Little Colorado Treasure Chest 53 User manual

Treasure Chest Assembly Instructions; Stock # 53
• Please inspect the parts for damage during shipping and for any missing items. If you suspect that there may be damage or a shortage, contact us
and we will send replacement parts if needed.
• As soon as components and hardware are unpacked; please remove and recycle all plastic bags from possible contact with children.
• Words in Red represent a component or hardware used in assembly.
• Illustrations are intended to help identify components and hardware and are not drawn to scale.
Revised 5/15
by
C. Collinson
Please read instructions carefully to
avoid accidental damage to
components during assembly.
Treasure Chest Hardware
1- Lid Support
Treasure Chest Components
Page 1 of 3
Tools needed for assembly
• Medium size #2 Phillips
Screwdriver
4- #8 5/8 in.
Wood Screws
12- Cam Locks
12- Cam Posts
14- #5 5/8 in.
Wood Screws
Lid
Front
Back
Side
Bottom
Top Bottom
Quality Wooden Children’s Furniture and Accessories
Made in America • Established 1987
www.littlecolorado.com
Side
WARNING: ADULT ASSEMBLY REQUIRED
WARNING: Assembly kit contains parts with sharp points.
WARNING: Assembly kit contains parts with sharp edges.
WARNING: Package contains plastic bags that present suffocation risks for children.
WARNING: Assembly kit contains small parts that present choking hazards for children.

Treasure Chest Assembly Instructions- Continued
Revised 5/15
by
C. Collinson
• Now that you have the two sides
fastened to the back; slide the
bottom panel in the bottom grooves
(The side with the Little Colorado
logo is the top side).
• Insert Cam Posts in holes on edge
of Side. This maybe a tight t. Some
minor adjusting and tting may be
needed.
• Insert 3 Cam Locks into the Cam Lock
holes on the side component . The
arrow head on the face of the Cam
needs to be pointing toward the head
of the Cam Post.
•Turn the Cam 1/2 turn Clockwise
until cam stops.
• Now, repeat steps 2 and 3 to
assemble the other side.
• Use a #2 Phillips head screwdriver to screw
in 3 Cam Posts to each side of Back.
• Each cam post must be fully seated and
perpendicular.
• Repeat steps 1, 2 and 3 to attach
Front panel to body
12 3
456
Page 2 of 3
Partial view of Side
• Using the existing holes, attach bottom of
Lid Support to inside of Back with 2 #8 x 5/8”
screws
• Place Lid on top of the box and line
up existing holes located on outside
of the back panel to holes in hinge.
Attach hinge to back of box using 14
#5 x 5/8” screws.
• Be careful not to over tighten screws.
Bottom
Quality Wooden Children’s Furniture and Accessories
Made in America • Established 1987
www.littlecolorado.com
Arrow Head
Bottom Panel
Panel Groove
Cam Post Holes
Cam Lock Holes
Body
Lid
Back
Top
Lid Support
Back Panel
Area of Detail

Quality Wooden Children’s Furniture and Accessories
Made in America • Established 1987
www.littlecolorado.com
Treasure Chest Assembly Instructions- Continued
Revised 5/15
by
C. Collinson
Please Recycle Instructions
• Now that you have completed the assembly,
open and close the lid 10 times to break in the
lid support mechanism.
•The lid should not fall when the Lid Support is
properly installed.
• If the lid does not stay in position when raised,
please call us and we will help you. Until the lid
support is properly installed, do not allow
children to use this product. Please check the
mounting screws periodically to be sure they
remain tight,
• Carefully open up lid to 85 degrees and hold it
in that position. Then attach the top mounting
bracket of the Lid Support to the inside of the
lid using the existing holes and 2 #8 screws.
• It is very important that the existing holes line
up perfectly or the lid support may not function
properly.
•Be careful not to over tighten screws.
78
If you would like your Treasure Chest Personalized with
your child’s name. Contact us at 303 964 3212 and
we will take your order and mail you your child’s name
complete with mounting instructions.
If you have any problems, please call us and we will help you 303 964 3212 or email [email protected] 4450 Lipan St.,Denver, CO 80211
Page 3 of 3
Use and Care Instructions
The nish on this product is an environmentally friendly water base acrylic made by Sherwin Williams. It may be cleaned with a furniture polish, lemon oil or a
non abrasive cleaner using a soft cloth. DO NOT USE AMMONIA or products containing ammonia such as Windex glass or
multi-surface cleaner. Scuff marks can usually be removed by using a polishing compound sold at auto parts stores.
Little Colorado, Inc is a family run children’s furniture manufacturer located in Denver. Please check out www.littlecolorado.com to see our other products that
are all made here in America. The safety of your children is our highest concern. We are a GREEN company and hope you will be able to recycle the packag-
ing material that we used to ship your product.
If you have a comment or a question please contact us at info at [email protected]. All of us at Little Colorado hope you and your family will enjoy this
product for many years.
WARNING
Failure to properly install
the lid support will result in
an entrapment hazard
Lid
Body