lissLights Spright Motion User manual

User’s Guide
Manufactured by: BlissLights
Phone: [phone]
Fax: [phone]
www.BlissLights.com
[e-mail]
MADE IN CHINA
Please ONLY use
manufacturer provided
power supply
motion
SPRIGHT
LASER RADIATION
AVOID DIRECT EYE EXPOSURE
DO NOT STARE INTO BEAM OR VIEM
DIRECTLY WITH OPTICAL INSTRUMENTS
CLASS 2M LASER PRODUCT
Diode Laser
Max. Output <1 mW
Wavelengths 400 - 700 nm
Manufactured by: www.blisslights.com
BlissLights, Escondido, CA 92029

TABLE OF CONTENTS
Notice ..............................................................................................................................1
Introduction ..................................................................................................................2
Before You Begin..........................................................................................................2
Parts List..........................................................................................................................2
Setting up the BlissLights Spright Motion .........................................................3
Installation Tips ............................................................................................................3
Battery Installation - Remote Control...................................................................4
Precautionary Tips for Battery Installation.........................................................4
Battery Disposal...........................................................................................................4
Using the Remote Control........................................................................................5
Increasing and Decreasing the Light Animation Speed ...............................5
Precautionary Tips for Remote Control ...............................................................5
Operating the BlissLights Spright Motion..........................................................6
Operating the Timer...................................................................................................6
Product Specications...............................................................................................6
Limited Warranty .........................................................................................................7
Owner Registration Card ..........................................................................................7

NOTICE
CAUTION—Use of controls or adjustments or performance of procedures other than those
specied herein may result in hazardous radiation exposure.
This laser product is certied as a CLASS 2M laser product, and adheres to the requirements
of the US Federal Laser Product Performance Standard (FLPPS) contained in the regulations
in 21 CFR Subchapter J.
Avoid direct viewing of a CLASS 2M laser energy, for it can be hazardous. For reference,
the FLPPS requirements for demonstration laser products, like laser pointers, are limited
to CLASS 2M levels of laser energy. This product uses diractive optics to scatter the beam
energy. This scattering eect causes the energy concentration to drop below the exposure
limits for momentary or accidental viewing at a relatively short distance from the laser
aperture. As with all bright light-sources, when you operate this device in unsupervised
general public areas, it is recommended that up-close access to the BlissLights be restricted
or prevented.
This laser display device incorporates a CLASS 3B laser system which, by itself, may be
hazardous. However, this laser display device incorporates a protective housing and
diractive holographic optics in the machine design such that there is no exposure or
human access to laser radiation during operation or maintenance above the CLASS 2M
limits. Each individual laser beamlet’s power is under 1mw, which is less than a standard
laser pointer.
UNDER NO CIRCUMSTANCES shall attempts be made to open the protective housing or
operate the device if the aperture window is damaged.
All service to this laser display device requiring the protective housing to be opened and/
or removed shall be performed by BlissLights service personnel or their authorized agents.
Opening the BlissLights protective housing voids the warranty.
NO LASERS SHOULD BE POINTED INTO THE SKY WITHIN 10 NAUTICAL MILES
OF AN AIRPORT. IF YOU ARE LOCATED WITHIN THIS SPECIFIC PERIMETER, WE
RECOMMEND THE LASERS BE POINTED DOWN AT THE GROUND SO NO STRAY BEAMS
ARE PROJECTED INTO THE AIR. CHECK WITH YOUR LOCAL AIRPORT OR COUNTY
1

INTRODUCTION
Thank you for purchasing the BlissLights Spright Motion. The BlissLights Spright Motion
is a unique indoor/outdoor light xture that uses new laser and holographic technology
to project thousands of moving pin-points of light. See the“reies” dance in your garden
without the need for wind, create a fun and mesmerizing ambience indoors, or add some
extra allure to your holiday display. We hope you enjoy this incredibly unique lighting
experience.
Each unit provides up to 2,500 square feet (50ft x 50ft) of coverage. It has maximum
electrical usage of just 9W for Green and 2W for Red and Blue, which is more energy
ecient than many LED landscape lights. It is weather resistant, making it the perfect
year-round light.
BEFORE YOU BEGIN
Immediately, upon receiving the xture: carefully unpack and check the carton contents
to ensure that all parts are present and in good condition. Notify the shipper immediately
and retain packing material for inspection if any parts appear damaged from shipping or
the carton itself shows signs of mishandling. Save the carton and all packing materials. In
the event that the xture must be returned to the factory, it is important that the xture be
returned in the original factory box. Please see parts list below for box contents.
PARTS LIST:
1) 1 x BlissLights Spright Motion Laser Fixture
2) 1 x Floor Stand
3) 1 x Remote Control
4) 2 x AAA Batteries (for use with Remote Control)
5) 1 x Ground Stake
6) 1 x AC Transformer
2
13
5
4
6
2

3
Before operating your Spright Motion, please read the “Before you Begin” section and“Notice” section of this
user guide.
INSTALLATION TIPS
• Do not connect the light to a dimmer pack, as a dimmer accessory may damage
the laser component.
• Use only the manufacturer-provided power supply. You may plug your BlissLight into
any ordinary 110/120V AC electrical outlet indoor or outdoor.
• Limit the use of extension cords. If you need an extension cord, use only UL, CUL, or
CSA approved 3rd party extension cords. When using outdoors, ONLY use extension
cords that are weather resistant, such as waterproof cords.
• The darker the display area the brighter your projection will appear. Try to avoid
display areas with strong ambient light sources, such as commercial street lights or
bright security ood lights.
• If you are going to mount the BlissLights Spright Motion for downlighting (e.g. from
balcony railing, fence line, roof line, etc.), it is recommended that, for safety purposes,
your lights are properly mounted using a suitable hanging clamp and safety cable.
SETTING UP THE BLISSLIGHTS SPRIGHT MOTION
GROUND STAKE ACCESSORY: Use the included ground
stake when placing and positioning the xture into
the soft earth outdoors. Simply stake the BlissLights
Spright Motion into the desired location holding the
top of the ground stake and gently piercing the stake
into the ground. Do not grasp xture head when
staking your BlissLight into the ground. Attach
the stake to the xture head by twisting xture
clockwise, and remove the stake by twisting xture
counterclockwise. Adjust the angle of projected light
by turning the thumbscrew attached to the side of
the xture.
FLOOR STAND ACCESSORY: Use the included stand as a
quick and easy alternative to the ground stake when
placing and positioning the xture on any hard, at
surface area indoors (i.e. oor, window sill, top of
cabinet, inside staircase or bookshelf) or outdoors (i.e.
porch, sidewalk, patio table, deck). Attach the stand
to the xture head by twisting xture clockwise, and
remove stand by twisting xture counterclockwise.
Adjust the angle of projected light by turning the
thumbscrew attached to the side of the xture.

BATTERY INSTALLATION - REMOTE CONTROL
1. Remove battery compartment cover.
2. Insert two AAA batteries (included) into the remote control.
Note: Make sure to match the (+) and (-)symbols on the batteries with the (+) and (-)
symbols inside the battery compartment.
3. Re-attach the battery compartment cover.
4
PRECAUTIONARY TIPS FOR BATTERY INSTALLATION
• Do not ingest batteries.
• Non-rechargeable batteries are not to be recharged.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the product.
• Do not mix old and new batteries.
• Do not mix Alkaline, standard (carbon zinc), or rechargeable (NiCad, NiMH, etc.)
batteries.
• Only use AAA batteries.
• Install only new batteries of the same type.
• Failure to insert batteries in the correct polarity, as indicated in the battery
compartment, may shorten the life of the batteries or cause batteries to leak.
• Do not mix old and new batteries.
• Do not take apart the batteries, heat them, or throw them into a re.
• Keep the batteries away from children and pets.
• When not using the remote control for a long period of time, remove and store
batteries in a cool, dry place at normal room temperature.
BATTERY DISPOSAL
Please, always dispose of batteries at a suitable recycling point.
Note: Batteries should be recycled or disposed of as per
state and local guidelines.
Note: For best results, use only
alkaline batteries.

5
USING THE REMOTE CONTROL
Power Button - Press to turn on or o.
+ Button – Press to increase the speed of the star eld’s rotation.
- Button – Press to decrease the speed of the star eld’s rotation.
INCREASING AND DECREASING THE LIGHT ANIMATION SPEED
Press the (+) or (-) buttons on your remote to increase or decrease the light animation
speed. The light projection will blink ONCE after each speed-setting change and TWICE
after it has reached the fastest or slowest speed-setting.
Remote FCC Compliance:
This device complies with Part 15 of FCC Rules. Operation is subject to the following two
conditions: 1. this device may not cause harmful interference, and 2. this device must accept
any interference received, including interference that may cause undesired operation.
PRECAUTIONARY TIPS FOR THE REMOTE CONTROL
• The remote control should be kept dry and away from heat sources. Avoid humidity. If
the device responds erratically to the remote control, or doesn’t respond at all, check
the batteries.
• Do not subject the remote control to undue physical stress, such as striking or
dropping it.
• Do not attempt to clean the remote control with a volatile solvent. Wipe it with a clean,
damp, soft cloth for cleaning.

6
OPERATING THE BLISSLIGHTS SPRIGHT MOTION
The Blisslights Spright Motion operates in temperatures of -15°F to 90°F. There may be a
slight delay in projection intensity if operating in temperatures below 55°F. Please allow up
to 10 minutes for the light to warm up and reach its full projection intensity.
OPERATING THE TIMER
When you rst plug in your light, it will automatically turn on and will operate at its fastest
rotation speed. It will continue on for 6 hours, or until it is shut o using the remote control.
Using the remote control to shut o the unit also disables the timer, and every time it is
turned on, it will reset the timer.
The Blisslights Spright Motion has a built-in timer that is designed to automatically shut o
after 6 hours of operation. It will go into sleep mode for 18 hours, and resume its operation
thereafter. The rotation speed will remain at the same setting for every timer cycle, unless
you unplug the unit, which will return it to the fastest rotation speed.
Laser Classication Class 2M
Laser Power Less than 1 mW per beamlet,
Laser Wavelength 660nm - Red, 532nm - Green, 445nm - Blue
Laser Optics Single-source holographic optical element
Power Consumption <9W (Green), <2W (Red/Blue)
110/120V AC with manufacturer provided
power supply
Power Input (Device) 12V AC or DC
Operation Indoor/Outdoor
Operating Temperature -15°F to 90°F ( -26°C to 32°C)
Projection Coverage Up to 50ft x 50ft
Maintenance Maintenance Free
144mm x 200mm x 128mm, 720g
PRODUCT SPECIFICATIONS
5.6in x 7.9in x 5in, 1.6lbs
Cord Length: 6m / 20ft
Limited One Year
Warranty
Dimensions
Power Input

LIMITED WARRANTY
The manufacturer warrants this product to be free from defects in materials and workmanship for a period of one (1) year from
date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and
service. If this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or
replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse,
abuse, accident, modications, alterations, neglect or mishandling. This warranty shall not apply to any product that is found to
have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product.
This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, or faulty
installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the nish on any
portion of the product, such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not
warrant and specially disclaims any warranty, whether expressed or implied, of tness for a particular purpose, other than the
warranty contained herein. The manufacturer specically disclaims any liability and shall not be liable for any consequential or
incidental loss of damage, including any labor/expense costs involved in the replacement or repair of said product. This warranty
gives you specic legal rights and you may also have other rights which vary from state to state. Please contact BlissLights at
[email protected], or (626) 709- 3319.
Owner Registration Card
Please ll out, cut along dashed line, ax proper postage and return this Owner Registration Card to insure that your new
BlissLights Spright Motion is covered by the limited warranty. You can also register your product online by going to
www.blisslights.com. Registering your product will help expedite your warranty related requests, but is not required.
Mailing Address: BlissLights, 1155 Industrial Avenue, Escondido, CA 92029
Purchaser’s Name: _________________________________________________________
Address: _______________________________________________________________
City / State / Province: ____________________________ Zip: ______________________
Email: ________________________________________________________________
BlissLights Product: ________________________ Purchase Date: ______________________
Where Purchased (Store Name) _________________________________________________
Where will the BlissLights be used: _______________________________________________
If commercial institution, what type of business?
q Restaurant q Bar q Store q Oce q Other: ____________________________________
If home installation, where?
q Walkway q Patio q Garden Area q Porch q Other: ________________________________
Model/UPC Number:________________________________________________________
7