LITEMATRIX Line L65AG Series User manual

Instruction Line Pendant
LITEMATRIX(HK) CO LIMITED Phone: [phone] LiteMatrix reserves the right to make technical and design
changes without prior notice.
Flat A 8/F No.227 Nathan Road Yau Ma Tei Kowloon Hongkong Fax: [phone]
www.litematrixlighting.com E-mail: [email protected] 2017.10 1 / 3
L65AG L65AG DI
Instruction of installation：
—Read the instructions carefully before installation and commissioning.
—The safety of the device can only be guaranteed on condition that to be respected the following instructions, both stages of installatio
n and use therefore it is highly
recommended to keep them.
—When installing, always observe the national installation and accident prevention regulations.
—Installation and commissioning may only be carried out by authorized specialists.
—The device cannot be in any case modified or forced, any modification might jeopardize the safety system making it dangerous. LiteMatrix declines a
ny responsibility
on modified products
FOR INDOOR USE ONLY!
ATTENTION: For suspension mounting. Luminaire not suitable for being covered with heavy staffs or thermally insulating materials.
Table 1-Parameters
L A H Mass Finish Color of
reflector
mm mm mm kg
LAG-565
565 80-100 Max.
2000
2.6 White/
Black
White/
Silver
LAG-565-DI 2.8
LAG-1125
1125 80-100 Max.
2000
5.0 White/
Black
White/
Silver
LAG-1125-DI 5.2
LAG-1685
1685 80-100 Max.
2000
7.8 White/
Black
White/
Silver
LAG-1685-DI 8.0
LAG-2245
2245 80-100 Max.
2000
10.4 White/
Black
White/
Silver
LAG-2245-DI 10.8
-Lateral air space under EN 60598: The lateral distance between the surface of
the luminaire and any parts of the building must be no less than 50mm.
-Please DO NOT exceed the rated load-bearing of ceilings.
-Recommended mounting and using environment: Ta=25℃.

Instruction Line Pendant
LITEMATRIX(HK) CO LIMITED Phone: [phone] LiteMatrix reserves the right to make technical and design
changes without prior notice.
Flat A 8/F No.227 Nathan Road Yau Ma Tei Kowloon Hongkong Fax: [phone]
www.litematrixlighting.com E-mail: [email protected] 2017.10 2 / 3
Installation of live end 7. Install and then fix the junction box Power Connection of live end Interconnection
1. During the installation, make sure
the power supply is disconnected. Put
on gloves and operate in dry environ-
ment
For DALI versions 1. Remove the end caps
2. Mark the location of suspension
cord according to table 1.
2. Put connecting device into body
Installation of non-live end
1. Suspension cord installation
For On-off/Wireless versions
3. Ceiling cutout.
3. Fix them
Installation of lamp body
1. Fix the suspension cord
4. Power connection.
4. Install the fixing part
2. Adjust the suspension cord to
maintain horizontal
Power Connection of non-live end
Connect via quick coupling
5. Install suspension cord through A
to B
5. Assemble adjacent luminaires and
fix them together.
ATTENTION:
For safety consideration, during the
installation, make sure the power supply
is disconnected.
Avoid any damage to supply cable.
Su
spension cord should not be longer
than supply cable
Single or continuous line available. The
maximum load current should not
exceed 5A.
6. Connect to power supply(Refer to
Power Connection part)
6. Fix the end caps and suspend.

Instruction Line Pendant
LITEMATRIX(HK) CO LIMITED Phone: [phone] LiteMatrix reserves the right to make technical and design
changes without prior notice.
Flat A 8/F No.227 Nathan Road Yau Ma Tei Kowloon Hongkong Fax: [phone]
www.litematrixlighting.com E-mail: [email protected] 2017.10 3 / 3
Reflector change
Reflectors are fixed by magnet force
and convenient to be removed or
installed by hand. Black or silver
available.
Cleaning
Always clean carefully using a soft
cloth and a commercially available, ph-
neutral, alcohol-free, non-abrasive
cleaning agent.
Disposal
In accordance with EU Directive
WEEE
(Waste Electrical and Electronic
Equipment), luminaires must not be
disposed of with other household
waste. At the end of their life,
luminaires must be taken to the
appropriate local facility available for
the disposal
or recycling of electronic
products.