LIVING AND HOME PERGOLA User manual

1
PERGOLA

2
ASSEMBLY GUIDE

We strongly recommend the use of work gloves during assembly.
 Do not attempt to assemble the PERGOLA in windy or wet conditions.

Do not touch overhead power cables with the aluminum profiles.
 Always wear shoes and safety goggles when working with extruded
aluminum.
 Dispose of all plastic bags safely and keep them out of reach of children.
 The PERGOLA must be positioned and fixed on a flat level surface.
 Do not lean against or push the PERGOLA during construction.
 Keep children away from the assembly area.

Do not position your PERGOLA in an area exposed to excessive wind.
 Do not attempt to assemble this PERGOLA if you are tired, have taken
drugs or alcohol or if you are prone to dizzy spells.

If using a step ladder or power tools ensure that you follow the
manufacturer's safety advice.

Hot items such as recently used grills, blowtorches etc., must not be stored
in the PERGOLA.
 Ensure there are no hidden pipes or cables in the ground before inserting
the pegs.
 This is a multi-part assembly, allow at least 1.5 hours for assembly.
 Selecting a site--choose a sunny level position away from overhanging
trees.
 If you are fixing your PERGOLA directly to a solid concrete foundation use
the pre-drilled holes in the metal base supplied.

3
 The component parts should be checked and laid out close to hand.
 Keep all small parts (screws etc.) in a bowl so they do not get lost.
Weather Protection:

WARNING: If there is lightening, do not stay in or under the product. The
frames are constructed of metal, which is conductive, and may cause
serious damage.

When wind power reaches 40mph or above, you may need to set up
defense equipment and fix the columns. To fix the columns, use a strong
rope or cable and connect to the four angles of the anchors with a block
inserted into the soil or tied to a nearby tree at least 4in. in diameter.
When wind decreases, please remove safety measures of ropes.
 Clear any leaves and branches on top of pergola to prevent the fabric from
damage and dirty.

4
COMPONENTS
A: (x2)
B: (x2)
C: (x4)
D: (x2)
D1: (x2)
E: (x1)
E1: (x1)
F: (x12)

5
F1: (x6)
F2: (x2)
G : (x2)
I: (x4)
J: (x8)
M6 x 50
L: (x12)
M6 x 15
K: (x24)
M6 x 30
O: (x44)
Q: (x36)
P: (x2)
M: (x1)

6
PART LIST

7
INSTALLATION
Step 1
Install the top frame as shown.

8
Step 2
Attach four pillars to the top frame and then install foot pads at the bottom of
the pillars as shown in the figure.

9
Step 3
Attach the polyester fabric to the top of the pergola.

10
CARE & MAINTENANCE

When your PERGOLA needs cleaning, use a mild detergent solution and
rinse with cool clean water. Do NOT use acetone, abrasive cleaners or
other special detergents to clean the fabric.
 If the ground is not level, the unit may tilt to one side. If you find this is the
case, please fix immediately to avoid damage.
 Please prevent adding any increased weight to the product.
 Avoid any vine/climbing plants, fruits, or vegetables from growing on the
pergola as to not compromise the structure and durability of the product.
 If the structure is compromised, it can easily cause the frame to crack,
break, or collapse.
 When using the product, please do not use sharp objects on collision films
to avoid cuts. Be careful not to have a sharp object touch the film as it may
scratch.
 The fabric have flame polyester material applied to them and is
recommended to keep away from fire to avoid damage.

The frames are made of metal structure. If white spots or dirt is shown,
please wipe with a wet cloth. White spots are normal in a wet/warm
environment.

If there is any distorting with the calibration, please fix immediately. Any
distortion can cause the skylight to fall. Please refer to the instruction
manual for repairs.
 If any connection piece rusts, change out the screws to ensure the
connection part is firm and stable.