Drivers for
Windows Millennium
After physically installing the Instant Gigabit Network Adapter in your com-
puter, follow these instructions to install the network driver. The installation
procedure for the network driver will depend on your current system configu-
ration. If at any time during the installation you encounter problems, consult the
Troubleshooting section.
Installing the Network Card’s Driver
1. If you haven’t already, start up your computer.
2. Windows Millennium will automatically detect the presence of the PCI
Ethernet Controller hardware in your computer.
3. Insert the Instant Gigabit Network Adapter Driver Disk into your floppy
drive while the Add New HardwareWizard window is visible. Select Specify
the location of the driver (Advanced) option. Click Next.
Overview
Installing the Network Adapter’s Driver
Instant Gigabit Network Adapter (EG1032/EG1064)
1413
8. Once the driver is
installed, the following
screen will appear.
The default settings
should allow the
Adapter to function
properly. Click the
OK button to continue.
For more information
about these settings,
refer to the Advanced
Settings section of this
manual.
9. When asked if you want to restart your PC, remove all disks and click Yes.
If Windows does not ask you to restart your PC, click the Start button,
choose Shut Down, choose Restart, then click Yes.
The Windows 98 driver installation is complete. Refer to the section on
Configuring the Instant Gigabit NetworkAdapter forWindows 95, 98, and
Millennium for more information about the setup of theAdapter.
NNoottee::From this point on, you must provide Windows with a
User name and Password every time you are prompted to
do so. Remember to click OOKKto properly log into Windows.
If you click CCaanncceellor hit the EEssccaappee((EESSCC))key, you will not
log into the network.
Instant Gigabit Series

6. At this point, the installation may require files from your Windows
Millennium CD-ROM. If prompted, insert your Windows Millennium CD-
ROM into your CD-ROM drive and enter d:\win9x in the box that appears
(where “d” is the letter of your CD-ROM drive). If you were not supplied
with a Windows Millennium CD-ROM, your Windows files may have been
placed on your hard drive by your computer manufacturer. While the loca-
tion of these files may vary , many manufacturers use
c:\windows\options\cabs as the path. Try entering this path into the box. If
no files are found, check your computer’s documentation or contact your
computer manufacturer for more information.
7. Once the driver is installed, the following screen will appear. The default
settings should allow the Adapter to function properly. Click the OK button
to continue. For more information about these settings, refer to the
Advanced Settings section of this manual.
Instant Gigabit Network Adapter (EG1032/EG1064)
16
4. Make sure that Search for the best driver for your device
(Recommended) is selected. Check the Specify a location option and
enter A:\WINME in the drop down box. Click Next.
5. Once the driver has been located, the following screen will appear. Click the
Next button.
Instant Gigabit Series
15

Windows NT 4.0 Installation &
Setup
The following instructions will set up the Instant Gigabit NetworkAdapter in a
computer running NT 4.0 server/workstation. You should have your original
Windows NT CD-ROM available during the installation, as you might be asked
to supply it. Always contact your network administrator or consult your NT
documentation if you have questions.
To install the network driver for an NT 4.0 Server or Workstation
1. Log into Windows NT as an administrator (or as a user with administra-
tive rights) .
2. Click on Start, Settings, Control Panel, and then double-click on the
Network icon.
3. If you have not previously installed Windows NT networking on your com-
puter, a message will appear that reads: Windows NT Networking is not
installed. Do you want to install it now?
• If you see this message, click Yes to install NT networking along with the
Instant Gigabit Network Adapter's network driver, and continue to the next
section.
• If you don't see this message, NT networking is already installed and you
should turn to the Installing the Instant Gigabit Network Adapter
Driver if Networking isAlready Installed section.
Overview
Instant Gigabit Network Adapter (EG1032/EG1064)
18
8. The following screen will appear next, indicating that the drivers have been
installed successfully. Click the Finish button.
9. When asked if you want to restart your PC, remove all disks and click Yes.
If Windows does not ask you to restart your PC, click the Start button,
choose Shut Down, choose Restart, then click Yes.
The Windows Millennium driver installation is complete. Refer to the sec-
tion on Configuring the Instant Gigabit NetworkAdapter forWindows 95,98,
and Millennium for more information about the setup of theAdapter.
NNoottee::From this point on, you must provide Windows with a
User name and Password every time you are prompted to
do so. Remember to click OOKKto properly log into Windows.
If you click CCaanncceellor hit the EEssccaappee((EESSCC))key, you will not
log into the network.
Instant Gigabit Series
17

5. Highlight the Linksys EG1032/EG1064 Instant Gigabit Network
Adapter entry in the window that appears. Click OK.
6. The adapter will be added to the list of installed Network Adapters. Click
Next.
Instant Gigabit Network Adapter (EG1032/EG1064)
20
1. After clicking on Yes, the Network Setup Wizard window will appear.
2. Put a checkmark next to the Wired to the network option. Click Next.
3. Click on the Select from list... button to select a network adapter.
4. Click on the Have Disk button. Insert the Instant Gigabit Network Adapter
Driver Disk into drive A. Type a:\ into the box on your screen and click
OK.
Installing NT Networking and the Network Adapter Driver
Instant Gigabit Series
19

9. NT will probably ask you to supply your original Windows NT CD-ROM
or setup disks. If so, place your Windows NT CD-ROM in your CD drive.
If the CD-ROM loads a pop-up window, close it. Type D:\i386 (or the
appropriate CD-ROM drive letter) in the box and click Continue.
10. NT will ask you to choose a media type for the Instant Gigabit Network
Adapter. Choose AutoSense. You can change these settings later if need-
ed. When finished, click OK.
Instant Gigabit Network Adapter (EG1032/EG1064)
22
7. Place check marks beside each listed network protocol that you wish to
install. See your Microsoft Windows NT user guide or talk to your network
administrator for more information about network protocols. When you're
finished, click Next.
8. A list of services will appear. Click Next to approve these services, fol-
lowed by Next again.
NNoottee::If you install the TTCCPP//IIPPpprroottooccooll, refer to your system adminis-
trator or your Windows NT documentation when installation steps that
aren’t listed in this User Guide appear. Linksys does not provide tech-
nical support for the configuration or troubleshooting of the TCP/IP
protocol.
Instant Gigabit Series
21

13. Click Finish. When asked if you want to restart your computer, remove the
Driver Disk and click Yes.
14. Once your PC has rebooted and you are logged in, double-click the
Network Neighborhood icon on your desktop. Ensure that you have
access to the network. If you do, your card has been properly installed.
• If you had previously installed a NT service pack, you must re-install that
now.
• If you need to install the TCP/IP protocol, refer to your system administra-
tor or your Windows NT documentation. Linksys does not provide techni-
cal support for the configuration or troubleshooting of the TCP/IP proto-
col
The Windows NT Installation and Setup of the Instant Gigabit Network
Adapter is complete. Do not continue on with the next set of instructions.
They are for NT users who already have their networking configured.
NNoottee::For information and help on choosing your bind-
ings, services and protocols, ask your network admin-
istrator, or check your Windows NT documentation.
NNoottee: If you had previously installed an NT service pack,
you must reinstall it now.Otherwise, you may receive Not
Enough Service Storage Space errors in the Event
Viewer.
Instant Gigabit Network Adapter (EG1032/EG1064)
24
11. NT will copy the necessary network
drivers to your PC. When the copying
is complete, you will see a list of
installed bindings. Change the bind-
ings settings if needed and click Next.
Click Next again.
12. Choose either Workgroup or Domain, depending on the type of network
you're setting up. (Your Microsoft documentation explains the difference
between Workgroups and Domains.) Click Next.
NNoottee::For information and
help on choosing your bind-
ings, services and protocols,
ask your network administra-
tor, or check your Windows
NT documentation.
Instant Gigabit Series
23

3. When the list of available network adapters appears, click the Have Disk but-
ton.
4. Put the Instant Gigabit Network Adapter disk into drive A. Type a:\ into the
box on your screen and click OK.
NNoottee::If you install the TTCCPP//IIPPpprroottooccooll, refer to your system admin-
istrator or your Windows NT documentation when installation steps
that aren’t listed in this User Guide appear. Linksys does not provide
technical support for the configuration or troubleshooting of the
TCP/IP protocol.
Instant Gigabit Network Adapter (EG1032/EG1064)
26
Installing the Instant GigabiMNetwork Adapter if
Networking is Already Installed
The following steps will install the Instant Gigabit Network Adapter’s driver
software on your PC, enabling your PC to properly communicate with the card.
Remember that you must be logged on as a network administrator (or as a
user with administrative rights) to continue.
1. Click on Start, Settings, Control Panel, then double-click on the Network
icon.
2. When the networking window appears, choose the Adapters tab. Click the
Add button.
Installing the Network Adapter if Networking is Already
Installed
Instant Gigabit Series
25

8. Click on the Protocols tab. Add any protocols you require by clicking the
Add button. (Refer to your Microsoft documentation if you have any ques-
tions on adding protocols.)
9. After your bindings, settings, and services are set, click the Close button.
10. Remove your Driver Disk and CD-ROM and click Yes to restart your PC.
11. Once your PC has rebooted, double-click the Network Neighborhood icon
on your desktop. Ensure that you have access to the network. If you do,
your card has been properly installed.
• If you had previously installed a NT service pack, you must re-install that
now. Otherwise, you may receive Not Enough Service Storage Space errors
in the Event Viewer.
• If you need to install the TCP/IP protocol, refer to your system administra-
tor or your Windows NT documentation. Linksys does not provide techni-
cal support for the configuration or troubleshooting of the TCP/IP proto-
col
The Windows NT Installation and Setup of the Instant Gigabit Network
Adapter is complete
NNoottee: If you had previously installed an
NT service pack, you must reinstall it
now.Otherwise, you may receive Not
Enough Service Storage Space errors
in the Event Viewer.
Instant Gigabit Network Adapter (EG1032/EG1064)
28
5. Highlight the Linksys EG1032/EG1064 Instant Gigabit NetworkAdapter
entry in the window that appears. Click OK.
6. Windows NT then asks you for the media type. Choose the AutoSense
option. When finished, click on OK. Click Close.
7. NT will probably ask you to supply your original Windows NT CD-ROM or
setup disks. Direct Windows NT to the proper location (most likely
D:\i386).
Instant Gigabit Series
27

3. Windows will display the Welcome to the Found New Hardware Wizard
box. Click Next.
4. The Install Hardware Device Drivers dialog box will appear. When
Ethernet Controller is displayed, select “Search for a suitable driver for my
device (Recommended)”. Click Next.
Instant Gigabit Network Adapter (EG1032/EG1064)
30
Windows 2000 Installation and
Setup
Overview
After physically installing the Instant
Gigabit Network Adapter in your comput-
er, follow these instructions to install the
network driver. The installation procedure
for the network driver will vary slightly
depending on which version of Windows
2000 you are using, and on your current
system configuration. If at any time during
the installation you encounter problems,
consult the Troubleshooting section.
Installing the Driver in Windows 2000
After physically installing the Instant Gigabit Network Adapter in your com-
puter, follow these instructions to install the network driver.
1. Start your computer if you haven’t already done so, and boot Windows
2000. Log in if you are asked to. You must have administrative rights to
complete this installation.
2. The Found New Hardware window will appear, indicating that Windows
has found the Adapter.
NNoottee::Prior to pro-
ceeding, ensure
that you are oper-
ating Windows
2000 with administrative
rights. If you log into Windows
2000 without administrative
rights, you may run into prob-
lems during the installation.
Overview
Installing the Network Adapter’s Drivers
Instant Gigabit Series
29

6. The Driver File Search Results dialog box will appear. Click Next.
7. The Completing the Found New Hardware Wizard dialog box will
appear. The following adapter name will be shown: Linksys
EG1032/EG1064 Instant Gigabit Network Adapter. Click Finish.
8. Remove the driver disk from the floppy drive.
The Windows 2000 driver installation is complete. If you want to share
files or printers, refer to your Windows 2000 documentation or check
with your system administrator.
Instant Gigabit Network Adapter (EG1032/EG1064)
32
5. The Locate Driver Files dialog box will appear. Select “Specify a loca-
tion”. Click Next.
6. When the Found New Hardware Wizard box appears, insert the Linksys
Instant Gigabit Network Adapter Driver Disk into your floppy drive. In the
“Copy manufacturer’s files from” field, type “A:\Win2000”. Click OK.
Instant Gigabit Series
31

NetworkAddress:
Allows the user to configure the network address of the adapter, rather than
using the one in ROM. If not specified, the address on the adapter will be
used.
Network Media:
Specifies the maximum speed at which the adapter will try to negotiate a
connection.
Offload Rx IP Checksum: Enabled
Offload Rx TcP Checksum: Enabled
Offload Rx UDP Checksum: Enabled
Offload Tx IP Checksum: Enabled
Offload Tx TCP Checksum: Enabled
Offload Tx UDP Checksum: Enabled
The above commands allow offloading various Tx and Rx processes to the
Instant Gigabit Network Adapter, freeing up system resources.
Pause Frames Count:
Flow control uses pause frames to communicate buffer status between linked
transmitting and receiving devices (transmitters and receivers). A receiver
sends a pause frame to tell a transmitter to stop transmitting data frames for a
specified period, allowing the receiver's input port buffers to empty.
Pause Frames High Threshold:
When a transmitter receives pause frames, it suspends transmission for the
specified period or until the High Threshold is reached.
Receive Drain Threshold:
Number of bytes in the current packet being drained from the rxDataFIFO
that are in fact currently in the rxDataFIFO (Note: packets larger than FIFO
size, this number will never be greater than the FIFO size).
Transmit Buffer Count: 1024 (64 - 4096)
This specifies number of transmit buffers to configure.
Transmit Drain Threshold:
This sets the maximum packet size that can be handled by the adapter since
transmit packets cannot span buffers. If not specified, this will default
depending on the amount of SRAM available and the maximum packet size
supported by the adapter.
Transmit Fill Threshold:
This setting determines the maximum number of transmits which may be
queued.
Instant Gigabit Network Adapter (EG1032/EG1064)
34
Advanced Properties
These settings are provided to help troubleshoot the Adapter and to help con-
figure the Adapter if your situation involves unusual circumstances. The
default settings of the Adapter should work in most cases. These settings
should not be altered without a thorough understanding of the specifics of
your network. If you change ANY of these settings, there is a good possibility
that the Adapter will not function properly and/or not be recognized by the
network.
Auto Negotiate
Capabilities: (Enable
or Disable)
Auto negotiates LAN
speed and duplex.
IEEE Compliance
Enable: (Enable or
Disable)
Choosing Disable may
prevent the device from
commmunicating with
other devices set to
operate on the IEEE
Standard.
Interrupt Hold Off
Time: 1 (0-255)
Specifies the time the
adapter will wait for a
busy interrupt request.
Higher values indicate
a longer wait time for
the IRQ to be free
before repeating a request.
Jumbo Frame Size: 0 (0 - 65,535)
The IEEE 802.3 standard specifies the maximum size of Ethernet frames at
1,518 bytes. A jumbo frame is simply one having up to 65,535 bytes. In a
case where a server has to receive a massive amount of data, the required
overhead of processing the individual frames could have negative effects on
the server's CPU, and ultimately on overall server performance.
Overview
Instant Gigabit Series
33